• 한국염색가공학회지
• /
• 제6권2호
• /
• pp.1-9
• /
• 1994

In order to study the effect of mordanting on silk fabrics treated with tannin, those fabrics were treated with Al, Cu, Cr, Fe, Sn by pre and post mordanting. It was studied about color change, weighting effect, dgree of photodegradation by pre and post mordanting. The results are as fallows ; 1. On the addition of mordants into mimosa and tannic acid solution, &{\lambda}_{max}& of the former was slightly blue-shifted, on the other hand, &{\lambda}_{max}& of the latter was obviously Red-shifted. 2. In case of Cu, Cr, Pre mordanting, weighting effect were appeared. Weighting effect of silk fabrics treated with Tannic acid increased higher than mimosa by mordanting. 3. In color change, Silk fabrics treated with Mimosa and Tannic acid generally changed to red direction and fabrics treated with tannic acid changed to yellow direction by pre and post mordanting. 4. In the photodegradation, the degree of photodegradation on mordanted fabrics increased. Its degree was slack in Cu, Cr, Post mordanting. On the other hand, Al, Fe, Sn were greate. Silk fabrics treated with Mimosa and Tannic acid got inhibiting effect on photodegradation.

• 대한암한의학회지
• /
• 제27권1호
• /
• pp.37-48
• /
• 2022

Objective: Insomnia is a very common symptom and has a great effect on the quality of life in cancer patients. This study was conducted to identify the effects of the aroma therapy on insomnia in cancer patients. Methods: The study was performed with one group in before-after test design. The subjects were 15 cancer patients with insomnia selected by convenience sampling in Daegu. The aroma therapy consists of 10-minute sessions twice a week over 6 weeks. The PSQI (Pittsburgh Sleep Quality Index), ISI (Insomnia Severity Index) were measured at baseline and at 3 and 6 weeks, after 6 weeks after finishing treatment. STAI (State-Trait Anxiety Inventory), FACT-G (Functional Assessment Cancer Therapy-General), HRV (Heart Rate Variability) were measured at baseline, post-treatment and after 6 weeks after finishing treatments. Results: Fifteen patients (mean age 50.93 ± 7.29 years), with breast, ovarian or gastric cancer, participated this study. At post-treatment, PSQI (from 14.18 ± 2.64 to 6.18 ± 3.03), ISI (from 19.00 ± 3.19 to 8.18 ± 5.14), FACT-G (from 55.65 ± 11.20 to 66.91 ± 12.33), and STAI (from 40.36 ± 8.10 to 34.73 ± 9.81, from 45.64 ± 6.07 to 39.73 ± 9.37) scores improved significantly over baseline(p<0.001). Conclusion: Aroma therapy improved insomnia, anxiety and quality of life on cancer patients.

• Asian-Australasian Journal of Animal Sciences
• /
• 제28권10호
• /
• pp.1488-1495
• /
• 2015

This study was conducted to investigate the effects of post-harvest storage duration and wheat variety on the digestibility and energy content of new season wheat fed to finishing pigs. Two wheat varieties (Shi and Zhong) were harvested in 2013 and stored in the warehouse of the Fengning Pig Experimental Base at China Agricultural University for 3, 6, 9, or 12 mo. For each storage period, 12 barrows were placed in metabolism crates and allotted to diets containing 1 of the 2 wheat varieties in a randomized complete block design. The experimental diets contained 97.34% wheat and 2.66% of a vitamin and trace mineral premix. With an extension of storage duration from 3 mo to 12 mo, the gross energy (GE) and crude protein (CP) of the wheat decreased by 2.0% and 12.01%, respectively, while the concentration of neutral detergent fiber (NDF), acid detergent fiber (ADF) and starch content increased by 30.26%, 19.08%, and 2.46%, respectively. Total non-starch polysaccharide, total arabinose, total xylose and total mannose contents decreased by 46.27%, 45.80%, 41.71%, and 75.66%, respectively. However, there were no significant differences in the chemical composition between the two wheat varieties with the exception of ADF which was approximately 13.37% lower in Shi. With an extension of storage duration from 3 mo to 12 mo, the digestible energy (DE), metabolizable energy (ME) content and the apparent total tract digestibility of GE, CP, dry matter, organic matter, ether extract, ADF and metabolizability of energy in wheat decreased linearly (p<0.01) by 5.74%, 7.60%, 3.75%, 3.88%, 3.50%, 2.47%, 26.22%, 27.62%, and 3.94%, respectively. But the digestibility of NDF changed quadratically (p<0.01). There was an interaction between wheat variety and storage time for CP digestibility (p<0.05), such that the CP digestibility of variety Zhong was stable during 9 mo of storage, while the CP digestibility of variety Shi decreased (p<0.05). In conclusion, the GE, DE, and ME of wheat was stable during the first 3 to 6 mo of post-harvest storage, and decreased during the following 6 to 12 mo of storage under the conditions of this study.

• 한국염색가공학회지
• /
• 제13권5호
• /
• pp.32-32
• /
• 2001

Amur cork tree contains yellow natural basic dye largely used for dyeing on silk. Dyeabilities and fastnesses of the colorant on silk fabrics were investigated , According to dye concentration, pH, temperature, time of pre- and post- treatment of mordant, K/S values and fastnesses of the silk fabrics were examined. As a results, K/S values of dyed silk fabrics were increased by pre- and post-treatment with chinese gallotannin. The optimum condition of chinese gallotannin pre-treatment was 0.15% concentration, pH 4, 70℃, and 45min, and that of post-treatment was 0.05% concentration,60℃, and 30min. The wash fastness and the light fastness were enhanced to 4 grades and 2∼3 grades.

• 한국염색가공학회지
• /
• 제13권5호
• /
• pp.320-328
• /
• 2001

Amur cork tree contains yellow natural basic dye largely used for dyeing on silk. Dyeabilities and fastnesses of the colorant on silk fabrics were investigated , According to dye concentration, pH, temperature, time of pre- and post- treatment of mordant, K/S values and fastnesses of the silk fabrics were examined. As a results, K/S values of dyed silk fabrics were increased by pre- and post-treatment with chinese gallotannin. The optimum rendition of chinese gallotannin pre-treatment was 0.15% concentration, pH 4, $70^\circ{C}$, and 45min, and that of post-treatment was 0.05% concentration,$60^\circ{C}$, and 30min. The wash fastness and the light fastness were enhanced to 4 grades and 2~3 grades.

• 대한치과교정학회지
• /
• 제19권2호
• /
• pp.109-120
• /
• 1989

We tend to consider only static occlusion such as molar relationship, canine key, and interdigitation at finishing stage. Of course, this static occlusion is important for post-orthodontic stability. But we should remember that mandible is always on the move during its various functions. If no pressure or too much pressure is put on during its functions, untoward tooth movement could occur. And tooth mobility, periodontitis, wear facet, bruxism, and far worse temporomandibular disorder could occur. After many studies have been done on what is a desirable occlusal scheme to strengthen post-orthodontic stability, today, "mutually protective occlusion" is recommended. If an orthodontist does not have understanding about this occlusal scheme during orthodontic treatment, the following conditions will be resulted after orthodontic treatment. I. Centric discrepancy 1. centric prematurity 2. sunday bite 3. molar fulcrum II. Eccentric discrepancy 1. posterior interference 2. anterior interference If we have deep understanding about these discrepancies that can happen after orthodontic treatment and their causes, corrections, and especially preventions against them, post-orthodontic stability could be strengthened and further temporomandibular disorder could be prevented.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.18-21
• /
• 2003

Fused Deposition Modeling (FDM) parts are made by piling up thin layers that cause the stair stepping effect at the surface of FDM parts. This effect brings about poor surface roughness of the part and requires additional post machining such as manual finishing that is detrimental to the part geometry and time consuming. Determining optimal build orientation for FDM parts can be one solution to minimize the post machining. However, by using the CAD model, calculating the optimal build orientation is impractical due to heavy computing process. In order to calculate the optimal build orientation with high speed. the surface roughness model based on measured data and interpolation is newly developed in this research. Also. the genetic algorithm (GA) is applied for acquiring reliable solution. Finally, It is verified from the test that the presented approach is very efficient for reducing the additional post machining process fer FDM parts.

• Asian-Australasian Journal of Animal Sciences
• /
• 제23권7호
• /
• pp.907-915
• /
• 2010

Three hundred and seventy-three steers (approximately 7 mo of age and $247{\pm}19.4\;kg$) were utilized to determine the effects of trace mineral (TM) source and growth implants on trace mineral status. Steers were blocked by ranch, post-weaning treatment within ranch, stratified by initial body weight, and randomly assigned to one of 36 pens (9-12 head/pen). Treatment consisted of: I) control (no supplemental Cu, Zn, Mn, and Co), ii) inorganic trace minerals, and iii) organic trace minerals. Six pens of steers per treatment received a growth implant at the beginning of the experiment and were re-implanted during the finishing phase. The remaining steers received no growth implants. Steers were fed a corn silage-based growing diet for 56 d then were gradually switched to a high concentrate finishing diet. Treatments during the finishing phase consisted of: i) control (no supplemental Zn); ii) inorganic Zn (30 mg of Zn/kg DM from $ZnSO_4$); and iii) organic Zn (iso-amounts of organic Zn). By the end of the growing and finishing phases, implanted steers had greater (p<0.01) plasma Cu concentrations than non-implanted steers. During the growing phase, liver Cu concentrations (p<0.01) and plasma Zn concentrations (p<0.02) were greater in steers supplemented with TM compared to control steers. Steers supplemented with inorganic minerals had greater liver Cu concentrations than steers supplemented with organic minerals at the beginning (p<0.01) and end (p = 0.02) of the growing phase. During both the growing (p = 0.02) and finishing phases (p = 0.05), nonimplanted control steers had greater plasma Cu concentrations than non-implanted steers supplemented with TM, whereas, implanted control steers had similar plasma Cu concentrations than implanted steers supplemented with TM. Non-implanted steers that received inorganic TM had lower plasma Cu concentrations (p = 0.03) during the growing phase and ceruloplasmin activity (p<0.04) during the finishing phase than non-implanted steers that received organic TM, whereas, implanted steers supplemented with either organic or inorganic TM had similar plasma Cu concentrations.

• 한국음향학회지
• /
• 제42권6호
• /
• pp.594-602
• /
• 2023

현재까지 바닥충격음은 중량 바닥충격음 연구가 주를 이루었다. 경량 바닥충격음의 경우 뜬 바닥구조만으로 충분히 차단성능을 확보할 수 있었기 때문이었다. 뜬 바닥구조에서 중량 바닥충격음의 경우 바닥완충재의 동탄성 측정을 통해 저감성능을 어느 정도 예측할 수 있다. 하지만 최근 사후 확인 제도의 도입으로 인해 다양한 바닥구조가 개발되고 있다. 특히, 완충재가 사용되지 않는 바닥구조에서는 경량 바닥충격음에 지대한 영향을 미치는 것이 바닥마감재이다. 하지만 바닥마감재에 대한 탄성이나 물성을 측정하여 경량바닥충격음을 효과적으로 저감 하기 위한 연구는 부족한 실정이다. 이 연구에서는 사후 확인 제도 도입 이후 중요해 질 수 있는 바닥마감재의 경량바닥충격음 저감성능 예측하고자 하였다. 공동주택 바닥마감재로 사용되는 다양한 재료를 선정하여 실제 실험실에서 경량바닥충격음 차음성능을 측정하고 간이 실험으로 진동 전달특성 파악을 통해 경량바닥충격음 예측 가능성을 확인하고자 하였다.

• 한국생산제조학회지
• /
• 제19권5호
• /
• pp.684-690
• /
• 2010

A drum cam with rotational follower has a cam mechanism and it is mainly used in its application such as index table and ATC of machine tool. Also its use can reduce the backlash in its kinematic movement. To machine the drum cam with rotational follower, 5-axis CNC machine tool is generally used and its kinematic principle is included in it's design. Until now, the commercialized CAM software can't cover the application of the drum cam machining. Even if, some special software was developed for machining a drum cam, the post processing method for finish machining was not developed yet. And to overcome the problem, the form tool is still used on the tool path of rough machining. This study includes the induction of the post processing technique for the finish machining of drum cam on three 5-axis CNC machine tools, type AC, AB and BC. To prove the finishing geometric profile, the result was clearly verified through inspection and geometric measurement after direct machining of the drum cam in AC type 5-axis machine tool in this study.