• JSTS:Journal of Semiconductor Technology and Science
• /
• 제15권4호
• /
• pp.437-444
• /
• 2015

A high output power voltage controlled oscillator (VCO) in the U-band was implemented using a 65 nm CMOS process. The proposed VCO used a transmission line to increase output voltage swing and overcome the limitations of CMOS technologies. Two varactor banks were used for fine tuning with a 5% frequency tuning range. The proposed VCO showed small variation in output voltage and operated at 51.55-54.18 GHz. The measured phase noises were -51.53 dBc/Hz, -91.84 dBc/Hz, and -101.07 dBc/Hz at offset frequencies of 10 kHz, 1 MHz, and 10 MHz, respectively, with stable output power. The chip area, including the output buffer, is $0.16{\times}0.16mm^2$ and the maximum output power was -0.11 dBm. The power consumption was 33.4 mW with a supply voltage of 1.2-V. The measured $FOM_P$ was -190.8 dBc/Hz.

• Current Photovoltaic Research
• /
• 제7권3호
• /
• pp.71-75
• /
• 2019

Solar energy is one of the renewable energy sources. It can respond to expanding energy demand. A solar cell module is designed to have a durability that can be developed over a long period of 25 years to be installed outdoors and perform like a stable power supply. We need Standard Test Condition (STC)-based power output data before and after testing to measure the power output of existing modules. The modules are shown to reduce power output by comparing data before and after outdoor experiments regardless of whether they are indoor or outdoor. It is easy to compare the power output quantities through the module simulator in the indoor. However, it takes a lot of testing time and costs to compare the power output on outdoor in the case of a high number of modules and distance from the module simulator. It can save time and costs if we can check the power output using the data in outdoor. We have used the long-term outdoor test to find the elements out that corresponds to the reductions in power output quantities. We have conducted research that matched the actual and the tests.

• 대한기계학회논문집
• /
• 제11권6호
• /
• pp.971-974
• /
• 1987

본 연구에서는 최적설계를 위한 기초로서, 고정된 두 열원사이에서 작동하는 열기관을 예로 들어 운전조건에 따른 출력과 효율의 변화를 정성적으로 설명하여 출력 과 효율의 최대값이 극대값으로 나타남을 보이고, 경제적 측면에서 이들의 의의 및 경 제적 최적운전조건과의 관계 등을 고찰하려 한다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2005년도 전력전자학술대회 논문집
• /
• pp.106-108
• /
• 2005

High accuracy and stability digital controlled power supply for magnet is developed at PLS. This power supply has three sections. The first section is digital controller including DSP&FPGA and precision ADC, the second section consists of IGBT driver and four quad IGBT switch, and the third section is LC output filter section. AC input voltage of power supply is 3-phase 21V, output current is 0 ${\sim}$ 150 A dc. Switching frequency of four quad IGBT switch is 25 kHz. The output current of power supply has very high accuracy of 100 A step resolution at full range and the stability of +/- 1.5 ppm for short term and +/- 5 ppm for long term. This paper describes characteristics of filter and output current performance improvement after LC output filter at four quad digital power supplies.

• Journal of Electrical Engineering and Technology
• /
• 제10권1호
• /
• pp.216-226
• /
• 2015

The neutral beam injection generate ultra-high temperature energy in the tokamak of nuclear fusion. The neutral beam injection make up arc power supply, filament power supply and acceleration & deceleration power supply. The arc power supply has characteristics of low voltage and high current. Arc power supply generate arc through constant output of voltage and current. So this paper proposed suitable buck converter for low voltage and high current. The proposed buck converter used parallel switch because it can be increased capacity and decrease conduction loss. When an arc generated, the neutral beam injection chamber occur high voltage. And it will break output capacitor of buck converter. Therefore the output capacitor was removed in the proposed converter. Thus the proposed converter should be designed for the characteristics of low voltage and high current. Also, the arc power supply should be guaranteed for system stability. The proposed parallel buck converter enables the system stability of the divided low output voltage and high current. The proposed converter with constant output be the most important design of the output inductor. In this paper, designed arc power supply verified operation of system and stability through simulation and prototype. After it is applied to the 288[kW] arc power supply for neutral beam injection.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제53권1호
• /
• pp.47-54
• /
• 2004

A new high voltage DC power supply is proposed. The proposed power supply is constructed with several power converters connected in series. It is easy to obtain high DC voltage for the same structure of each power converter. The output DC power of the proposed power supply can be disconnected from the load within several hundred microseconds at the instant of a load short-circuit fault. The rising time of the output DC voltage is also as small as several hundred microseconds, and there is no overshoot of the voltage because all of the output filter capacitors keep undischarged state even in load short-circuit condition. Therefore, the proposed scheme is suitable for the protection of frequent output short-circuit and fast on/off switching of output DC voltage. The proposed power supply has improved features such as simple structure, high power factor, and reduced size and volume compared with the conventional schemes. The operating principle is described and the validity of the proposed scheme is proved through simulations and experiments.

• 센서학회지
• /
• 제21권4호
• /
• pp.303-310
• /
• 2012

We carried out the power performance evaluation for 1.5 MW${\times}$2 by using anemometer installed on WTGS(Wind Turbine Generator System) in the wind farm at Shi-hwa bang-a-mu-ri. In this paper, we compared and analyzed the performance of guaranteed output and measured output of WTGS which includes output curve, output coefficient, AEP(Annual Energy Product) and availability, etc.. The power performance of WTGS was optimized in the low wind speed sections(3 m/s ~ 10 m/s) and the measured output was more produced by AEP 109 % and availability 112 % than the guaranteed output. In addition, we could also cut the high cost of testing WTGS performance by using anemometer as a substitute for weather mast.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2016년도 추계학술대회
• /
• pp.85-88
• /
• 2016

90도 하이브리드 커플러에서 두 개의 출력 단자는 일반적으로 90도 위상차의 동일 전력으로 분배된다. 90도 하이브리드 커플러의 두 개의 출력 단자는 입력 단자로부터 전기적 길이가 다르기 때문에 주파수에 따라 서로 다른 출력 기울기를 갖는다. 즉, 동일 전력으로 분배하는 90도 하이브리드 커플러는 중심 주파수에서만 동일한 전력으로 분배되고, 중심 주파수에서 멀어질수록 두 출력 단자에서의 출력 전력은 차이가 크게 발생한다. 본 논문에서는 입력단자와 가까운 거리에 있는 출력단자에 사이에 존재하는 특성임피던스 $35-{\Omega}$의 ${\lambda}/4$ 길이의 선로를 변형시켜 광대역에서 두 개의 출력 단자의 출력 특성이 동일하도록 개선시켰다. 제안된 회로는 ADS(advanced Design System)을 이용하여 살펴보면 두 개의 출력 전력의 차이가 중심주파수 대비 약 20% 대역 이상에서 0.2dB 이내의 값을 가짐을 확인하였다.

• 설비공학논문집
• /
• 제21권8호
• /
• pp.462-467
• /
• 2009

Researches and developments on BEMS are performed world-widely through sustainable management in various conditions. However, there are many obstacles to adapt the system in existing buildings because it needs highly expensive equipments, which are designed for newly built buildings, to install. Therefore, there are numerous limits exist when applying the BEMS in established buildings. The purpose of this study estimates the optimization of RF output power in WSN(Wireless Sensor Networks), which is the essential technology to develop PEMS. The results of this study is as follows ; 1) Applying WSN technique in buildings was possible. 2) As RF output power increases, the number of relay node reduced, therefore, the WSN showed more stability. 3) When estimating optimal RF output power in school, it should be considered between the number of relay node and RF output power. 4) Considering battery consumption and possibility of reception, the best suited RF output power is -20dbm in apartment house.

• 플랜트 저널
• /
• 제9권3호
• /
• pp.43-47
• /
• 2013

발전 플랜트의 발전량 최적화 및 발전효율 최적화는 에너지공학을 전공한 전문가일지라도 이해하기 힘든 개념이다. 본 연구에서는 엑서지 및 엑서지율이라는 열역학적 상태값을 적용하여 에너지 공학을 전공하지 않은 일반인일지라도 발전량 및 발전효율 최적화 개념을 쉽게 이해할 수 있는 차트가 개발되었다. 발전소의 성능을 파악할 수 있는 대표적인 물성치는 주증기의 온도 및 압력이다. 개발된 차트에서는 주증기의 온도 및 압력에 따른 최대 발전량 곡선과 최대 효율 곡선이 도시되어 있으므로, 해석하고자 하는 발전소의 온도 및 압력을 차트에 적용하여 그 발전소가 얼마만큼 최대 발전량과 최대 효율에 접근해 있는지를 쉽게 파악할 수 있다.