• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2004년도 학술대회지
• /
• pp.628-635
• /
• 2004

The characteristic of thin film resistor with low TCR( temperature coefficient of resistance ) and high precision are studied. The thin film resistor for 1/4W was fabricated and characteristic of these resistors was investigated. The fabricated device had the thickness of $2.48{\leqq}$ and the resistivity of $0.27{\omega}mm$. The electrical characteristic was evaluated by HP 4339B and 4284A instruments with HP l6339A. The profile of trimmed structure was also measured by non contact interferometer. The change of resistance and TCR increased with increasing roughness and resistance. To reduce the effect of stress annealing treatment was performed in the range of 563 to 623 K after trimming. The characteristic was improved after annealing. It is expected the fabricated device can be useful for high precision and low TCR. Fabricated thin film resistor has average deviation of resistance less than $0.35{\%}$ and TCR within 60.60ppm/K.

• 한국전기전자재료학회논문지
• /
• 제35권3호
• /
• pp.269-274
• /
• 2022

We prepared carbon nanotube (CNT) paper by a vacuum filtration method for the use of a chip-typed resistor as a precision passive device with a constant resistance. Hybrid resistor composed of the CNT resistor with a negative temperature coefficient of resistance (T.C.R) and a metal alloy resistor with a positive T.C.R could lead to a constant resistance, because the resistance increase owing to the temperature increase at the metal alloy and decrease at the CNT could counterbalance each other. The constant resistance for the precision passive devices should be maintained even when a heat was generated by a current flow resulting in resistance change. Performance reliabilities of the CNT resistor for the precision passive device applications such as electrical load limit, environmental load limit, and life limit specified in IEC 60115-1 must be ensured. In this study, therefore, the rated power determination and T.C.R tests of the CNT paper were conducted. -900~-700 ppm/℃ of TCR, 0.1~0.2 A of the carrying current capacity, and 0.0625~0.125 W of the rated power limit were obtained from the CNT paper. Consequently, we confirmed that the application of CNT materials for the precision hybrid passive devices with a metal alloy could result in a better performance reliability with a zero tolerance.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권1호
• /
• pp.13-20
• /
• 1995

To develope a high precision TiAIN thin film resistor, TiAIN films were deposited on A1$_{2}$03 substrates by reactive planar magnetron cosputtering from Ti and Al targets in an Ar-N$_{2}$ atmosphere. The characteristics of the TiAIN thin film were controlled by changing of the R.F. power on Ti and Al targets, and the N$_{2}$ partial pressure. The high precision TiAIN thin film resistor with TCR(Temperature Coefficient of Resistance) of less than 10ppm/.deg. C was obtained under the R.F. power condition of 160(w)/240(w) to Ti and Al targets at the N$_{2}$ partial pressure of 7*10$^{-5}$ Torr. The composition of these films were investigated by XRD, SEM and EDS.

• Journal of Electrical Engineering and Technology
• /
• 제2권4호
• /
• pp.525-531
• /
• 2007

Ni(75 wt.%)-Cr(20 wt.%)-Al(3 wt.%)-Mn(4 wt.%)-Si(1 wt.%) alloy thin films were prepared using the DC magnetron sputtering process by varying the sputtering conditions such as power, pressure, substrate temperature, and post-deposition annealing temperature in order to fabricate a precision thin film resistor. For all the thin film resistors, sheet resistance, temperature coefficient of resistance (TCR), and crystallinity were analyzed and the effects of sputtering conditions on their properties were also investigated. The oxygen content and TCR of Ni-Cr-Al-Mn-Si resistors were decreased by increasing the sputtering pressure. Their sheet resistance, TCR, and crystallinity were enhanced by elevating the substrate temperature. In addition, the annealing of the resistor thin films in air at a temperature higher than $300^{\circ}C$ lead to a remarkable rise in their sheet resistance and TCR. This may be attributed to the improved formation of NiO layer on the surface of the resistor thin film at an elevated temperature.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 추계학술대회 논문집
• /
• pp.175-176
• /
• 2006

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2007년도 춘계학술대회 논문집
• /
• pp.757-758
• /
• 2007

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 추계학술대회 논문요약집
• /
• pp.134-134
• /
• 2003

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2011년도 춘계학술대회 논문집
• /
• pp.145-146
• /
• 2011

• 한국전기전자재료학회논문지
• /
• 제30권6호
• /
• pp.376-380
• /
• 2017

In this paper, we prepared a metal alloy resistor with stable thermal electro motive force (thermal EMF) as well as a low temperature coefficient of resistance (TCR) by adjusting the manganese proportion from 3 to 12 wt% in the Cu-Mn-Ni alloy. Composition of the fabricated metal alloy was investigated using energy dispersive X-ray (EDX) analysis. The TCR of each sample was measured as 44.56, 40.54, 35.60, and 31.56 ppm for Cu-3Mn-2Ni, Cu-5Mn-2Ni, Cu-10Mn-2Ni, and Cu-12Mn-2Ni, respectively. All the resistor samples were available for the F grade (${\pm}1%$ of the allowable error of resistance) high-precision resistor. All the samples satisfied the baseline of high thermal EMF (under 3 mV at $60^{\circ}C$); however, Cu-3Mn-2Ni and Cu-5Mn-2Ni satisfied the baseline of low thermal EMF (under 0.3 mV at $25^{\circ}C$). We were thus able to design and fabricate the metal alloy resistor of Cu-3Mn-2Ni and Cu-5Mn-2Ni to have low TCR and stable thermal EMF at the same time.

• 전기의세계
• /
• 제22권4호
• /
• pp.7-10
• /
• 1973

The characteristics of all the instruments and materials used in atomic industry is changed due to radiation damages by the effects of radiation activities. In this study, when the Carbon Resistor, main element of electrical circuits, is irradiated by Gamma-Ray, variations in its electrical properties have been investigated. The following results are obtained: 1) The resistance value in Carbon Resistor is exponentially increased as the quantity of irradiation by Gamma-Ray is increased, but in case of more than 10$^{6}$ R/hr. of quantity of irradiation it has saturated-state value. 2) The rate of change inrestistance value has been independent on the intensity of Gamma-Ray source when Carbon Resistor is irradiated in the same quantity of irradiation. 3) The resistance value in irradiated Carbon Resistor has not been varied with elapse of time. 4) The more the distance from the Carbon Resistor to the Gamma-Ray source the more greatly the resistance value is decreased and that it has been shown that the more quantity of irradiation by Gamma-Ray, the greater the rate of decrease in resistance value. Through the above results it has been concluded that the measurement values obtained by the high-precision instruments in the radiation field have to be corrected with proper consideration to radiation damages.