• 한국농공학회논문집
• /
• 제58권6호
• /
• pp.71-77
• /
• 2016

This study was to evaluate the feasibility of pre-consolidation pressure distribution characteristic of western and southern coastal region, using correlation of unconfined compressive strength and preceding research equation. Pre-consolidation of western and southern region showed similar trends undrained shear strength and pre-consolidation pressure in proportion to unconfined compressive strength. Predicted results of U.S. NAVY. (1982) equation revealed a small error western 9.7 % and southern 0.4 %. Prediction correlation results of pre-consolidation using unconfined compressive strength revealed an error western 16.8 % and southern 0.7 %. It was reported that less than 20 percent of pre-consolidation pressure prediction result of Casagrande forecasting error. Estimates of pre-consolidation pressure are possible, before the standard consolidation test, because it was reported that less than 20 % of the forecasting errors of Casagrande.

• 한국농공학회지
• /
• 제18권4호
• /
• pp.4242-4250
• /
• 1976

The determination of the pre-consolidation load known to have a great effect on the consolidation characteristics of the soil have been researched and discussed in detail by many other researchers. A study was undertaken to investigate and compare the effect of pre-consolidation loads on the coefficient of permeability and the consolidation characterisics of soil through the consolidation test on the three types of soil samples. The results of this study are follows; 1. Large compression index is dependent on initial void ratio of the sample being used and the pressure-void ratio curve shows a curved linear relationship in over-consolidated area but a linear relationship in normally consolidated area.2. Settlement-time curve is S-shaped where the pressure is larger than pre-consolidation load and regardless of over-burden pressure, it is a similar straight line respectively in the secondary consolidation area. 3. Primary consolidation ratio of the sample increases almost linearly with the increase of over-burden pressure but the coefficient of volume compressibility decreases linearly with the increase of it. 4. Time factor of a certain degree of consolidation increases with over-burden pressure but the coefficient of consolidation decreases with it in over-consolidated area. There is a linear relationship between them in normally consolidated area. 5. The void ratio of completion point of primary consolidation decreases linearly with over-burden pressure. 6. The coefficient of permeability of sample decreases linearly with over-burden pressure in normally consolidated area, also it increases linearly with increment of the void ratio of the sample.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.91-96
• /
• 2000

Glass fiber reinforced thermoplastic composites were manufactured by Rapid Press Consolidation Technique(RPCT) as functions of temperature, pressure and time in pre-heating, consolidation and solidification sections during the manufacturing processing. It was found that the material property is greatly affected by pre-heating temperature under vacuum, mold temperature and molding pressure. Among them, the temperature In the mold was the most critical factor in determining the mechanical properties and the molded conditions of specimen. The crystallinity of PET matrix was also investigated by differential scanning calorimetry(DSC) measurements for various processing conditions. The level of crystallinity($X_c$) depended strongly on the mold temperature, cooling rate and the type of composite. The difference in $X_c$ is believed to be one of important factors in characterizing the mechanical properties.

• 지질공학
• /
• 제12권4호
• /
• pp.459-469
• /
• 2002

재성형된 해성점토 시료를 연직·수평방향으로 채취하여 표준압밀시험(SCT)과 일정변형률속도 압밀시험(CRSC)을 실시하여 연약 해성점토지반에 대한 압밀정수들의 구성관계를 확인하였다. 또한, 불교란 교란 화강암질 풍화토의 표준·일정변형률속도 압밀시험을 통하여 화강암질 풍화토에 대한 압밀 정수들의 특성과 적용성을 고찰하였다. 그 결과 해성점토 시료의 연직·수평방향과 표준·일정변형률속도압밀시험 방법에 따라 선행압밀응력, 압축지수, 과잉간극수압, 간극수압비 등이 달리 산정됨을 알 수 있었다. 또한, 불교란·교란 화강암질 풍화토 시료에서도 해성점토와 유사하게 과압밑·정규압밀 구간에서 압밀정수들의 변화를 확인하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1992년도 가을학술발표회 논문집
• /
• pp.113-120
• /
• 1992

The construction of container terminal at Brani, Singapore required the improvement of soft clay layer having the thickness of about 6.5m, average moisture content of 79.4%, liquid limit of 90.4%, plastic limit of 21.8%, field vane strength of 10 to 25 KPa, pre-consolidation pressure of 225 to 60 KPa and compression index of 0.4 to 1.0. For the improvement of this layer, Colbon drains of 1.3m spacing in triangular pattern were installed to the bottom of the layer and surcharge of more than 11.25m high sand fill was later applied to the treated area. The settlement and lateral displacement of the ground were measured and the speed of surcharge filling was controlled, based on these readings. The removal of surcharge was determinied using the estimated time for the 90% degree of consolidation under the design pressure of 180KPa. The field and laboratory test results show that the soft clay layer has been improved substantially in its strength and consolidation characteristics: increase in strength of about 50KPa and pre-consolidation pressure and decrease in void ratio and compression index.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 추계학술대회 논문집
• /
• pp.504-507
• /
• 2002

Glass fiber reinforced PET (Poly-Ethylene-Terephthalate) matrix composite was manufactured by rapid press consolidation technique as functions of temperature, pressure and time in pre-heating, consolidation and solidification stages. The optimal manufacturing conditions for this composite were discussed based on the void content, tensile, interlaminar shear, and impact properties. A tensile test was attempted to investigate the mechanical properties of the composite. It is found that the level of crystallinity and microstructure affects on the tensile properties substantially.

• Geomechanics and Engineering
• /
• 제1권3호
• /
• pp.179-191
• /
• 2009

For a two-way drainage deposit under a surcharge load, it is possible to leave a layer adjacent to the bottom drainage boundary without prefabricated vertical drain (PVD) improvement and achieve approximately the same degree of consolidation as a fully penetrated case. This depth is designated as an optimum PVD installation depth. Further, for a two-way drainage deposit under vacuum pressure, if the PVDs are fully penetrated through the deposit, the vacuum pressure will leak through the bottom drainage boundary. In this case, the PVDs have to be partially penetrated, and there is an optimum installation depth. The equations for calculating these optimum installation depths are presented, and the usefulness of the equations is studied by using finite element analysis as well as laboratory model test results.

• 대한기계학회논문집A
• /
• 제26권5호
• /
• pp.813-821
• /
• 2002

Glass fiber reinforced PET matrix composite was manufactured by rapid press consolidation technique as functions of temperature, pressure and time in pre-heating, consolidation and solidification stages. The optimal manufacturing conditions for this composite were discussed based on the void content, tensile, interlaminar shear and impact properties. In addition, the levels of crystallinity with various manufacturing conditions were measured using differential scanning calorimetry to investigate the mechanical properties of this composite material as a function of crystallinity. Among many processing parameters, the mold temperature and the cooling rate after forming were found to be the most critical factors in determining the level of crystallinity and mechanical properties. The level of crystallinity affects the tensile properties to some degree. However, impact properties are affected much more. It also affects the degree of ductility, which determines the impact energy of this material.

• 한국농공학회지
• /
• 제34권2호
• /
• pp.60-72
• /
• 1992

This study aims at predicting the behavior of saturated soft clayey foundation subjected to earth structure loads such as tidal dike, embankment etc. by using Biot's consolidation equation coupled with elasto-viscoplastic constitutive model. To validate the computer program developed b author, a case study was performed for the site of Kwang-yang steel works improved by sand drain, where since the beginning of the works, field measurements(settlement, lateral displacement and excess pore water pressure) had been accurately achieved. Comparisons between numerical results and observation values were carried out. The main results obtained are summarized as follows : 1. Settlement and lateral displacement between numerical and observation values show satisfactory accordance. 2. As for the exess pre water pressure, numerical results appear to be larger than observation values, which may be due to the existence of sand seams which were not found during soil investigation. 3. Useful data available for failure prediction of soft foundation can be secured by examining lateral displacement, settlement, exess pore water pressure and stress paths.

• 한국해양공학회지
• /
• 제5권1호
• /
• pp.35-44
• /
• 1991

This study was carried out for the purpose of pre-estimating long-term settlement under condition of actual field soil's property, in case of building up industrial sites on the marine deposit silty clay located at West Coast in Korea. This study analyzed Hyperbolic Method, Square Root Time Method and Exponential Function Method with utilization of measured survey values of settlement in In-Cheon Namdong Industrial Sites. In the future, for the continuos utilization, it seemed to be needed that further the survey values of fields should be accurartely measured for the analysis of more accurate pre-estimate about long-term settlement. Among the prediction methods of settlement Hyperbolic Method seemed to be the best fitting method for measured data. The settlement equations were derived from above three methods, for long-term settlements.