• Composites Research
• /
• 제29권2호
• /
• pp.66-72
• /
• 2016

고온에서 열화학적 분해 현상을 겪는 고분자 기지 복합재료는 기지 내부의 기공도가 급격히 증가한다. 기공의 생성은 재료의 탄성 계수와 파손 강도를 감소시키며, 기공 내부의 가스 압력은 재료의 열기계적 거동에 영향을 준다. 본 논문에서는 기지 내부에 많은 기공이 포함된 일방향 섬유 강화 복합재료의 이차원 대표 체적 요소를 설정하고 유한요소 해석을 수행하였다. 이를 통해 기공 상태에 따른 복합재료의 유효 탄성 계수, 기공 탄성 계수, 파손 강도 등을 산출하였다. 특히, 기지 재료의 특성에 많은 영향을 받는 섬유 수직 방향의 파손 강도가 원래 기지 강도보다 현격히 낮게 산출되며, 기공도가 증가함에 따라 지속적으로 떨어지는 경향을 확인하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.1825-1828
• /
• 2008

A simple method for the fabrication of porous nano-master for antireflective surface is presented. In conventional fabrication methods for antireflective surface, coating method with low refractive index has usually been used. However, it is required to have high cost and long times for mass production. In this paper, we suggested the fabrication method of antireflective surface by the hot embossing process using the porous nano patterned master on silicon wafer fabricated by low-temperature anodic aluminum oxidation. Through multi-AAO and etching processes, nano patterned master with high aspect ratio was fabricated at the large area. Pore diameter and inter-pore distance are about 150nm and from 150 to 200nm. In order to replicate anti-reflective structure, hot embossing process was performed by varying the processing parameters such as temperature, pressure and embossing time etc. Finally, antireflective surface can be successfully obtained after etching process to remove selectively silicon layer of AAO master.

• 한국세라믹학회지
• /
• 제46권5호
• /
• pp.488-492
• /
• 2009

Porous frit-bonded SiC ceramics were successfully prepared at a temperature as low as $800^{\circ}C$ from SiC, frit, and microbeads (glass or polymer). The effects of SiC starting particle size and microbead addition on microstructure, porosity, and flexural strength were investigated. The addition of hollow glass microbead improved the strength of frit-bonded SiC ceramics without the loss of porosity by acting additional binder phase between SiC grains. The 65 ${\mu}m$-sized SiC resulted in lower porosity and higher strength than 50 ${\mu}m$-sized SiC because of higher packing density. Typical flexural strengths of frit-bonded SiC were 23 MPa at 46% porosity and 19 MPa at 49% porosity.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 춘계학술대회 논문집
• /
• pp.278-281
• /
• 2009

Proton exchange membrane is the key material for proton exchange membrane fuel cells (PEMFC). Currently widely-used perfluorosulfonic acid membranes have some disadvantages, such as low thermal stability, easy swelling, excessive crossover of methanol and high price etc. Other membranes, including sulfonated polymer, radiation grafted membranes, organic-inorganic hybrids and acid-base blends, do not satisfy the criteria for PEMFC, which set a barrier to the development and commercialization of PEMFC. Pore-filling type proton exchange membrane is a new proton exchange membrane, which is formed by filling porous substrate with electrolytes. Compared with traditional perfluorosulfonic acid membranes, pore-filling type proton exchange membranes have many advantages, such as non- swelling, low methanol permeation, high proton conductivity, low cost and a wide range of materials to choose. In this research, preparation methodology of pore-filling membranes by particularly using all hydrocarbon polymers and fuel cell performances with the membranes are evaluated.

• 대한의용생체공학회:학술대회논문집
• /
• 대한의용생체공학회 1990년도 춘계학술대회
• /
• pp.9-12
• /
• 1990

He impregnated a highly porous, knitted polyester (Dacron) graft with a biodegradable nonproteinaceous material, algin. This new vascular graft is blood tight but still retains high porosity in the body. It does not need to be preclotted with blood before implantation and has good tissue ingrowth and biological healing properties due to the high porosity. The algin impregnated graft was investigated by "in vitro" examinations in this study. It was characterized by ESCA analysis, SEM observation, and measurements of water permeability, algin coating weight, mechanical properties and whole blood clotting time. The water permeability of the graft was reduced more than 99% by the algin impregnation treatment without changing any mechanical properties. "In vivo" examinations of the algin impregnated vascular graft are on progress.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2011년도 춘계학술발표대회
• /
• pp.7.1-7.1
• /
• 2011

Nanoporous templates have been widely used for the development of new functional nanostructured materials suitable for electronics, optics, magnetism, and energy storage materials. We have prepared nanoporous templates by using thin films of mixtures of polystyrene-block-poly (methyl methacrylate) (PS-b-PMMA) and PMMA homopolymers. These templates have cylindrical nanoholes spanning the entire thickness of the film. Some applications of nanoporous templates are introduced: a) anti-reflective coating, b) the preparation of conducting polymer nanowires of poly (pyrrole), poly (3,4-ethylenedioxy-thiopene) onto a glass coated with indium-tin-oxide, and c) the separation membranes for biomaterials. We found that when the pore fraction of nanoholes in the film was ~0.68, almost zero reflectance at a specific wavelength, which can be changed with film thickness, was achieved at visible wavelengths Furthermore, ultra high density array of conducting nanowires was successfully prepared onto various substrates including flexible polymer. Due to highly alignment of polymer chain along the nanowire direction, the conductivity was much increased. Furthermore, these nanoporous films were found to be very effective for the separation of human Rhinovirus type 14 (HRV 14), major pathogen of a common cold in humans, from the buffer solution. We also found that when the pore size was effectively controlled down to 6 nm, a single file diffusion was observed.

• 한국고분자학회:학술대회논문집
• /
• 한국고분자학회 2006년도 IUPAC International Symposium on Advanced Polymers for Emerging Technologies
• /
• pp.194-194
• /
• 2006

Polymer light-emitting diodes(PLEDs) have great potential application in large area flat panel displays and general lighting so intense academic and industrial research, and impressive scientific and technological progress has been achieved in this field. However, the efficiency and stability of PLEDs till need to be improved in order to fully realize the advantages of low cost and ease of fabrication provided by organic materials. Here, we report our effort to enhance the PLED' s performance in two approaches : 1) Utilizing nano-structured materials such as nano particles, clay, nano porous silica in active layer 2) Modifying the device structure in nano scale to improve not only the device efficiency but also its stability.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• 제26권2호
• /
• pp.179-185
• /
• 2000

The purpose of this study was to develop an osteogenic, biodegradable material using polymer and BMP. It was designed to have structural function and be moldable, for the reconstruction of load bearing areas and deformities of various configurations. Bone apatite was added to Poly(L-lactide)(PLLA) and made porous for osteoconductability and ease of BMP loading. The materials, with or without BMP purified from porcine bone matrix, were evaluated in cranial bone defect models in rats for biocompatibility and bone regeneration capability. The following results were obtained: The PLLA-BMP material with BMP added to the polymer showed 30% healing of cranial bone defects in rats during the 2 weeks to 3 months period of observation. The moldable PLLA agent without BMP also showed 25% bone healing capacity. Although new bone formation was incomplete in the critical size defect of rat cranium, it can be concluded that the unique moldability of those agents makes them useful for the reconstruction of various bone defects and maxillofacial deformities.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2009년도 추계학술발표회 논문집
• /
• pp.79-84
• /
• 2009

Understanding the polymer adsorption in particle/binder/solvent system is important to achieve successful film products. While most of the reported work has dealt with the suspension microstructure, a few studies have focused on film formation. We investigated the effect of adsorption on film formation through measurement of adsorption amount in suspension and stress development in drying film with respect to mixing time ($t_m$). All of the adsorption amount (PVA), characteristic stress ($\sigma_{ch}$) exhibited similarities expressed by the form of $1-e^{t_m/{\tau}}$. The porous and non-unifonn dried film at short tm became close-packed and uniform with longer $t_m$. We found that polymer adsorption plays the key role in film fonnation as it introduces steric repulsion in suspension and suppresses the flocculation during solvent evaporation. We also found that the mixing time for the saturated polymer adsorption is the important variable to acquire the consolidated and uniform film microstructure.

• Macromolecular Research
• /
• 제11권2호
• /
• pp.104-109
• /
• 2003

A microcellular, which combines a rubber with the conventional formulation of styrene/divinylbenzene/sorbitan monooleate/water system, was prepared using high internal phase emulsion (HIPE) polymerization. Although the open microcellular foam with low density from the conventional HIPE polymerization shows highly porous characteristics with fine, regular and isotropic structure, the one having much smaller cell size is desirable for various applications. In this study, a polybutadiene was introduced to reduce the cell size with comparable properties. Major interests were focused on the effects of rubber concentration and agitation speed on the cell sizes and compression properties. Scanning electron microscopy was used to observe the microcellular morphology and compression tests were conducted to evaluate the stress-strain behaviors. It was found that the cell size decreased as rubber concentration increased, reflecting a competition between the higher viscosity of continuous phase and the lower viscosity ratio of dispersed to continuous phases due to the addition of high molecular weight rubber into the oil phase of emulsion. A correlation for the average cell size depending on agitation speed was attempted and the result was quite satisfactory.