• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.182.2-182.2
• /
• 2015

최근 학계나 산업계에서 투명 전자 소자에 대하여 활발한 연구가 진행되면서, 투명 전 도성 산화물(TCO: transparent conductive oxide)에 대한 관심이 높아지고 있다. 대표적인 TCO 물질인 Indium Tin Oxide (ITO)는 가시 광 영역에서의 높은 투과 및 높은 도전성을 가져 전압을 인가하면 발열이 가능하므로 이를 투명 면상 발열체에 적용시키는 연구가 활발히 진행되고 있다. 하지만, ITO는 발열 테스트 결과 온도가 상승함에 따라 발열이 일부분에 집중되는 현상이 있으며, 전도성을 높이기 위하여 추가공정이 필요하다. 또한, 글라스의 곡면 부분에서 ITO를 사용하면 유연성이 부족하므로 크랙이 발생한다는 단점이 있다. 따라서, 최근 Silver nanowire (AgNW), Single-walled Carbon nanotube (SWCNT), ITO를 기반으로 한 AgNW에 ITO를 증착 하거나 SWCNT를 코팅하여 우수한 전기적, 광학적 특성을 지닌 하이브리드 전극이 투명 면상 발열체 재료로서 사용되고 있다. 하지만 대체된 재료들도 다양한 문제점을 가지고 있다. 예를 들어 고온에서 발열을 유지하지 못하고 끊어지거나 가시광영역의 투과율이 낮은 점 등이 있다. 이런 다양한 문제점들을 보완 할 수 있는 새로운 투명 면상 발열체에 적용한 연구가 요구되고 있다. 본 연구에서는 GZO/Ag/GZO 하이브리드 구조의 투명 면상 발열체를 제작하여 전기적, 광학적 특성을 비교하고 발열량, 온도 균일 성, 발열 유지 안정도를 확인하였다. 본 연구에서는 $50{\times}50mm$ 크기의 Non-alkali glass (삼성코닝 E2000) 기판 상에 DC마그네트론 스퍼터링 공정을 이용하여 상온에서 GZO, Ag, GZO 박막을 연속적으로 증착 하여 다층구조의 하이브리드형 투명 면상 발열체를 제조하였다. 박막 증착 파워는 DC (Ag) power 50 W, RF (GZO) power 200 W로 하였으며 GZO박막두께는 45 nm로 고정 시키고 Ag박막 두께는 5~20 nm로 변화를 주었다. 증착원은 3인치 GZO 세라믹 타깃 (2.27 wt. % Ga2O3) 과 Ag 금속 타깃 (순도 99.99%)을 사용하였으며, Ar을 40 sccm 주입 후 Working pressure는 고 순도 Ar을 사용하여 1.0 Pa로 고정하며 10분간 Pre-sputtering을하고 증착을 진행하였다. 앞선 실험을 통해 증착한 박막의 전기적, 광학적 특성은 각각 Hall-effect measurements system (ECOPIA, HMS3000), UV-Vis spectrophotometer (UV-1800, Shimadzu)를 사용해 측정 되었으며, 하이브리드 표면의 구조 및 형상은 FESEM으로 관찰하였다. 또한 표면온도 측정기infrared camera (IR camera)를 이용하여 4~12 V/cm의 전압을 인가 시 시간에 따른 투명 면상 발열체의 표면 온도변화를 관찰하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제31권3호
• /
• pp.263-271
• /
• 2007

The heat transfer coefficient and pressure drop during 9as cooling process of $CO_2$ (R744) in a helically coiled copper tube with the inner diameter of 4.55 mm and outer diameter of 6.35 mm were investigated experimentally. The main components of the refrigerant loop are a receiver, a variable-speed pump. a mass flow meter a pre-heater and a helically coiled type gas cooler (test section). The refrigerant mass fluxes are varied from 200 to $800kg/m^2s$ and the inlet pressures of gas cooler are 7.5 to 10.0 MPa. The heat transfer coefficients of $CO_2$ in a helically coiled tube are higher than those in a horizontal tube. The Pressure drop of $CO_2$ in the gas cooler shows a relatively good agreement with those predicted by Ito's correlation developed for single-phase in a helically coiled tube. The local heat transfer coefficient of $CO_2$ agrees well with the correlation by Pitla et al. However. at the region near pseudo-critical temperature. the experiments indicate higher values than the Pitla et al correlation. Therefore, various experiments in helically coiled tubes have to be conducted and it is necessary to develop the reliable and accurate prediction determining the heat transfer and pressure drop of $CO_2$ in a helically coiled tube.

• 대한환경공학회지
• /
• 제38권3호
• /
• pp.128-134
• /
• 2016

S 매립장 매립가스 발전시설을 대상으로 발전량에 미치는 주요 요소와 그 영향도를 분석하였다. 50 MWh 24시간의 정상가동 일수는 2007년부터 2014년까지의 총 운전기간 일수대비 70.9%이었으며, 실제 생산한 전력은 이론적인 최대 발전 가능량 3,428,400 MW의 79.3%이었다. 발전효율에 영향을 미치는 주요 요소는 정기점검 등이 44.0%, 황화수소로 인한 감축운전이 37.4% 그리고 공기예열기 세정 18.6% 순이었다. 그러나 황화수소 감축운전 기간이 2년인 점을 감안하면 고농도 황화수소 발생이 매립가스 발전에 가장 큰 영향을 미치고 있었다. 장기적인 발전 가능량 분석결과 매립종료 해인 2018년 35.9 MWh 이었으며 이후 지속적으로 감소하여 2028년 16.6 MWh, 2038년에는 8.4 MWh 이하가 될 것으로 예측되었다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권3호
• /
• pp.500-508
• /
• 2004

The heat transfer coefficients during gas cooling process of carbon dioxide in a horizontal tube were investigated. The experiments are conducted without oil in the refrigerant loop. The main components of the refrigerant loop are a receiver, a variable-speed pump, a mass flow meter, a pre-heater, and a gas cooler(test section). The water loop consists of a variable-speed pump, an isothermal tank, and a flow meter. The gas cooler is a counterflow heat exchanger by cooled water flowing in the annulus. The $CO_2$ flows in the horizontal stainless steel tube. which is 9.53mm in O.D. and 7.75mm in I.D. The gas cooler is 6 [m] in length. which is divided into 12 subsections, respectively. The experimental conditions considered in the study are following range of variables : refrigerant temperature is between 20 and $100^{\circ}C$. mass fluxes ranged from 200 to 400kg/($m^2$.s), average pressure varied from 7.5 to 10.0MPa. The main results were summarized as follows : The friction factors of $CO_2$ in the gas cooler show a relatively good agreement with those predicted by Blasius' correlation. The local heat transfer coefficient in the gas cooler has compared with most of correlations, which are the famous ones for forced convection heat transfer of turbulent flow. The results show that the local heat transfer coefficient of gas cooler agrees well with the correlation by Bringer-Smith except that at the region near pseudo critical temperature. while that at the near pseudo critical temperature is higher than the correlation.

• Journal of Advanced Marine Engineering and Technology
• /
• 제31권6호
• /
• pp.699-706
• /
• 2007

The cooling heat transfer coefficient and pressure drop of $CO_2$(R-744) in helical coil copper tubes were investigated experimentally The main components of the refrigerant loop are a receiver, a variable-speed pump, a mass flow meter. a pre-heater and a inclined helical coil type gas cooler (test section). The test section consists of a smooth copper tube of 2.45 and 4.55mm inner diameter The refrigerant mass fluxes were varied from 200 to $600 [kg/m^2s]$ and the inlet pressures of 9as cooler were 7.5 to 10.0 [MPa]. The heat transfer coefficients of $CO_2$ in helical coil tubes increase with the increase of mass flux and gas cooling pressure of $CO_2$. The pressure drop of $CO_2$ in the gas cooler shows a relatively food agreement with those Predicted by Ito's correlation developed for single-phase in helical coil tubes. Though a few correlation available with the data. the local heat transfer coefficient of $CO_2$ agrees well with those presented by Pitla et al. among the predictions. However at the region near pseudo-critical temperature. the experiment data indicate higher values than the Pitla et al. correlation.

• Journal of Advanced Marine Engineering and Technology
• /
• 제31권6호
• /
• pp.707-714
• /
• 2007

The heat transfer coefficient and Pressure drop during gas cooling process of $CO_2$ (R-744) in inclined helical coil copper tubes were investigated experimentally. The main components of the refrigerant loop are a receiver. a variable-speed pump. a mass flow meter, a pre-heater and a inclined helical coil type gas cooler (test section). The test section consists of a smooth copper tube of 2.45mm inner diameter. The refrigerant mass fluxes were varied from 200 to $600[kg/m^2s]$ and the inlet Pressures of gas cooler were 7.5 to 10.0 [MPa]. The heat transfer coefficients of $CO_2$ in the inclined helical coil tubes increases with the increase of mass flux and gas cooling pressure of $CO_2$. The pressure drop of $CO_2$ in the gas cooler shows a relatively good agreement with those Predicted by Ito's correlation developed for single-phase in a helical coil tube. The local heat transfer coefficient of $CO_2$ agrees well with the correlation by Pitla et al. However, at the region near pseudo-critical temperature. the experiments indicate higher values than the Pitla et al. correlation. Therefore. various experiments in the inclined helical coil tubes have to be conducted and it is necessary to develop the reliable and accurate prediction determining the heat transfer and pressure drop of $CO_2$ in the inclined helical coil tubes.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 전기학술대회논문집
• /
• pp.189-194
• /
• 2005

The evaporation heat transfer and pressure drop of $CO_2$ in a small diameter tube was investigated experimentally. The experiments were conducted without oil in a closed refrigerant loop which was driven by a magnetic gear pump. The main components of the refrigerant loop are a receiver, a variable-speed pump, a mass flow meter, a pre-heater and evaporator(test section). The test section was made of a horizontal stainless steel tube with the inner diameter of 4.57 mm, and length of 4 m. The experiments were conducted at mass flux of 200 to 700 $kg/m^2s$, saturation temperature of $0^{\circ}C$ to $20^{\circ}C$, and heat flux of 10 to 20 $kW/m^2$ . The test results showed the evaporation heat transfer of $CO_2$ has great effect on more nucleate boiling than convective boiling. The evaporation heat transfer coefficients of $CO_2$ are highly dependent on the vapor quality, heat flux and saturation temperature. The evaporation pressure drop of C02 are highly dependent on the mass flux. In comparison with test results and existing correlations, correlations failed to predict the evaporation heat transfer coefficient and pressure drop of $CO_2$, therefore, it is necessary to develop reliable and accurate predictions determining the evaporation heat transfer coefficient and friction pressure drop of $CO_2$ in a horizontal tube.

• 한국자원리싸이클링학회:학술대회논문집
• /
• 한국자원리싸이클링학회 2004년도 춘계임시총회 및 제23회 학술대회
• /
• pp.109-113
• /
• 2004

본 연구에서는 현재 농촌 지역에서 광범위하게 사용되고 있으나 거의 재활용이 안 되어 방치상태에 있는 농업용 폐비닐을 이용하여 시멘트 제조를 위한 고형 연료를 제작할 수 있는 이동식 장치를 개발하려 하였다. 이를 위해 재생연료의 연소 특성 및 2차 오염 발생여부에 대해 조사했으며, 1cm 이하 알갱이 형태의 고형 연료를 제조 가능한 이동식 장치를 개발하였다. 또한 기존의 시멘트 예열탑에서의 투입 방식에서 벗어나, main burner에 적용기술 개발을 통해, NOx 및 O2 발생량의 감소가 나타났고, 0.5ton/hour 투입 시, 0.2-0.3ton/hour 정도 Coal량이 감소하는 연료 단가 절감 효과를 얻을 수 있었다.

• 한국자동차공학회논문집
• /
• 제16권3호
• /
• pp.30-37
• /
• 2008

The evaporation pressure drop of $CO_2$ (R-744) in horizontal tubes was investigated experimentally. The experiments were conducted without oil in a closed refrigerant loop which was driven by a magnetic gear pump. The main components of the refrigerant loop are a receiver, a variable-speed pump, a mass flow meter, a pre-heater and evaporator (test section). The test section consists of a smooth, horizontal stainless steel tube of 7.75 and 4.57 mm inner diameter. The experiments were conducted at saturation temperature of $-5^{\circ}C\;to\;5^{\circ}C$, and heat flux of 10 to $40kW/m^2$. The test results showed the evaporation pressure drop of $CO_2$ are highly dependent on the vapor quality, heat flux and saturation temperature. The pressure drop measured during the evaporation process of $CO_2$ increases with increased mass flux, and decreases as the saturation temperature increased. The evaporation pressure drop of $CO_2$ is very lower than that of R-22. In comparison with test results and existing correlations, the best fit of the present experimental data is obtained with the correlation of Choi et al. But existing correlations failed to predict the evaporation pressure drop of $CO_2$. Therefore, it is necessary to develop reliable and accurate predictions determining the evaporation pressure drop of $CO_2$ in a horizontal tube.

• 대한기계학회논문집B
• /
• 제25권10호
• /
• pp.1318-1326
• /
• 2001

The evaporation heat transfer coefficient and pressure drop for refrigerant R-22 flowing in the plate and shell heat exchanger were investigated experimentally in this study. Two vertical counterflow channels were farmed in the exchanger by three plates of commercial geometry with a corrugated trapezoid shape of a chevron angel of 45 ° Upflow boiling of refrigerant R-22 in one channel receives heat from the hot downf1ow of water in the other channel. The effects of the mean vapor quality, mass flux, heat flux and pressure of R-22 on the evaporation heat transfer and pressure drop were explored. The quality change of R-22 between the inlet and outlet of the refrigerant channel ranges from 0.03 to 0.05. The present data showed that both the evaporation heat transfer coefficient and pressure drop increase with the vapor quality. At a higher mass flux, the evaporation heat transfer coefficient and pressure drop are higher for the entire range of the vapor quality Raising the imposed wall heat flux was found to slightly improve the heat transfer, while at a higher refrigerant pressure, both the heat transfer and pressure drop are slightly lower.