• 한국HCI학회:학술대회논문집
• /
• 2008.02a
• /
• pp.280-285
• /
• 2008

ZigBee is Low Power and Low Data Rate Wireless Communication protocol. It apply to much Ubiquitous Sensor Network. ZigBee PAN is two type PAN. One is Beacon Enabled PAN, the other is Non Beacon Enabled PAN. To support Low Power in Non Beacon Enabled PAN, End-Device enter Active status at End-Device's wishing time and send a data. So, Router does not know End-Device sends a data time. To solving this problem, Router must always exist to Active status. In this case, Router receive a power supply always in Non Beacon Enabled PAN. But Router does not receive a power supply always, Router can not normal operation, such as Router use a battery. To solve this problem, Router will be support low power. In this paper, we will present Router's Low Power Algorithm. And we suggest 'PAN Time'. Device use 'PAN Time' for PAN synchronous. Router using Low Power Algorithm can be enter to inactive status. So Non Beacon Enabled PAN of Router support the low power mode Therefore Router does not receive a power supply always, Router can normal operation.

• Journal of Internet Computing and Services
• /
• v.9 no.2
• /
• pp.43-50
• /
• 2008

In IEEE 802.11b wireless LAN, stations keep synchronization by receiving beacons being periodically sent by the AP (access point) when they run in low power mode. Beacon transmission is delayed if wireless channel is busy at a scheduled TBTT (target beacon transmission time), and stations must be awake until they receive the delayed beacon. In this paper, we propose a scheme that stations get their transmission delayed if they have little time for successful data transmission by the next TBTT. Beacon transmission without delay is guaranteed at every TBTT with this method so that the awake time of low power stations to receive beacon can be reduced. The proposed method is simulated and its characteristics ore described with the analysis of the results. The measured results in terms of beacon delay show some enhancement in energy consumption.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.4A
• /
• pp.365-372
• /
• 2007

In IEEE 802.11b wireless network, stations synchronize themselves to the beacons periodically sent by the access point(AP) when they are running in low power mode. In case of missing beacon due to noise or traffic from neighboring wireless network stations must be awake until they get the next beacon, which causes energy consumption in stations. In this paper, we propose a scheme searching next beacon consuming little energy. The problems of missing beacon in low power mode of IEEE 802.11b wireless interface are described and a new method to reduce energy consumption is proposed. The proposed method is simulated with the network simulator, ns2, and compared with the low power mode of the IEEE 802.11b. The result measured in terms of station's wakeup time shows some enhancement in energy consumption when some errors occur in receiving frames.

• Journal of Information Processing Systems
• /
• v.9 no.1
• /
• pp.41-52
• /
• 2013

One of the obstacles preventing the Zigbee protocol from being widely used is the excessive power consumption of Zigbee devices in low bandwidth and low power requirement applications. This paper proposes a protocol that resolves the power efficiency problem. The proposed protocol reduces the power consumption of Zigbee devices in beacon-enabled networks without increasing the time taken by Zigbee peripherals to communicate with their coordinator. The proposed protocol utilizes a beacon control mechanism called a "sleep pattern," which is updated based on the previous event statistics. It determines exactly when Zigbee peripherals wake up or sleep. A simulation of the proposed protocol using realistic parameters and an experiment using commercial products yielded similar results, demonstrating that the protocol may be a solution to reduce the power consumption of Zigbee devices.

• Composites Research
• /
• v.28 no.5
• /
• pp.322-326
• /
• 2015

We developed the high-power LED beacon and investigated the applicability of composite materials for the light-weight design of LED beacon. By means of the application of composite materials, the vertical deformation could be reduced by 17% and the total weight of LED beacon 8.9 kg comparable to 20% light-weighting against aluminum beacon. In thermal radiation test, the maximum temperature of LED package was measured to $63.5^{\circ}C$ under ambient temperature ($20^{\circ}C$), which is acceptable considering both performance and lifespan of LED packages. In this study, the applicability of composite materials was demonstrated for light-weight design of high-power LED beacon.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.10
• /
• pp.909-916
• /
• 2016

The beacon receiver is an equipment which detects and measures the signal strength of transmitting satellite beacon signal. Beacon signals transmitted by satellites are low power continuous wave(CW) signals without any modulation intended for antenna steering to satellite direction and power control purposes on the earth. The beacon signal detection method using a very narrow band analog filter and RSSI(Received Signal Strength Intensity) has been typically used. However, it requires the implementation to track the frequency at the beacon receiver, thus a beacon frequency variation of the satellite due to temperature changes and long-term operation. Therefore, in this paper, the beacon signal detection receiver is designed by using a very narrow band digital filter array for a faster acquisition and SNR(Signal to Noise Ratio) method detection. For this purpose, by calculating the satellite link budget with the rain attenuation between satellite and ground station, and then extracting the received $C/N_o$ of the beacon signal, this work derives the bandwidth and the array number of the configured digital filter that gives the required C/N.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.16 no.1
• /
• pp.55-60
• /
• 2016

In the traditional wireless LAN model, scan procedure to search a new AP starts when the predefined number of Rx failure of beacon frames are occurred. In this case, lots of data packet loss occur during MN's handover because loss of the relatively longer data packet starts before the small-sized beacon loss. Newly developed scanning mechanism in this paper has the beacon counter that increases when the Rx power level of beacon frame is less than the threshold and the previous rx power level. New scan procedure starts when the counter exceeds the predefined number. Beacon Rx power threshold is verified and performance of the new WLAN model is evaluated under UDP and TCP traffic environment.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.12A
• /
• pp.1303-1310
• /
• 2007

In IEEE 802.11b wireless network, stations synchronize themselves to the beacons periodically sent by the access point (AP) when they are running in low power mode. Stations stay awake for enough time to receive beacon because it is delayed in AP if the wireless channel has been being used by other traffic at each scheduled instant. In this paper, we propose a method that measures the delay of received beacons and calculates wake-up interval of station to receive the next one. Beacon transmission delay at the AP is analyzed. The proposed method is simulated and its characteristics are described in the analysis. The result measured in terms of station's wake-up interval shows some enhancement in energy consumption.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.265-268
• /
• 2005

본 논문에서 제안하는 방안은 Cricket 방식을 사용하는 위치 인식 시스템에서 전력 소모를 억제하는 방안이다. 복수의 전송 모듈인 Beacon 과 유저당 한 개씩 갖게 되는 수신모듈 Listener 로 구성되는 기본적인 Cricket 구조에서 전송 모듈인 Beacon 은 일반적으로 랜덤 방식으로 송신을 행하게 된다. 이럴 경우 사용자가 없는 구역의 Beacon 이 초음파를 계속 발생함으로써 불필요한 전력 낭비가 생긴다. 이를 막기 위해 사용자가 있는 구역의 Beacon 들에게 우선순위를 부여하여 이 Beacon 들이 우선적으로 전송을 행하게 하는 방안을 고안한다. 이 방안은 시스템의 규모가 클수록 그 효율을 발휘한다. 유저가 있는 영역의 시스템만 가동되므로 불필요한 Beacon 전력 낭비를 줄일 수 있기 때문이다. 본 논문에서는 기본적인 Cricket 구조의 설명에 이어, 제안하는 방안에 대해 논하고 마지막으로 시뮬레이션을 통한 성능 분석을 행하였다.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.42 no.1
• /
• pp.149-152
• /
• 2017

This paper investigated the method for the output of power management IC (PMIC) for BLE beacon with energy harvesting device to be maintained constantly. The capacitor was used to store the energy supplied from energy harvesting device such as solar module and the capacitance was estimated to the optimum value according to the interval for the BLE beacon to send advertising signal.