• 한국의학물리학회지:의학물리
• /
• 제27권4호
• /
• pp.196-202
• /
• 2016

We aim to develop the breast bolus by using a 3D printer to minimize the air-gap, and compare it to commercial bolus used for patients undergoing reconstruction in breast cancer. The bolus-shaped region of interests (ROIs) were contoured at the surface of the intensity-modulated radiation therapy (IMRT) thorax phantom with 5 mm thickness, after which the digital imaging and communications in mdicine (DICOM)-RT structure file was acquired. The intensity-modulated radiation therapy (Tomo-IMRT) and direct mode (Tomo-Direct) using the Tomotherapy were established. The 13 point doses were measured by optically stimulated luminescence (OSLD) dosimetry. The measurement data was analyzed to quantitatively evaluate the applicability of 3D bolus. The percentage change of mean measured dose between the commercial bolus and 3D-bolus was 2.3% and 0.7% for the Tomo-direct and Tomo-IMRT, respectively. For air-gap, range of the commercial bolus was from 0.8 cm to 1.5 cm at the periphery of the right breast. In contrast, the 3D-bolus have occurred the air-gap (i.e., 0 cm). The 3D-bolus for radiation therapy reduces the air-gap on irregular body surface that believed to help in accurate and precise radiation therapy due to better property of adhesion.

• 한국재료학회지
• /
• 제11권4호
• /
• pp.272-277
• /
• 2001

WO$_3$에 NiO를 첨가하여 제조한 후막형 시편의 미세구조와 전기적 성질에 대해 연구하였다. NiO 첨가에 따른 WO$_3$의 결정립 성장이 억제되었고, 입도 분포도 균일하였으나 첨가량에 따른 결정립 크기 변화정도는 작았다. 산소 분압 감소로 WO$_3$의 전도성은 증가하였고, NiO 첨가에 의해 고용한계 이하에서는 전도성이 증가하였고, 이상에서는 전도성이 감소하였다. 온도 증가에 따라 외인성 (extrinsic) 구간에서는 전도성 변화가 적었고, 고온의 진성 (intrinsic) 구간에서는 전도도가 급격히 증가하였으며, 이들의 중간 온도에서는 산소흡착에 따라 전도도가 감소하였다.

• 한국건축시공학회지
• /
• 제20권2호
• /
• pp.199-212
• /
• 2020

In evaluating the competitiveness of construction companies and their development strategies, patents are a useful and objective source of technical information. In this study, the cutting-edge technologies of construction industries of China, Japan, and South Korea were investigated based on the data of patent applications filed by a total of 15 construction companies (five companies from each country). The related technologies were classified into six core technology groups based on their keywords. After that, we used four patent analysis methods: time series analysis, IP (Intellectual Property) emergence level analysis, spiral module analysis, and OS (Object-Solution) Matrix analysis, to identify the promising technologies/vacant technologies for global construction companies in China, Japan, and South Korea, and to analyze the technical competitiveness of the three countries. The findings of this study showed that each country can claim a relative technological advantage over the others. Overall, 3D printing and offsite construction technology, data acquisition technology, AR and VR technology are expected to be promising in the Asian region. The present study contributes to the body of knowledge by expanding our understanding of technological innovation for the competitiveness of companies and the technology development strategies pursued by the construction industries of China, Japan, and South Korea.

• 펄프종이기술
• /
• 제45권4호
• /
• pp.1-8
• /
• 2013

High loading of printing and writing grades with fillers has many advantageous aspects in papermaking because it allows decreasing fiber use and reducing manufacturing cost. High loading technology, however, has some disadvantageous aspects as well. It decreases physical properties of papers, especially strength properties. The problem associated with high loading can be reduced by applying surface sizing starch solution onto paper surface. It is important to control the penetration of the surface sizing starch solution into paper web to obtain the desired property improvement. In this study, the effect of the addition of two polymers into starch solution on paper properties has been examined. PVOH and polyDADMAC were used as polymeric additives for surface sizing with oxidized starch. Viscosity of starch solutions and surface roughness of dried starch films on glass slides showed that some interactions between polymeric additives and oxidized starch have been occurred and the most extensive interaction with starch solution was obtained with high molecular weight polyDADMAC. Low molecular weight PVOH was most effective in improving folding endurance and internal bond strength. On the other hand, polymer addition showed no effect on surface strength of paper. This indicates that not the level of starch holdout but the bonding strength of starch itself has predominant influence on surface strength of paper.

• 대한기계학회논문집A
• /
• 제41권7호
• /
• pp.607-612
• /
• 2017

최근 다양한 분야에 적용되고 있는 적층 가공 기술(AM)은 복잡한 형상 제조 및 재료 비용 절감으로 인해 혁신적인 제품 생산 방법으로 각광을 받고 있다. 그 중에서도 압출적층조형(Fused Deposition Modeling, FDM) 공정을 통한 친환경 부품 제조는 의료 분야산업에서 많은 주목을 받고 있다. 따라서, 본 논문에서는 친환경 생분해성 재료인 Poly Lactic Acid(PLA)를 사용한 FDM 공정 실험을 수행하고 제작된 적층 시편에 대한 인장 시험을 적용하여 주요 FDM 공정 변수인 적층 두께, 적층 방향, 적층 충진량이 인장 시편의 기계적 성질에 미치는 영향을 정량적 및 정성적으로 분석하고 이를 극대화하는 각 공정 변수의 최적값을 도출하였다.

• 반도체디스플레이기술학회지
• /
• 제19권1호
• /
• pp.79-84
• /
• 2020

Unlike a printing process, it is difficult to pattern organic thin films in the longitudinal (coating) direction using a coating process. In this paper, we have investigated the feasibility of patterning organic thin films using needles. To this end, we have slot-coated an aqueous poly(3,4-ethylenedioxythiophene):poly(4-styrenesulfonate) (PEDOT:PSS) solution in the form of a fine stripe or large area and then applied the dual needle; one for discharging the main solvent of the underlying thin film and the other for sucking the dissolved thin film. We have found that the pattern width and depth increase as the moving speed of the plate decreases. However, it is observed that the sidewall slope is very gentle (the length of the slope is of the order of 200 ㎛) due to the fact that the discharged main solvent is widely spread and then isotropic etching occurs. With this scheme, we have also demonstrated that a fine stripe can be obtained by scanning the dual needle closely. To demonstrate its applicability to solution-processable organic light-emitting diodes (OLEDs), we have also fabricated OLED with the patterned PEDOT:PSS stripe and observed the insulation property in the strong light-emitting stripe.

• 한국전기전자재료학회논문지
• /
• 제33권6호
• /
• pp.465-470
• /
• 2020

Heterolayered K(Ta,Nb)O₃/Pb(Zr,Ti)O₃ thin films on Pt/Ti/SiO₂/Si substrates were prepared by a sol-gel process and spin-coating method. The structural and electrical properties were measured to investigate the possibility of application as an electrocaloric effect device. All specimens exhibited dense and uniform cross-sectional structures without pores, and the average thickness of the specimen coated six times was approximately 394 nm. Curie temperatures were observed at 5℃ or less in type-I and 10℃ in type-II specimens, respectively. Type-II specimens coated 6 times showed a relative dielectric constant of 758 and remanent polarization of 9.71 μC/㎠ at room temperature. The maximum electrocaloric effect occurred between 20 and 25℃, slightly higher than their Curie temperature, and the electrocaloric property (ΔT) of the type-II specimens coated 6 times was approximately 1.2℃ at room temperature.

• 펄프종이기술
• /
• 제30권3호
• /
• pp.74-83
• /
• 1998

The phenomenon of decrease in sizing efficiency when the stock temperature is increased is well recognized as summer sizing, and this is believed to be caused by uneven distribution of sizing agents on paper surface most often incurred by coagulation of sizing agents. When unevenly sized paper is used as coating base stock, nonuniform consolidation of the coating layer may result, which, in turn, causes uneven distribution of binder on coating surface. This causes nonuniform ink absorption to produce print mottle. In this study the effects of simple or polymeric electrolytes, storage temperature and time on the coagulation of cationic dispersed rosin size were investigated using a turbidity measurement method which was verified to correlate well with the particle size of rosin emulsion or its coagulates. Handsheets sized with rosin dispersions coagulated under various conditions were prepared and their sizing degree and coated paper properties including gloss and ink density were examined. The relationship between the sizing nonuniformity of coated papers and its ink absorption property was evaluated. Turbidity of rosin emulsion increased as the storage temperature and time were increased. Addition of simple or polymeric electrolytes caused reduction in $zeta$ -potential of the rosin dispersion and accelerated the coagulation tendency substantially. Reversion of the $zeta$ -potential of rosin dispersion, however, did not occur when coagulation was induced with simple electrolytes. On the other hand, addition of an anionic polyelectrolyte reversed the $zeta$ -potential of the flocculated rosin dispersion. This indicated that electrical double layer compaction and bridging flocculation were coagulation mechanisms for simple and polymeric electrolytes, respectively. Sizing degree decreased as coagulation of rosin was increased. Paper gloss, ink gloss and ink density were increased when sizing degree of base stock was increased most probably due to prevention of base paper swelling and increased binder migration to coating surface. This suggested that uneven printing ink density occurred when uneven sizing development was induced by coagulation of rosin particles.

• 한국의학물리학회지:의학물리
• /
• 제30권1호
• /
• pp.32-38
• /
• 2019

Purpose: The objective of this study is to evaluate the geometrical accuracy of a patient-specific bolus based on a three-dimensional (3D) printed mold and casting method. Materials and Methods: Three breast cancer patients undergoing treatment for a superficial region were scanned using computed tomography (CT) and a designed bolus structure through a treatment planning system (TPS). For the fabrication of patient-specific bolus, we cast harmless certified silicone into 3D printed molds. The produced bolus was also imaged using CT under the same conditions as the patient CT to acquire its geometrical shape. We compared the shapes of the produced bolus with the planned bolus structure from the TPS by measuring the average distance between two structures after a surface registration. Results and Conclusions: The result of the average difference in distance was within 1 mm and, as the worst case, the absolute difference did not exceed ${\pm}2mm$. The result of the geometric difference in the cross-section profile of each bolus was approximately 1 mm, which is a similar property of the average difference in distance. This discrepancy was negligible in affecting the dose reduction. The proposed fabrication of patient-specific bolus is useful for radiation therapy in the treatment of superficial regions, particularly those with an irregular shape.

• 한국산학기술학회논문지
• /
• 제19권12호
• /
• pp.25-31
• /
• 2018

선택적 레이저 용융 (Selective Laser Melting) 기법은 금속 소재를 다루는 대표적인 3D 프린팅 기법중의 하나이다. SLM 기법으로 제작되는 구조물의 특성을 좌우하는 주요 제작 인자로는 구조물의 적층 제작 방향, 레이저 파워, 레이저 스캔 스피드 및 스캔 간격 등을 고려할 수 있다. 이번 연구에서는 AlSi10Mg 합금을 대상 소재로 하여, 인장 시편의 제작 방향, 레이저 스캔 스피드 및 스캔 간격을 변수로 하여, 인장특성 결과를 비교 분석하였다. 인장특성으로는 항복 응력, 인장강도 및 연신율을 고려하였다. 시험결과로부터, 인장 시편의 제작 방향 기준으로 0도, 45도, 90도 순서로 항복 응력 값이 낮아짐을 확인하였다. 레이저 스캔 스피드 기준으로는 1870mm/min에서 가장 큰 항복 응력값을 보였으며, 스캔 스피드가 낮아질수록 항복 응력 크기도 줄어들었다. 레이저 스캔 간격 기준으로, 그 크기가 증가할수록 항복 응력값은 증가하지만, 다른 시험 기준에 비해 그 변화폭은 가장 적었다. 인장강도 및 연신율은 시험조건에 따른 명확한 경향성을 파악하기 어려웠다.