• Journal of the Korean Society for Nondestructive Testing
• /
• v.14 no.2
• /
• pp.122-131
• /
• 1994

Journal bearings in the rotating machineries are vulnerable to the contamination or the insufficient supply of lubricating oil, which is likely to be the cause of unexpected shutdown or malfunction of these systems. Various destructive and nondestructive testing methods had been used for the reduction of maintenance cost and the operational safety problems due to the accidents related to bearing damages. In this experimental approach, acoustic emission monitoring is employed to the detection of incipient failure caused by intervention of foreign particles most probable in the journal bearing systems. Experimental schedules for the intervention of foreign particles was composed to be more quantitative and systematic than last study in consideration of minimum oil film thickness and particle size. The experiment was conducted under such designed conditions as inserting alumina particles to the lubrication layer in the simulated journal bearing system. Several parameters such as AE rms level, waveform, AE energy distribution and other AE event parameters are used for analysis and characterization of damage source. The results showed that the history of damage was well correlated with the changes of AE rms level and the type of damage source signal can be verified using other informations such as waveform, distributions of AE parameters etc.

• The Journal of the Korea Contents Association
• /
• v.13 no.12
• /
• pp.604-613
• /
• 2013

Advanced research has often discussed that the melodrama genre reproduces typical female image more than any other genre in setting up female image. However, the advanced research is not based on quantitative methods, so it is hard to say that it has verified the conservativeness or typicality of the melodrama genre. This study applies quantitative research methods for the typicality of female image in the TV melodrama genre and intends to prove it through comparative analysis with the overall genre female image. According to the study result, the TV melodrama genre's shows less change than the overall genre female image. About their appearance, the overall genre female image indicates increase of non-femininity and activeness in their relationship with others; however, in the melodrama genre, women with typical feminine appearance and passive female image have been maintained from 1992 till 2012. In the system in which women shared men's capital in their lover or wife's status, their feminine and beautiful appearance was used as women's physical capital that enhances their possibility to be selected by men. Even in the present that women's economic power has been elevated, however, the melodrama genre still maintains typical female image distinctively. Typicality of such female image shown in the melodrama genre of which major viewers are women seems to represent contemporary women's ambivalent and contradictory desire.

• Science of Emotion and Sensibility
• /
• v.14 no.3
• /
• pp.435-444
• /
• 2011

The development of ubiquitous healthcare technology and portable electronic devices requires new energy sources for providing continuous power supply. This study particularly focuses on an energy harvesting system capable of charging energy using clothing. One of the sources for energy harvesting is heat energy, which is the difference in temperature of the body and the surrounding environment. In this study, the skin temperature distribution of the human body was empirically measured to determine the basic materials needed to develop heat energy harvesting clothing. The distribution of skin temperature in different sections of the human body was analyzed. The analysis found that the skin temperature of the upper body was higher than that of the lower body. The area close to the heart with a lot of blood flow was especially high. The skin temperature of the back side of the body, such as the back of the neck, upper back, and waist, was higher than that of the front side of the body. As for the arms, the skin temperature of the upper arms was higher than that of the lower arms, and the skin temperature of the back side of the arms was lower than that of the front and the flank side of the arms. The difference in the average skin temperature and the environment temperature was highest at the back of the neck, and thereby is considered to be the most appropriate section to integrate the heat energy harvesting function and structure. The following sections had the next highest difference in values, listed in descending order: the back of the waist, the sides of shoulders, the front chest area, the front side of the upper arms, and the front abdomen. Based on the skin temperatures of the different sections of the human body, this study outlines the basic guidelines for developing heat energy harvesting clothing.

• Journal of Astronomy and Space Sciences
• /
• v.24 no.1
• /
• pp.69-78
• /
• 2007

The international EARTHSHINE mission is to measure 1% anomaly of the Earth global albedo and total solar irradiance using Amon-Ra instrument around Lagrange point 1. We developed a new ray truing based integrated end-to-end simulation tool that overcomes the shortcomings of the existing end-to-end performance simulation techniques. We then studied the in-orbit radiometric performance of the breadboard Anon-Ra visible channel optical system. The TSI variation and the Earth albedo anomaly, reported elsewhere, were used as the key input variables in the simulation. The output flux at the instrument focal plane confirms that the integrated ray tracing based end-to-end science simulation delivers the correct level of incident power to the Amon-Ra instrument well within the required measurement error budget of better than ${\pm}0.28%$. Using the global angular distribution model (ADM), the incident flux is then used to estimate the Earth global albedo and the TSI variation, confirming the validity of the primary science cases at the L1 halo orbit. These results imply that the integrated end-to-end ray tracing technique, reported here, can serve as an effective and powerful building block of the on-line science analysis tool in support of the international EARTHSHINE mission currently being developed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.2
• /
• pp.117-124
• /
• 2018

This paper describes the localization development of an axial fan for KM-SAM multi-function radar. The multi-function radar, which is constantly affected by the external environment, is a key instrument for detecting and tracking low and medium altitude threat targets. Operating this equipment smoothly requires a fan for controlling the internal temperature and humidity. Presently, all such fans are imported. To solve these problems, localization development research was proposed. The development of localization includes analysis of requirements through review of related technical reports such as original equipment and system equipment specification, prototype design, and verification of design requirement through performance test and environmental test. The study results are described. The blower consisted of an axial fan with guide vanes and the motor was designed to generate a maximum airflow of 970 CFM and a wind pressure of 4.8 IWG. Six prototypes were manufactured for performance evaluation. In addition, for reliable data acquisition, AC power supply, fan performance tester and data acquisition equipment were designed and tested. All prototypes were verified as having design requirements equal to or better than those of imports.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 1999.05a
• /
• pp.254-260
• /
• 1999

Meteor Burst Communication can provide effective and economical means of communication where long distance VHF NLOS data transmission is needed; often ranges more than 1000 km. It has been, however, so far considered unsuitable for short distance application because of phenomenal decrease in burst durations, which leads to decreation of total duty rate of the system. This paper extensively analyzes characteristics of shot distance MB(Meteor Burst) path and shows the low duty rate may be improved by increasing burst rate through adapting antenna beam width to cover entire hot-spot region in the space and, by compensating effective burst length through cutting down man-made noises introduced by antenna. Based on the analysis, we are developed a small-opening-cavity antenna, especially designed for short distance MB path. In operation, the antenna is to be buried under ground surface so as to improve directivity and reduces noise introduction. The antenna exhibits power gain of 3 dB with 90 degree beam width and thus enables to illuminate entire hot-spot regions with the elevation angle of 8-90 degree which is the case of transmission less than 100 km. Directivity horizontal to earth surface is suppressed to minimum which enables to cut man-made noises from near-by sources down to more than 3 dB from the level reported with conventional 4 element Yagi. A series of experiments performed on 100 km MB paths have conformed that, with the antenna installed at receiving site, the burst rate and duration time have been noticed to increase by 10 and 20 percent respectively from the values obtained by conventional 4-element Yagi antenna under same testing condition.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.12
• /
• pp.511-517
• /
• 2016

Current oil-type potential transformers for trains are filled with insulating oil, which could have problems like explosions due to rising inner pressure during train operation. Therefore, mold and dry-type potential transformers are being developed to prevent explosions. One problem in manufacturing mold-type transformers is preventing void formation around the coiled core inside the mold during epoxy filling, which could cause an electrical spark. Micro voids can remain in the resin after filling, and macro voids can occur due to the structure shape. A transformer that is being developed has a cavity at the junction of the core and the coil for better performance, and when highly viscous epoxy flows inside the cavity channel, macro voids can form inside it. Therefore, in this study, the free-surface flow of the mold filling procedure was analyzed numerically by applying the VOF method. The results were used to understand the phenomena of void formation inside the cavity and to modify the process conditions to reduce voids.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.4
• /
• pp.85-92
• /
• 2018

Reductions of the electricity charge are achieved by demand management of the load. The demand management method of the load using ESS involves peak shifting, which shifts from a high demand time to low demand time. By shifting the load, the peak load can be lowered and the energy charge can be saved. Electricity charges consist of the energy charge and the basic charge per contracted capacity. The energy charge and peak load are minimized by Linear Programming (LP) and Quadratic Programming (QP), respectively. On the other hand, each optimization method has its advantages and disadvantages. First, the LP cannot separate the efficiency of the ESS. To solve these problems, the charge and discharge efficiency of the ESS was separated by Mixed Integer Linear Programming (MILP). Nevertheless, both methods have the disadvantages that they must assume the reduction ratio of peak load. Therefore, QP was used to solve this problem. The next step was to optimize the formula combination of QP and LP to minimize the electricity charge. On the other hand, these two methods have disadvantages in that the charge and discharge efficiency of the ESS cannot be separated. This paper proposes an optimization method according to the situation by analyzing quantitatively the advantages and disadvantages of each optimization method.

• Journal of Sasang Constitutional Medicine
• /
• v.16 no.1
• /
• pp.61-73
• /
• 2004

This study was prepared to investigate the correlation between Sasang constitutional groups and voice characteristics using voice analysis system(in this study, CSL). I focused on the voice characteristics in terms of harmonics, Formant frequency and Formant Bandwidth. The subjects were 71 males. I classified them into three groups, that is Soeumin group, Soyangin group and Taeumin group. The classification method of Constitution used two ways, QSCCII(Questionnarie for the Sasang Constitution Classification II) and Interview with a specialist in Sasang Constitution. So 71 people were categorized into 31 Soeumin(people), 18 Soyangin(people) and 22 Taeumin(people). Pitch is approximately similar to the fundamental frequency(F0) in voices. Shimmer in dB gives an evaluation of the period-to-period variability of the peak-to-peak amplitude within the analyzed voice sample. FFT(Fast Fourier Transform) method in CSL can display sampled voices into harmonics. H1 is the first peak and h2 is the second peak in the harmonics. The amplitude difference of h1 and h2(h1-h2) can be explained as the speaker's phonation type, And Formant frequency and bandwidth can be explained as the speaker's vocal tract. So I checked the harmonics and Formant frequency and Bandwidth as the voice parameters. First I have captured /e/ voices from all subjects using microphone. And then I analyzed /e/ voices with CSL. Power Spectrum and Formant History is the menu in the CSL which can display harmonics and Formant frequency and bandwidth. The results about the correlation between Sasang Constitutional Groups and voice parameters are as follows; 1. There is no significant amplitude difference of harmonics(h1-h2) among three groups. 2. There is the significant difference between Soeumin Group and Soyangin Group in Formant Frequency 1 and Formant Bandwidth 1(p<0.05). Any other parameters have no significance. I assume that Soyangin Group has clearer and brighter voice than Soeumin Group according to the Formant Bandwidth difference. And I think its result has coincidence with the context of "Dongyi Suse Bowon" and "Sasangimhejinam".

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.25 no.6
• /
• pp.658-665
• /
• 2019

Among the renewable energy resources, wind power is growing rapidly in terms of technological development and market share. Recently, onshore wind farm have been affected by limitations of terrestrial space and environmental problems. Consequently, installation sites have been moved to the sea, and the development of floating offshore wind farms that are installed at deep waters with more abundant wind conditions is actively underway. In the context of maritime traffic, the optimal site of offshore wind farms is required to minimize the interference between ships and wind turbines and to reduce the probability of accidents. In this study, genetic algorithm based AIS(Automatic Indentification System) data composed of genes and chromosomes has been used. The optimal site of floating offshore wind farm was selected by using 80 genes and by evaluating the fitness of genetic algorithm. Further, the final site was selected by aggregating the seasonal optimal site. During analysis, 11 optimal site were found, and it was verified that the final site selected usng the genetic algorithm was viable from the perspective of maritime traffic.