• 한국정밀공학회지
• /
• 제16권6호
• /
• pp.36-44
• /
• 1999

The rapid Tooling technique is classified into two methods: one to directly utilize the model which was made by rapid prototyping technologies for dies, and the other to make a transferred type using the model as a master model and create dies and molds using it. In this study, the Al powder filled resin was made several mixed ratios and meshes sizes, and applied to slurry casting. And, variation of mechanical characteristics such as the shrinkage rate, the tensile strength, the elongation, the hardness, and surface roughness, are measured to compare. Consequently, as higher is the powder mixed ration and as smaller is the grain size of the power, the mechanical characteristics of the final mold are improved. Finally, the metal short fiber which can be fabricated easily and cheaply, if the self-excited vibration of an elastic tool, was also applied to slurry casting. It has been found tat the hardness gets higher, while the shrinkage rate lower, if mixed with short fiber.

• Journal of the Korean Wood Science and Technology
• /
• 제22권1호
• /
• pp.44-53
• /
• 1994

This research was carried out to investigate the effect of paper sludge addition on formaldehyde emission, and physical and mechanical properties of UF-particleboard. In order to investigate the effect of paper sludge addition to resin, particleboards were bonded with urea-formaldehyde resins containing 5, 10, 15% paper sludge powders of three types(A Type: -200 mesh, B Type: -100~+200 mesh. C Type: -50~+100 mesh), based on weight of resin solid. Also the effect of paper sludge addition to furnish was studied from particleboards fabricated with ratios of sludge to particle of 5:95, 10:90, 15:85 based on oven-dry weight. Tests were conducted on the manufactured particleboards to determine formaldehyde emission, bending properties, internal bond strength and thickness swelling. The obtained results were summarized as follows: The addition of paper sludge powder to resin yielded a higher pH of cured resin. Formaldehyde emission decreased with the increase of paper sludge powder addition to resin and paper sludge composition ratio to furnish. Particleboard bonded with urea-formaldehyde resin containing paper sludge powder and particleboard mixed with paper sludge have similar bending properties(MOR, MOE) and thickness swelling compared with control particleboard. Internal bond strength of particleboards treated with paper sludge were lower than that of control particleboard. The use of paper sludge as scavenger was achieved reduction of formaldehyde emission without depression of physical and mechanical properties of particleboard. Also the use of paper sludge was able to concluded that there is possibility of partial substitution of wood particle materials.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.301-302
• /
• 2006

Machinability and machining mechanism were examined in the case where resin impregnation treatment was conducted to the Mo-Co hardening particle dispersed iron-based sintered alloy. As a result, the force required for machining decreased significantly compared with the case where resin impregnation treatment was not conducted. This effect is considered to be attributable to the embrittlement of cutting chips produced by the minimization of the cut material deformation.

• Journal of the Korean Wood Science and Technology
• /
• 제15권4호
• /
• pp.64-68
• /
• 1987

To develope the utilities of the chestnut bur, which is wasted after harvesting chestnut in farmhouses, the feasibilities of adhesion(urea resin) extenders of the powder for plywood were examined. These experiments were implemented on experimental scale at Forestry Research Institute(Seoul) and on a plywood mill scale at Eugon Industrial Co LTD(Inchon) for more reliable data. In this paper, it was proved that the chestnut bur powder caused to rise the glue viscosity but the chaff powder to down reversely. The most effective mixing ratio were wheat flour 5kg, chaff powder: 5kg and chestnut bur powder. 5kg per 100kg of urea resin. At this condition, the viscosity were most appropriate (1,320 2,230 cps) for glue spreading operations, and the dry shear strengthes were most adequate(10.7-13.2kg/$cm^2$), wood failure ratio 82-88%). The chestnut bur powder, can be utilized for plywood adhesion extenders without any change of present process lines in plywwod mills.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 1993년도 추계학술강연 및 발표대회강연 및 발표논문 초록집
• /
• pp.58-58
• /
• 1993

• 한국응용과학기술학회지
• /
• 제30권3호
• /
• pp.472-479
• /
• 2013

The conductive polymer composites recently became increasingly to many fields of industry due to their electrical properties. To understand these properties of composites, electrical properties were measured and were studied relatively. Electrical conductivity measurements showed percolation phenomena. Percolation theories are frequently applied to describe the insulator-to-conductor transitions in composites made of a conductive filler and an insulating matrix. It has been showed both experimentally and theoretically that the percolation threshold strongly depends on the aspect ratio of filler particles. The critical concentration of percolation formed is defined as the percolation threshold. This paper was to study epoxy resin filled with copper. The experiment was made with vehicle such as epoxy resin replenished with copper powder and the study about their practical use was performed in order to apply to electric and electronic industry as well as general field. The volume specific resistance of epoxy resin composites was 3.065~13.325 in using copper powder. The weight loss of conductive composites happened from $350^{\circ}C{\sim}470^{\circ}C$.

• Journal of the Korean Wood Science and Technology
• /
• 제24권2호
• /
• pp.15-19
• /
• 1996

To utilize the waste materials and develope wood adhesive from isolated bloods of slaughtered cow and pig and also to prevent water pollution, simple and rapid method of isolation and purification of plasma proteins from pig bloods with trichloroacetic acid(TCA) treatment was developed. Adding of TCA-precipitated blood powder to the phenol formaldehyde resin(PF) improved dry and wet strength of plywood and resulted in fast hot pressing times.

• Journal of the Korean Wood Science and Technology
• /
• 제43권4호
• /
• pp.528-537
• /
• 2015

폐기물의 재활용을 도모하기 위해 음식점이나 정육점에서 폐기되는 뼈(골분)를 합판용 접착제의 충전제로서 이용 가능성을 검토하였다. 현재 업계에서 합판의 제조에 사용되고 있는 3종의 접착제(UMF, UF 및 PF수지)에 대해 3종의 골분(소골분, 돼지골분 및 조개골분)을 첨가하여 제조한 라티에타파인 합판의 접착성능을 기존의 소맥분과 비교하였다. 3수지에서 모두 소맥분을 전부 소골분, 돼지골분 및 조개골분으로 각각 대체한 합판의 접착성능은 상태나 습윤 강도 및 목파율 모두 소맥분 첨가 합판보다 낮았다. 따라서 소맥분을 전혀 첨가하지 않고 골분으로 모두 대체하는 것은 곤란하였다. 그러나, 소맥분의 절반을 소골분과 돼지골분으로 각각 대체하여 제조한 합판의 성능은 소맥분을 사용한 합판과 거의 동등하거나 오히려 우수한 내수성능을 발휘하여 소맥분과 병용해서 사용하면 충분히 이용이 가능할 것으로 생각된다. 소맥분과 병용한 경우, 3종의 골분 중에는 조개골분을 첨가하여 제조한 합판 보다는 소골분과 돼지골분을 첨가한 합판의 성능이 우수하였으며, 소골분과 돼지골분 간에는 큰 차이가 없었다.

• Carbon letters
• /
• 제8권4호
• /
• pp.326-334
• /
• 2007

In this study, graphite composites were fabricated by warm press molding method to realize commercialization of PEM fuel cells. Graphite composites have been considered as alternative economic materials for bipolar plate of PEM fuel cells. Graphite powder that enables to provide electrical conductivity was selected as the main substance. The graphite powder was mixed with phenolic resin and the mixture was pressed using a warm press method. First of all, the graphite powder was pulverized with a ball mill for the dense packing of composite. As the ball milling time increases, the average size of particles decreases and the size distribution becomes narrow. This allows for improvement of the uniformity of graphite composite. However, the surface electrical resistivity of graphite composite increases as the ball milling time increases. It is due to that graphite particles with amorphous phase are generated on the surface due to the friction and collision of particles during pulverizing. We found that the contact electrical resistivity of graphite particles increases as the particle size decreases. The contact electrical resistivity of graphite powders was reduced due to high molding pressure by warm press molding. This leads to improvement of the mechanical properties of graphite composite. Hydrogen gas impermeability was measured with the graphite composite, showing a possibility of the application for bipolar plate in fuel cell. And, I-V curves of the graphite composite bipolar plate exhibit a similar performance to the graphite bipolar plate.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2005년도 춘계학술발표대회 논문집
• /
• pp.257-260
• /
• 2005

Graphite reinforced conductive polymer composites were fabricated by the compression molding technique. Graphite powder was mixed with an phenol resin to impart electrical property in composites. The ratio and particle size of graphite powder were varied to investigate electrical conductivity of cured composites. In this study, graphite reinforced conductive polymer composites with high filler loadings(>66wt.%) were manufactured to accomplish high electrical conductivity. With increasing the loading ratio of graphite powder, the electrical conductivity and flexural strength increased. However. above 80wt.% filler loadings, flexural strength decreased due to lack of resin. Regardless of graphite particle size, electrical conductivity wasn’t varied. On the other hand, with decreasing particle size, flexural strength increased due to high specific surface area.