• 한국결정성장학회지
• /
• 제32권1호
• /
• pp.25-32
• /
• 2022

인베스트먼트 주조는 정밀기기, 의료분야, 액세서리 등의 제조에 일반적으로 사용되는 생산방식으로 장비의 현대화와 고품질의 재료를 통해 발전을 거듭해 왔으며 그 활용 범위가 확대되고 있다. 본 연구의 목적은 인베스트먼트 주조 공정의 핵심 요소인 금형 온도의 구조적 개선 및 표준화를 도출하여 불량률을 최소화하여 경제성과 생산성을 향상시키는 것이다. 연구의 범위는 소형탕도의 구조와 원리를 이해하기에 적합한 Jewelry 제조 주조 공정에 국한되어 있으며 연구 재료로 soft Wax, 석고 분말 및 14 K Gold를 사용하여 실험적 연구를 수행했다. 그 결과 Alloy 14 k의 주물 패턴에 가장 적합한 주물 표준 온도는 980℃ 플라스크 온도 550℃에서 가장 낮은 난류로 좋은 제품을 생산할 수 있었다. 본 연구의 향후 과제로 소형탕도의 구조 및 표준온도를 데이터를 분석하고, 현장의 생산 불량을 감소시키고 우수한 인베스트먼트 주조 공법의 경쟁력 확보를 위한 데이터를 제공하기 위한 세부 연구가 필요하다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집 Vol.14 No.1
• /
• pp.341-345
• /
• 2001

In this study, nano-sized powders of $Si0_2-0^{\sim}15mol%B_2O_3$ composition were prepared by sol-gel processing method using TEOS(Tetra ethyl ortho silicate) and $H_3BO_3$ solution. The powders were tape-cast on High silicate glass sheet(HSG) substrate and sintered to form a layer of undercladding for the planar light wave module, During the sol-gel processing, $H_2O/Si$ mole ratio were varied to modify the size of the powders in a range from 600 to 75nm. The dispersion of the powder was modified by changing the pH of the slurry. Sintering temperature of the tape was observed to decrease with the size of the powder and the $B_2O_3$ content in the powder. When the silica powders of 75-125nm in diameter containing 15mol% $B_2O_3$ were used, 98 TD% was obtained at $1250^{\circ}C$, which is approximately $300^{\circ}C$ reduction in sintering temperature compared with micrometer-sized powders.

• 한국주조공학회지
• /
• 제19권1호
• /
• pp.54-65
• /
• 1999

The present work is an attempt to evaluate the relationship between dendrite arm spacing and average cooling rate in gasatomized $Al_{87.3}misch$ $metal_{8.3}Ni_{4.4}$ powder by means of the following methods. One is calculation of heat transfer coefficient and average cooling rate, which are derived from estimated particle velocity during gas-atomization. The other is measurement of secondary dendrite arm spacing, which are observed on the particle surface. Then, we make experimental equation for this relationship in case of permanent mold casting and compare it with similar equation in case of rapidly solidified powder. Both average cooling rates and solidification rates are considered to represent the variance of dendrite arm spacings in two types soidification route. Even though there is a considerable difference in each average cooling rate, the dendrite arm spacing values are similar in two cases; particle diameter, $100\;{\mu}m$, and casting width, 2.05 mm. It is because that each solidification route has similar solidification rate.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집
• /
• pp.341-345
• /
• 2001

In this study, nano-sized powders of SiO$_2$-0∼15mo1%B$_2$O$_3$ composition were prepared by sol-gel processing method using TEOS(Tetra ethyl ortho silicate) and H$_3$BO$_3$ solution. The powders were tape-cast on High silicate glass sheet(HSG) substrate and sintered to form a layer of undercladding for the planar light wave module. During the sol-gel processing, H$_2$O/Si mole ratio were varied to modify the size of the powders in a range from 600 to 75nm. The dispersion of the powder was modified by changing the pH of the slurry. Sintering temperature of the tape was observed to decrease with the size of the powder and the B$_2$O$_3$ content in the powder. When the silica powders of 75∼125nm in diameter containing 15mo1% B$_2$O$_3$ were used, 98 TD% was obtained at 1250$^{\circ}C$, which is approximately 300$^{\circ}C$ reduction in sintering temperature compared with micrometer-sized powders.

• 한국분말재료학회지
• /
• 제30권1호
• /
• pp.7-12
• /
• 2023

Metal-additive manufacturing techniques, such as selective laser sintering (SLS), are increasingly utilized for new biomaterials, such as cobalt-chrome (Co-Cr). In this study, Co-Cr gas-atomized powders are used as charge materials for the SLS process. The aim is to understand the consolidation of Co-Cr alloy powder and characterization of samples sintered using SLS under various conditions. The results clearly suggest that besides the matrix phase, the second phase, which is attributed to pores and oxidation particles, is observed in the sintered specimens. The as-built samples exhibit completely different microstructural features compared with the casting or wrought products reported in the literature. The microstructure reveals melt pools, which represent the characteristics of the scanning direction, in particular, or of the SLS conditions, in general. It also exposes extremely fine grain sizes inside the melt pools, resulting in an enhancement in the hardness of the as-built products. Thus, the hardness values of the samples prepared by SLS under all parameter conditions used in this study are evidently higher than those of the casting products.

• 한국인터넷방송통신학회논문지
• /
• 제19권5호
• /
• pp.245-250
• /
• 2019

현대 주조산업에서는 적층제조기술과 같은 신기술을 도입하면서 과거에는 불가능했던 일들의 실현가능성을 보여주고 있다. 이미 해외에서는 적층제조기술을 활용한 중자 생산 및 적용 사례가 심심치 않게 보도되고 있으며, 정부지원 하에 고유 기술들을 개발하고 시장을 확장해 나가고 있다. 반면 국내에서는 고유장비 기술은커녕 적층제조기술의 활용조차 전무한 실정이다. 이러한 상황에서 적층제조기술의 도입과 국산화는 반드시 필요하다. 본 논문의 각 장에서는 여러가지 적층제조기술 중 접착제 분사 기술에 관련된 적층제조장비의 개발 과정에서부터 개발 장비를 활용한 산업용 중자 생산의 내용을 다루고 있으며, 실제 주조 산업의 적용 가능성에 대해서 언급하고 있다.

• 한국분말재료학회지
• /
• 제19권4호
• /
• pp.304-309
• /
• 2012

The purpose of our study was to develop the fabrication method of porous diatomite ceramics with a porosity gradient by centrifugal molding. The processing variables of centrifugal molding were derived from Stoke's law of sedimentation, which were the radius of the particles, the acceleration due to centrifugal molding and the dynamic viscosity of the slurry. And these could be controlled by ball-milling conditions, centrifugal conditions, and the addition of methyl cellulose, respectively. The effects of processing conditions on the gradient pore structure of diatomite were investigated by particle size analysis, scanning electron microscope, and mercury porosimeter.

• 대한치과기공학회지
• /
• 제35권1호
• /
• pp.57-64
• /
• 2013

Purpose: Waste parts of zirconia blocks and powders were remained after CAD/CAM process. In order to make these residual zirconia fit for practical use, zirconia single cores were produced by drain casting process. Methods: Remained zirconia blocks were reduced to powders with zirconia mortar, and screened with 180 mesh sieve. Zirconia slip was prepared from waste parts of zirconia by ball milling. Plaster molds for forming cores by slip casting were also prepared. Formed cores were removed from mold after partial drying. Dried cores were biscuit fired at $1,100^{\circ}C$ for 1hour. Biscuit fired cores were treated with tools to control the fitness and thickness. Finished cores were $2^{nd}$ fired at $1,500^{\circ}C$ for 1hour. Microstructure of cross section of core was observed by SEM. Results: When mill pot was filled with 100g of zirconia and alumina mixed powder, 300g of zirconia ball, and 180g of distilled water, the optimum slip for drain casting was obtained. Gypsum plaster for ceramic forming was more suitable then yellow stone plaster for casting process. SEM photograph showed the microstructure of fully dense with uniform grain size of zirconia and well dispersed alumina grains into the zirconia matrix. Conclusion: Zirconia single cores were produced by drain casting process. Drain casting is useful process to make these residual zirconia fit for practical use. Further study will be focused on the preparation of the bridge type cores by casting.

• 한국결정성장학회지
• /
• 제12권3호
• /
• pp.120-125
• /
• 2002

Si-wafers for solar cells were cast in a size of $50{\times}46{\times}0.5{\textrm}{mm}^3$ by vacuum casting method. The graphite mold coated by BN powder, which was to prevent the reaction of carbon with the molten silicon, was used. Without coating, the wetting and reaction of Si melt to graphite mold was very severe. In the case of BN coating, SiC was formed in the shape of tiny islands at the surface of Si wafer by the reaction between Si-melt and carbon of the graphite mold on the high temperature. The grain size was about 1 mm. The efficiency of Si solar cell was lower than that of Si solar cell fabricated on commercial single and poly crystalline Si wafer. The reason of low efficiency was discussed.

• 한국주조공학회지
• /
• 제20권3호
• /
• pp.188-196
• /
• 2000

A vacuum casting was proposed as a new fabrication method of Si wafer for solar cell substrate. It was tried to fabricate a Si plate with good properties and to reduce the production cost by direct vacuum casting. By $5{\sim}10$ cmHg of pressure difference Si plate with $50{\times}46{\times}1.5\;mm^3$ was fabricated. For the preventing of the reaction between graphite mold and Si melt, BN powder coating or BN insert were used. The Si wafer was poly crystalline with 100 ${\mu}m{\sim}1$ mm order of grain size. And there were some twins and dislocations in the grains.