• Journal of the Korean Ceramic Society
• /
• v.33 no.9
• /
• pp.1057-1063
• /
• 1996

Y2O3-CeO2-ZrO2 powders were prepared from water-soluble salts using a coprecipitation method. The forming process of oxide and the characteristics of the calcined powders treated in different drying conditions were investigated. The oxidation was occurred at the temperature of around 40$0^{\circ}C$ and the main crystallization of ZrO2 around $600^{\circ}C$. On calcination at $600^{\circ}C$ heating lamp-dried powders consisted of agglomerates of globular morphology with average agglomerate size of 2.27${\mu}{\textrm}{m}$ and specific surface area of 68.3m2/g and spray dried powders contained dense spheric particles with average agglomerate size of 1.35${\mu}{\textrm}{m}$ and specific surface area of 11.0m2/g which exhibited low agglomeration tendency. Removal of the water by a freeze-drying technique produced calcined powders containing flake-like secondary particle structures with wide agglomerate size distri-bution of 0.1-60${\mu}{\textrm}{m}$ and specific surface area of 24.5${\mu}{\textrm}{m}$. The 20 MPa-pressed density (36.8-41.4% T,D) of calcined powders did not nealy depend on drying methods whilst compaction ratio of calcined powders derived from freeze-drying was the highest ( 6.24) among three drying methods. On continuous heating up to 150$0^{\circ}C$ the sinterability of calcined powders derived from heating lamp-drying was superior to those derived from spray-and freeze-drying. The final sintered density of calcined powders was the highest (96% T,D at 150$0^{\circ}C$) in case of heating lamp-drying.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.16 no.6
• /
• pp.244-249
• /
• 2006

Electrostatic spray pyrolysis, a novel fabrication technique, has been used in this study to prepare calcium phosphate nano powders. Final annealing was done at $400^{\circ}C$ for 30min in air. The hydroxyapatite - forming ability of the annealed powder has been evaluated in Eagle's minimum essential medium solution (MEM). X-ray diffraction analysis, field emission - scanning electron microscope, energy dispersive X-ray spectroscope, and Fourier transform infrared spectroscope were used to characterized the annealed powders after immersion in MEM. The powder with an amorphous structure induced hydroxyapatite formation on their surfaces after immersion fer 15 days.

• Journal of the East Asian Society of Dietary Life
• /
• v.1 no.1
• /
• pp.17-29
• /
• 1991

The Hong's-Zu-Bang-Moon, although it is not know when and by whom it was written, is estimated to have written in the middle of 1800, but has not been published yet. In general, other cooking books in Yi's Dynasty were on the cooking methods of a variety of foods. But the book deals solely with brewing, which is the trait of it. The book comprises a total of 36 items, among which So-Gog-Ju wine was excluded because only a part of it was recorded. Another item deleted, written vaguely and difficult to understand was, on a closer analysis of its content, 'Song-Soon-Ju wine'. According to the analysis of this book, the cereals used for brewing were 59 percent of regular rice and 41 percent of sticky rice including other 12 kinds of special materials. As for the processes, the precesses using Jee-Ae-Bop was dominant. The processing technique whose special words and expressions were analyzed in this study, were divided into 18 preparation methods, 45 processing ones, and 7 heating ones. The temperature processing whose expressions were analyzed here were divided into 6 cooking processes, 7 medium ones and 3 heating ones. The measurement unit of 'Doe' was most often used. It tried to show relatively accurate measurements but showed just approximate ones. There were 19 kinds of brewing utensis. Urns were most often used, but it was impossible to discern and kind. As for the tast of the wines, the writer showed his subjective expressions. The margianal point in this study is that it was very difficult to interpret the book. The closing up of twings of on azaled over the urn had no scientific base but said something of korean folkways at that times.

• Clinical and Experimental Reproductive Medicine
• /
• v.15 no.2
• /
• pp.149-155
• /
• 1988

To increase fertilization rate in vitro, separation of viable spermatozoa from the seminal plasma and its other components may be a useful procedure. Ejaculates from healthy men, whose semen analysis findings were normal in 19, and abnormal in 10, were filtered using the glass-wool filtration technique to yield a concentrated, viable sperm samples for IVF, and the usefulness and safety of this method were evaluated. The recovery rate of motile sperm in abnormal groups was 46.2% and 54.5% in normal group. The % motility was increased significantly compared with original sample after filtration, and the grade motility was improved, too. The sperm population with normal morphology was also increased significantly in both group. Using transmission electron microscopy, the ultrastructural integrity of acrosomal segment was examined in order to evaluate the potentially hazardous effect of glass-wool filtration to sperm head, however, sperm population with normal ultrastructure was increased compared with that of original ejaculate after separation. The filtered sperm was then processed for IVF, as the fertilizing capacity is the ultimate parameter of the sperm function. In abnormal group, the fertilization rate(41.5 %) and the ET rate per stimulated cycle were much lower than that of mormal group(69.6%). However, the cleavage rate and the number of embryos transfered per ET cycle were comparable with those of nomal group. The results suggest that the glass-wool filtration of sperm, particularly in oligo-asthenozoospsrmia, may be useful and safe method in the preparation of sperm for IVF.

• Elastomers and Composites
• /
• v.44 no.3
• /
• pp.209-221
• /
• 2009

Polyolefins are important commodity polymers with the largest volume of business owing to their outstanding combination of cost performance and excellent physical properties. However, the lack of functional groups often has limited their end uses, such as compatibilizer, modifier and adhesive, where the interaction with other materials is especially important. The incorporation of functional groups as polymer segments to afford block or graft polyolefin copolymers has been extensively investigated in the context of the functional polyolefin hybrids. Living polymerization processes have been considered to be an efficient method to prepare the polyolefin hybrids with precisely controlled architecture and compositions. Among the living polymerization techniques, controlled/"living" radical polymerization (CRP) methods are very effective not only because of the controllability of polymerization but also because of the versatility of monomers and polymerization conditions. In this review paper, progresses on the preparations of polyolefin graft or block copolymers through CRP techniques are summarized. The commodity polymers such as polyisobutylene, polyethylene and polypropylene are combined with polar segments such as polyacrylate, polymethacrylate, polystyrene to yield functionalized polyolefins.

• Bulletin of the Korean Chemical Society
• /
• v.27 no.1
• /
• pp.65-70
• /
• 2006

An amperometric glucose biosensor has been developed based on the use of the nanoporous composite film of sol-gel-derived zirconia and perfluorosulfonated ionomer, Nafion, for the encapsulation of glucose oxidase (GOx) on a platinized glassy carbon electrode. Zirconium isopropoxide (ZrOPr) was used as a sol-gel precursor for the preparation of zirconia/Nafion composite film and the performance of the resulting glucose biosensor was tuned by controlling the water content in the acid-catalyzed hydrolysis of sol-gel stock solution. The presence of Nafion polymer in the sol-gel-derived zirconia in the biosensor resulted in faster response time and higher sensitivity compared to those obtained at the pure zirconia- and pure Nafion-based biosensors. Because of the nanoporous nature of the composite film, the glucose biosensor based on the zirconia/Nafion composite film can reach 95% of steady-state current less than 5 s. In addition, the biosensor responds to glucose linearly in the range of 0.03-15.08 mM with a sensitivity of 3.40 $\mu$A/mM and the detection limit of 0.037 mM (S/N = 3). Moreover, the biosensor exhibited good sensor-to-sensor reproducibility (~5%) and long-term stability (90% of its original activity retained after 4 weeks) when stored in 50 mM phosphate buffer at pH 7 at 4 ${^{\circ}C}$.

• Archives of Pharmacal Research
• /
• v.28 no.7
• /
• pp.866-874
• /
• 2005

The objective of this study was to elucidate the feasibility to improve the solubility and bioavailability of poorly water-soluble itraconazole via solid dispersions by using supercritical fluid (SCF). Solid dispersions of itraconazole with hydrophilic polymer, HPMC 2910, were prepared by the aerosol solvent extraction system (ASES) under different process conditions of temperature/pressure. The particle size of solid dispersions ranged from 100 to 500 nm. The equilibrium solubility increased with decrease (15 to 10 MPa) in pressure and increase (40 to $60^{\circ}C$) in temperature. The solid dispersions prepared at $60^{\circ}C$/15 MPa showed a slight increase in equilibrium solubility (approximately 27-fold increase) when compared to pure itraconazole, while those prepared at $60^{\circ}C$/10MPa showed approximately 610-fold increase and no endothermic peaks corresponding to pure itraconazole were observed, indicating that itraconazole might be molecularly dispersed in HPMC 2910 in the amorphous form. The amorphous state of itraconazole was confirmed by DSC/XRD data. The pharmacokinetic parameters of the ASES-processed solid dispersions, such as $T_{max},\;C_{max},\;and\;AUC_{0-24h}$ were almost similar to $Sporanox_{\circledR}$ capsule which shows high bioavailability. Hence, it was concluded that the ASES process could be a promising technique to reduce particle size and/or prepare amorphous solid dispersion of drugs in order to improve the solubility and bioavailability of poorly water-soluble drugs.

• Journal of the Korean Vacuum Society
• /
• v.7 no.4
• /
• pp.306-313
• /
• 1998

The electrochromic $WO_3$thin films were prepared by using the electron-beam evaporatin technique. Flms prepared at a vacuum pressure of $10^{-4}$ mbar were found to be most stable during repeated potential cycles. The chemical stability of the film in aqueous solutions was also affected by the vacuum pressure during evaporation. The redox current and the optical properties of the degraded films were affected by the thickness of the film. The 5,000$\AA$-thick films were found to be most stable, undergoing the least degradation during the repeated coloring and bleaching cycles. The origin of the mechanism dominating the degradation during the repeated coloring and bleaching cycles was the accumulation of lithium in the film, which results in decreasing redox current. Tungsten oxide films with titanium content of about 10-15 mol% was found to be most stable, undergoing the least degradation during the repeated cycles. The origin of the mechanism dominating the least degradation during the repeated cycles was the reduction of lithium ion trapping sites in the films, which results in a increased durability.

• Membrane Journal
• /
• v.11 no.3
• /
• pp.109-115
• /
• 2001

Pore-filled ion-exchange membranes in which polypropylene(PP) microporous membrane was used as a nascent membrane were prepared by an in-situ cross-linking technique. Poly(vinylbenzyl chloride)(PVBCI) reacted with piperazine(PIP) or 1,4-diaminobicyclo[2,2,2]octane(DABCO) in a di-methylforamide(DMF) solution was filled in the pores of the microporous base membrane. After gellation the remaining chloromethyl groups were, then reacted with an amine such as trimethylamine to form positively charged, ammonium site. This will produce the pore-filled anion-exchange membrane. It was shown that this simple 2 step procedure gave dimensionally stable, pore-filled membranes in which the MG of polymer gel and degree of cross-linking could be easily controlled by the concentration of PVBCI and cross-linker in the starting DMF solution. Specially, high water permeability (7.8 kg/$m^2$hr, host membrane: PP3, MG: 73%, degree of cross-linking: 10%, crosslinker: PIP) at ultra low pressure(100 kPa) indicates the produced pore-filled membranes is usable as a water softening membrane.

• Asian Journal of Atmospheric Environment
• /
• v.2 no.2
• /
• pp.102-108
• /
• 2008

In China, energy and environmental problems are becoming serious owing to rapid economic development. Coal is the most problematic energy source because it causes indoor and outdoor air pollution, acid rain, and global warming. One type of clean coal technology that has been developed is the coal-biomass briquette (or bio-briquette, BB) technique. BBs, which are produced from pulverized coal, biomass (typically, agricultural waste), and a sulfur fixation agent (slaked lime, $Ca(OH)_2$) under high pressure without any binder, have a high sulfur-fixation effect. In addition, BB combustion ash, that is, the waste material, can be used as a neutralization agent for acidic soil because of its high alkalinity, which originates from the added slaked lime. In this study, we evaluated the suitability of alternative biomass sources, namely, aquatic plants, as a BB constituent from the perspective of their use as a source of energy. We selected three types of aquatic plants for use in BB preparation and compared the fuel, handling, and environmental characteristics of the new BBs with those of conventional BBs. Our results showed that air-dried aquatic plants had a higher calorific value, which was in proportion to their carbon content, than agricultural waste biomass; the compressive strength of the new BBs, which depends on the lignin content of the biomass, was high enough to bear long-range intracontinental transport in China; and the new BBs had the same emission control capacity as the conventional BBs.