• 전자공학회논문지SC
• /
• 제48권6호
• /
• pp.71-81
• /
• 2011

일반적인 내연기관 자동차와는 달리, 전기자동차는 파워트레인을 구성하는 배터리, 인버터, 모터 등의 전기 동력 시스템들이 차량의 주행성능과 동역학 특성에 직접적인 영향을 준다. 따라서 전기 차량의 최종 운동 및 동특성을 예측하기 위해서, 기계 및 전기전자 복합 시스템을 세부적으로 모델링하고 이를 통한 전체 파워트레인의 해석이 필요하다. 본 논문에서는 전기자동차의 최종 출력 성능을 예측하고 분석하기 위한 전기자동차의 파워트레인 시스템의 동적 모델을 유도하였다. 전기적인 신호로부터 최종 기계 동력 시스템으로 전달되는 입출력 변수의 상관관계를 수학적으로 모델링하여 개발하였다. 또한, 전기자동차의 동특성을 시뮬레이션 할 수 있는 기준모델을 Matlab/Simulink 플랫폼 기반으로 개발하였으며, 이를 이용하여 유도된 수학적 분석 모델을 검증하였다. 이를 통하여 속도, 가속도, 추진력 등의 주요 차량 주행성능을 비교 분석하였다.

• 한국자동차공학회논문집
• /
• 제20권1호
• /
• pp.95-105
• /
• 2012

The selective catalytic reduction (SCR) system is a highly-effective aftertreatment device for NOx reduction of diesel engines. Generally, the ammonia ($NH_3$) was generated from reaction mechanism of SCR in the SCR system using the liquid urea as the reluctant. Therefore, the precise urea dosing control is a very important key for NOx and $NH_3$ slip reduction in the SCR system. This paper investigated NOx and $NH_3$ emission characteristics of urea-SCR dosing system based on model-based control algorithm in order to reduce NOx. In the map-based control algorithm, target amount of urea solution was determined by mass flow rate of exhaust gas obtained from engine rpm, torque and $O_2$ for feed-back control NOx concentration should be measured by NOx sensor. Moreover, this algorithm can not estimate $NH_3$ absorbed on the catalyst. Hence, the urea injection can be too rich or too lean. In this study, the model-based control algorithm was developed and evaluated on the numerical model describing physical and chemical phenomena in SCR system. One channel thermo-fluid model coupled with finely tuned chemical reaction model was applied to this control algorithm. The vehicle test was carried out by using map-based and model-based control algorithms in the NEDC mode in order to evaluate the performance of the model based control algorithm.

• 한국정밀공학회지
• /
• 제21권2호
• /
• pp.43-51
• /
• 2004

In this paper, the element combination algorithm for designing an arbitrary type of the automatic transmissions is proposed. The powertrain simulation software using this algorithm is then developed. The deliveries of the angular velocities and torques are only considered for the motion characteristics of the automatic transmissions. The effects of the vibration and noise are not considered. The automatic transmission is defined by the basic elements, i.e., planetary gear set, clutch, brake, shaft, general gear, and inertia. The transmission system is defined by the combination of these elements. The element combination matrices automatically generate the equations of motion for each shift. The self error-correcting algorithm is also developed to verify the element combination algorithm. This automotive powertrain simulation/design software with user-friendly graphic user interface has two main modules. The first module, the automatic powerflow generation module, mainly consists of the automatic powerflow and component generation algorithms. This paper covers the theory and application for the first module. The second module deals with the automatic system generation algorithm and will be discussed in the second paper.

• 한국자동차공학회논문집
• /
• 제21권5호
• /
• pp.67-73
• /
• 2013

This experimental work described the effect of flow control valve type on the performance of wobble plate type fuel pump for the stable DME fuel supply. In order to study this, different four types of flow control valves (ITV, SCV, IMV and MPROP) were installed on the wobble plate fuel pump, and fuel flow rate, torque, and temperature variation of pump were investigated under various operating conditions by using pump performance test system. It was revealed that wobble plate type fuel pump worked well with ITV and SCV control valve, and the flow rate and torque of fuel pump was in proportion to the value of valve open duty. The maximum flow rate and torque of fuel pump were achieved around the 50% duty of control valve. Temperature variation at all pump measuring points were under $60^{\circ}C$ which is acceptable.

• 한국자동차공학회논문집
• /
• 제20권6호
• /
• pp.107-116
• /
• 2012

In this study, the trucks(2.9-liter) have been developed to use DME as fuel, and performance test of the vehicle's DME engine, power, emissions, fuel economy and vehicle aspects was conducted. For experiments, the fuel system(common-rail injectors and high-pressure pump included) and the engine control logic was developed, and ECU mapping was performed. As a result, the rail pressure from 40MPa to approximately 65% increase compared to the base injector has been confirmed that. Also, the pump discharge flow is 15.5 kg/h when the fuel rail pressure is 400rpm(40MPa), and the pump discharge flow is 92.1 kg/h when the fuel rail pressure is 2,000rpm(40MPa). The maximum value of full-load torque capability is 25.5 kgfm(based on 2,000 rpm), and more than 90% compared to the level of the diesel engine were obtained. The DME vehicle was developed in this study, 120 km/h can drive to the stable, and calculated in accordance with the carbon-balance method of fuel consumptions is 5.7 km/L.

• 한국전자통신학회논문지
• /
• 제16권5호
• /
• pp.845-850
• /
• 2021

본 연구에서는 전기 자동차(EV : Electric Vehicle) 파워트레인의 에너지 변환 특성과 설계를 수행하였다. 그리고 EV 파워트레인의 동력원으로서 영구자석 매입형 동기 모터(IPMSM : Interior Permanent Magnet Synchronous Motor)를 대상으로 하였으며 제어를 수행하였다. IPMSM을 구동하기 위해서는 두 가지 영역인 일정한 토크와 일정한 출력(약계자) 영역이 사용되며, IPMSM을 위한 제어 시스템의 설계는 d-q 레퍼런스 프레임(벡터 제어)을 바탕으로 구성하였다. IPMSM의 두 영역에서 나타나는 모터 토크의 정적 특성을 결정하기 위해 IPMSM의 토크제어 시스템과 d축 전류 제어 시스템을 제안 및 구현하였다. 특성해석을 위해서 Matlab-Simulink 소프트웨어를 사용하였다. 최종적으로 실제 차량 사양을 기준으로 EV 차량 레벨 조건으로 변경하여 파워트레인 모델에 IPMSM을 적용하였으며 제안된 제어 시스템의 시뮬레이션 결과를 수행했고 특성을 분석하였다.

• 융복합기술연구소 논문집
• /
• 제3권1호
• /
• pp.15-18
• /
• 2013

The next generation alternative fuel of diesel, DME (Dimethyl Ether) discharges particulate matter hardly due to chemical structural as oxygen-fuel so it has the eco-friendly property. Despite these advantages, the DME has the technical difficulties to apply to the diesel engine because of a low calorific value, viscosity and compressibility effects. From this point of view, we performed experimental studies on improved reliability of DME common-rail vehicle and lubricity enhancement of DME fuel for empirical distribution of eco-friendly DME fuel. Also we analyzed solubility of lubrication enhancer according to a drop in temperature, try to secure reliability about core parts of DME vehicle by applying lubrication enhancer in the DME common-rail vehicle.

• 한국소음진동공학회논문집
• /
• 제11권4호
• /
• pp.5-12
• /
• 2001

This paper presents the simulation methodology of the interior noise of vehicle using the frequency response function based hybrid modeling of the system which consists of multi-subsystem models obtained by the test or analysis. The complex systems such as a trimmed body of high modal density and a powertrain were modeled by using experimental data, and a sub-frame of a vehicle of low modal density was modeled by finite element data. Modeling of the whole system was executed and validated in the two stages. The first stave is combining the trimmed body and the sub-frame, and the second stage is attaching the powertrain, which is a exciting source, to the combined model of the first stage. The input force to the system was modeled as an equivalent force in the virtual space, which was obtained from impedance method using the FRFs of the powertrain and the responses. The interior noise predicted by the proposed method was very close to the direct measurement, which showed feasibility of the proposed modeling procedure. Since the methodology is easily applied to both the transfer path analysis of structure-borne noise and the analysis of noise contribution of a sub-system, it is expected to be a strong tool for design change of a vehicle in the earlier stare.

• 한국자동차공학회논문집
• /
• 제15권1호
• /
• pp.99-105
• /
• 2007

It is very important to clarify the 3-D angular flow characteristics of in-cylinder bulk motion in the developing process of variable induction system. In-cylinder flow induced by variable induction system is very complex, so we can not describe the in-cylinder bulk flow characteristics using the conventional swirl or tumble coefficient. In this study, we introduced the new 3-D angular flow index, angular flow coefficient($N_B$), for in-cylinder bulk flow characteristics. And also, to confirm the index, we carried out the steady flow rig test for intake port of test engine varying valve lift on the test matrix.

• 대한기계학회논문집A
• /
• 제36권11호
• /
• pp.1371-1379
• /
• 2012

본 논문에서는 직접분사 가솔린엔진 부품에 의해서 발생하는 진동에 대한 기여도를 분석하는 방법을 제시한다. 본 연구에서는 부분기여도함수를 적용하여 부품 상호간의 관련성에 대한 진동원을 규명 하는데 사용하였다. 직접분사 가솔린 엔진 부품의 진동원을 규명하는데 부분기여도함수 방법을 사용하기 위해서는 시스템의 모델링이 필요하며 본 연구에서는 진동 발생 경로를 2 입력과 단일 출력계로 시스템을 모델링하였다. 이 모델링을 증명 하기 위해서, 직접분사가솔린 엔진의 진동원인 고압펌프, 연료레일, 인젝터, 고압센서에 3 축 가속도계 센서로 각 부품의 진동을 측정했다. 이 모델링을 바탕으로 각각의 진동원에 대한 부분기여도 함수를 구했으며, 직접분사 부품들의 각각의 진동 기여도를 계산하였다. 부분기여도 함수를 바탕으로 한 모델링을 통해 각 부품들에서 발생되는 진동 출력 기여 값을 정량적으로 도출하였다.