• 한국전기전자재료학회논문지
• /
• 제19권1호
• /
• pp.52-57
• /
• 2006

Precision thin film resistors using evanohm R alloy were fabricated by do magnetron sputtering method. The physical and electrical properties of the resistors were studied after treatment of thermal annealing. The crystallization of the film was increased as the annealing temperature increase. Diffusion and oxidation of Cr and Al elements were occurred into the film surface. The minimum TCR values of 10.46 ppm/$^{\circ}C$ and 10.65 ppm/$^{\circ}C$ were measured at the annealing temperatures of $200^{\circ}C$ and $300^{\circ}C$, respectively. We are conducting additional studies to improve characteristics of our resistors for practical device application.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 하계학술대회 논문집 C
• /
• pp.1236-1238
• /
• 1994

TiAlN thin films were prepared by a multi target r.f magnetron sputtering system under different conditions. We have investigated the resistivity and T.C.R. (Temperature Coefficient of Resistance) characteristics of TiAlN films deposited on $Al_2O_3$ and glass substrates by sputtering in an $Ar:N_2$ gas mixture. We used Al and Ti metal as Target Material and $Ar:N_2$ gas as working gas. We varied the partial pressure ratio of $N_2/Ar$ from 0.2/7 to 1.0/6.2 (SCCM). And the R.F power of Ti and Al Target also were varied as 160/240, 200/200 and 240/160(W). In this experiment, we can get the precision thin film resistor with a very low T.C.R. (Temperature Coefficient of Resistance) below 25 ppm ${\Omega}/^{\circ}C$.

• 한국전기전자재료학회논문지
• /
• 제14권4호
• /
• pp.328-335
• /
• 2001

In this work, we made the precision thin film resistors of NiCr alloy (74wt%Ni-f18wt%Cr-4wt%Al-4wt%Cu) using DC/RF magnetron sputtering method and studied the sheet resistance and TCR(Temperature Coefficient of Resistance) etc... of the Ni-Cr-Al-Cu alloy thin film according to the change by annealing treatment to 400$\^{C}$ in air and nitrogen atmosphere and the change(power, pressure, substrate temperature) of sputtering process.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.913-917
• /
• 2003

In the electronic components and devices fabrication, thin film resistors with low TCR(temperature coefficient of resistance) and high precision have been used over 3 GHz microwave in recent years. Ni-Cr alloys thin films resistors is one of the most commonly used resistive materials because it has low TCR and highly stable resistance. In this work, we fabricated thin film resistors using Evanohm alloys target(72Ni-20Cr-3Al-4Mn-Si) of s-type with excellent resistors properties by RF-sputtering. Also we reported best deposited conditions of thin film resistors for microwave to observe microstructure and electronic properties of thin film according to deposited conditions(between target and substrate, power supply)

• 한국전기전자재료학회논문지
• /
• 제20권6호
• /
• pp.520-526
• /
• 2007

In order to acquire fundamental informations to fabricate high precision thin film resistors, NiCr/NiCrSi alloy films were prepared using Ni and Cr targets. Effect of composition on the electrical properties of the NiCr/NiCrSi alloy film were then investigated. Considering the effect of Si doping on the electrical and material characteristics, the lower TCR (temperature coefficient of resistance) values could be achieved for samples with Ni/Cr ratio of $0.8{\sim}1.5$ (in a range of relative higher specific resistivity and Cr composition of $40\;wt%{\sim}55\;wt%$) and with Si doping. Consequently, the sample prepared using a DC power showed a good TCR of $-25\;ppm/^{\circ}C$, which implies that increase of specific resistivity and decrease of TCR would be achieved more efficiently not for Ni-Cr binary material but for Si doped Ni-Cr ternary material, and not using RF power but using DC power in the sputtering process.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 추계학술대회 논문집 Vol.15
• /
• pp.411-415
• /
• 2002

Precision resistors were prepared by controlling the concentration of Ni and Cr deposited on cylindrical alumina substrates (diameter: 1.7mm, length: 5.5mm). Deposited films were analyzed with FESEM, AES, and AFM. As the amount of Cr in the film increases, the TCR was shifted to negative direction.

• 마이크로전자및패키징학회지
• /
• 제11권1호
• /
• pp.37-42
• /
• 2004

최근에 3 ㎓이상의 고주파용 전자부품과 소자의 제조에 낮은 저항온도계수(TCR)값과 높은 정밀도를 갖는 박막저항이 사용되고 있다. Ni-Cr 박막저항은 낮은 TCR 값과 저항에 대한 높은 안정성 때문에 저항 물질로 사용되는 가장 일반적인 물질이다. 본 연구에서는 $Ni_{72}Cr_Al_3Mn_4Si$(wt%)이 첨가된 우수한 저항특성을 갖는 S-type의 Evanohm 합금 타겟과 스퍼터링 장비를 이용하여 박막 저항을 제조하였다. 또한 열처리 조건을 $200^{\circ}C$, 300$300^{\circ}C$, $400^{\circ}C$, $500^{\circ}C$로 변화시키면서 고주파 박막 저항의 미세구조와 전기적 특성을 관찰하여 최상의 열처리 조건을 알아보았다.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2003년도 기술심포지움 논문집
• /
• pp.145-150
• /
• 2003

최근에 3 GHz이상의 고주파용 전자부품과 소자의 제조에 낮은 TCR 값과 높은 정밀도를 갖는 박막저항이 사용되고 있다. Ni-Cr 박막저항은 낮은 TCR 값과 저항에 대한 높은 안정성 때문에 저항 물질로 사용되는 가장 일반적인 물질이다. 본 연구에서는 $Ni_{72}Cr_{20}Al_3Mn_4Si(wt\%)$ 첨가된 우수한 저항특성을 갖는 s-type의 Evanohm 합금 타겟과 스퍼터링 장비를 이용하여 박막 저항을 제조하였다. 또한 열처리 조건을 $200^{\circ}C,\;300^{\circ}C,\;400^{\circ}C,\;500^{\circ}C$로 변화시키면서 고주파 박막저항의 미세구조와 전기적 특성을 관찰하여 최상의 열처리 조건을 알아보았다.