• Nuclear Engineering and Technology
• /
• v.53 no.2
• /
• pp.572-582
• /
• 2021

This study investigated the creep and creep crack growth (CCG) behavior of the base metal (BM), weld metal (WM), and heat affected zone (HAZ) in a Gr. 91 weldment, which was made by a shield metal arc weld process. A series of tensile, creep, and CCG tests were performed for the BM, WM, and HAZ at 550 ℃. Creep behavior of the BM, WM, and HAZ was analyzed in terms of various creep laws; Norton's power-law, Monkman-Grant relation and damage tolerance factor (λ), and their constants were determined. In addition, each CCGR law for the BM, WM, and HAZ was proposed and compared in terms of a C^*-fracture parameter. The WM and HAZ revealed faster creep rate, lower rupture ductility, and faster CCGRs than the BM, but they showed a similar behavior in the creep and CCG. The CCGRs obtained in the present study exhibited a marginal difference when compared with those of RCC-MRx of currently elevated design code in France. A creep crack path in the HAZ plane progressed towards a weak fine-grained HAZ adjacent to the BM.

• Journal of Aerospace System Engineering
• /
• v.15 no.4
• /
• pp.11-20
• /
• 2021

The estimation of hovering flight time of multicopters using the battery power propulsion system is important for the development and design of the aircraft and its operation. For a given operational weight, the maximum possible battery weight can be decided using both a conventional energy density method and a new Peukert law. In the present study, the hovering flight time is predicted using both methods. The specific data of multicopters in the published literatures were employed for the computation of the hovering flight time. The results were validated with the measured data. The effect of figure of merit of propeller, battery discharging process on the hovering flight time was evaluated, Finally, the effect of the battery cell and package connection types on the hovering time was investigated. It was found that the combination of serial battery cell connections and parallel package connection is the bast in the endurance maximization aspect. As the cell number increases in a package, the hovering flight time is increased. There exists the max. battery ratio for the given takeoff gross weight.

• The Southeast Asian review
• /
• v.23 no.1
• /
• pp.45-87
• /
• 2013

This paper aims to study Thai democratic deepening and the constitutional engineering with the analytical concepts of 'power sharing' and 'accountability' focusing on the 1997 and 2007 Constitution. With regard to power sharing, the 1997 Constitution had the characteristics of majoritarian principle including a two-party system, strengthening of prime minister and the executive's power etc. It enhanced significantly the aspects of accountability compared with the previous constitutions. The institutions such as Constitutional Court, Commission on Election, Administration Court, Commission on Human Right, Ombudsman, Commission on Anti-corruption, and the Measure for Anti-money Laundering were established by the 1997 Constitution. However, such empowered accountability system were often abused by the political power groups in the political process. The 2007 Constitution has the characteristics of consensual principle including a multiparty system, proportional representation system, weakened prime minister's power, balancing of cabinet and parliament's power, pushing ahead with decentralization. However, the consensual principle of the 2007 Constitution came, in part, from the factional interests. It is similar to the 1997 Constitution in terms of accountability system, which enhanced in law but abused often in practice. One of the critical reasons for the failure of the 1997 and 2007 constitutions to consolidate democratic system was the political game played around the so-called network for the monarchy composed by the military, the civilian bureaucracy, Constitutional Court and the privileged classes. The future of the Thai democratic deepening depends on the constitutional engineering in which the factional interests should be excluded, and the rules of power sharing and accountability which traditionally played around the network for the monarchy should be effectively institutionalized.

• Journal of KIISE:Information Networking
• /
• v.37 no.3
• /
• pp.167-174
• /
• 2010

Recently the distributed topology control algorithm for constructing the Recrystallization Topology in the unstructured peer-to-peer network was proposed. In this paper, we prove that such a hierarchical topology is a scale-free power-law network. We present a model of a construction process of the distributed protocol, and analyze it based on a mean-field approximation and the continuum theory, so that we show that the constructed Recrystallization Topology is a scale-free network. In the proposed model, all nodes are born with some initial attractiveness and the system incorporates the rewiring of some links at every time step. Some old links are removed with the anti-preferential probability, and some new links are added with preferential probability. In other words, according to the distributed algorithm, each node makes connections to the more-preferential nodes having higher hit-ratio than other nodes, while it disconnects the anti-preferential nodes having lesser hit-ratio. This gives a realistic description of the local processes forming the recrystallization topology in unstructured peer-to-peer network. We calculate analytically the degree distribution. The analytic result indicates that the constructed network is a scale-free network, of which the scaling exponent is 3.

• Journal of the Korean Institute of Gas
• /
• v.27 no.1
• /
• pp.78-85
• /
• 2023

Fixed-bed reactor Computational Fluid Dynamics (CFD) simulation of methanol steam reforming reaction was performed using the intrinsic kinetic data of the copper-impregnated hydrotalcite catalyst. The activation energy of the copper hydrotalcite catalyst obtained from the previous study results was 97.4 kJ/mol, and the pre-exponential was 5.904 × 10¹⁰. Process simulation was performed using the calculated values and showed a similar tendency to the experimental results. And the conversion rate according to the change of the reaction temperature (200 - 450 ℃) and the molar ratio of methanol and water was observed using the intrinsic kinetic data. In addition, mass and heat transfer phenomena analysis of a commercial reactor (I.D. 0.05 - 0.1m, Length 1m) was predicted through axial 2D Symmetry simulation using the power law model of the above kinetic constants.

• Transactions of Materials Processing
• /
• v.24 no.4
• /
• pp.227-233
• /
• 2015

In this paper, the effect of flow stress, friction, temperature, and velocity on finite element predictions of metal flow lines after cylindrical upsetting is presented. An actual three-stage hot forging process involving an upsetting step is utilized and experimental metal flow lines are measured to study the effect of the various process variables. It was found that temperature and velocity for reasonable values of friction have little influence on metal flow lines especially those located deep within the cylinder but that flow stress has a direct influence on the flow lines. It was shown that a pure power law material model cannot reflect the real flow stress of hot material because it underestimates the flow stress especially around the dead-metal zone for the upsetting of a cylindrical specimen. It is thus recommended that a proper lower limit of flow stress be assumed to alleviate this issue.

• Journal of Electrical Engineering and Technology
• /
• v.6 no.1
• /
• pp.59-66
• /
• 2011

This work treat the modeling and simulation of non-linear dynamic behavior of a web winding process during traction. We designate by a winding process any system applying the cycles of unwinding, transport, treatment, and winding to various flat products. This system knows several constraints, such as the thermal effects caused by the frictions, and the mechanical effects provoked by metal elongation, that generates dysfunctions due to the influence of the process conditions. Several controllers are considered, including Proportional-integral (PI) and Backstepping control. This paper presents the study of Backstepping controls strategy of the winding system. Our winding system is simulated in MATLAB SIMULINK environment, the results obtained illustrate the efficiency of the proposed control with no overshoot, and the rising time is improved with good disturbances rejections comparing with the classical control law.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.9
• /
• pp.156-164
• /
• 2001

Two-dimensional solidification analysis during rheology forming process of semi-solid aluminum alloy has been studied. Two-phase fluid flow model to investigate the velocity field and temperature distribution is proposed. The proposed mathematical model is applied to the die shape of the two types. To calculate the velocity and temperature fields during rheology forming process, the earth governing equation correspondent to the liquid and solid region are adapted. Therefore, each numerical models considering the solid and liquid region existing within the semi-solid material have been developed to predict the deflect of rheology forming gnarls. The Arbitrary Boundary Maker And Cell (ABMAC) method is employed to solve the two-phase flow model of the Navier-Stokes equation. Theoretical model on the basis of the two-phase flow model is the mixture rule of solid and liquid phases. This approach is based on the liquid and solid viscosity. The liquid viscosity is pure liquid state value, however solid viscosity is considered as a function of the shear rate, solid fraction and power law curves.

• Clean Technology
• /
• v.14 no.1
• /
• pp.47-52
• /
• 2008

Among various mass transfer models to express adsorption rates for any adsorption processes, the linear driving force (LDF) model is used most. The present investigation aims at finding whether this model may be applied to real adsorption process for separation and removal of benzene. Comparison of numerical simulation results calculated by the LDF model with experimental data allowed us to find the mass transfer coefficients that are most appropriate for a specific adsorption process. Various breakthrough curves were obtained from experiments performed at many different temperatures and pressures, which in turn produced suitable mass transfer coefficients. These dependencies of mass transfer coefficient on temperature and pressure were represented by an Arrhenius type- and a power law type empirical equation, respectively.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.10
• /
• pp.1971-1981
• /
• 2002

Two-dimensional solidification analysis during rheology forming process of semi-solid aluminum alloy has been studied. Two-phase flow model to investigate the velocity field and temperature distribution is proposed. The proposed mathematical model is applied to the die shape of the two types. To calculate the velocities and temperature fields during rheology forming process, the each governing equations correspondent to the liquid and solid region are adapted. Therefore, each numerical model considering the solid and liquid coexisting region within the semi-solid material have been developed to predict the defects of rheology forming parts. The Arbitrary Boundary Maker And Cell(ABMAC) method is employed to solve the two-Phase flow model of the Navier-Stokes equation. Theoretical model basis of the two-phase flow model is the mixture rule of solid and liquid phases. This approach is based on using the liquid and solid viscosity. The Liquid viscosity is pure liquid state value, however solid viscosity is considered as a function of the shear rate, solid fraction and power law curves.