• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2003.04a
• /
• pp.54-69
• /
• 2003

Print gloss is an important attribute of the final printed product. While past work has looked at the influence of key aspects of the coating structure on print gloss, a systematic study has not been reported. The coating roughness, porosity, and pore size are changed by using various combinations of coating materials and by calendering against rough plastic sheets. The print gloss is measured every tenths of a second right after printing, a few minutes after printing, and a few days afterwards. Roughness and porosity affect the print gloss for the first two seconds: this result shows that they influence the ink-film splitting event. Once ink film starts to level, roughness and pore size influences the level of print gloss within the first ten seconds after printing. Porosity modifies the evolution of print gloss for the next few minutes. The decrease in gloss at long times is found to correlate to surface roughness.

• Proceedings of the Korean Magnetic Resonance Society Conference
• /
• 2002.08a
• /
• pp.38-39
• /
• 2002

• Geomechanics and Engineering
• /
• v.23 no.4
• /
• pp.365-379
• /
• 2020

One of the leading causes for the damage of various underground structures during an earthquake is soil liquefaction, and among this liquefaction-induced uplift of these structures is a major concern. In this study, finite-difference modelling is carried out to study the liquefaction-induced uplift of an underground structure of 5 m diameter (D) with and without the replacement of the in-situ fine sand around the structure with the coarse sand. Soil replacements are carried out by three methods: replacement of soil above the structure, around the structure, and below the structure. The soil behaviour is represented using the elastic-perfectly plastic Mohr-Coulomb model, where the pore pressures were computed using Finn-Byrne formulation. The predicted pore pressure and uplift of the structure due to sinusoidal input motion were validated with the centrifuge tests reported in the literature. Based on numerical studies, an empirical equation is developed for the determination of liquefaction-induced maximum uplift of the underground structure without replacement of the in-situ sand. It is found that the replacement of soil around the structure with 2D width and spacing of D can reduce the maximum uplift by 50%.

• Environmental Engineering Research
• /
• v.17 no.2
• /
• pp.83-88
• /
• 2012

Currently, the technology of $CO_2$ capture and storage (CCS) has become the main issue for climate change and global warming. Among CCS technologies, the prediction of $CO_2$ behavior underground is very critical for $CO_2$ storage design, especially for its safety. Hence, the purpose of this paper is to model and simulate $CO_2$ flow and its heat transfer characteristics in a storage site, for more accurate evaluation of the safety for $CO_2$ storage process. In the present study, as part of the storage design, a micro pore-scale model was developed to mimic real porous structure, and computational fluid dynamics was applied to calculate the $CO_2$ flow and thermal fields in the micro pore-scale porous structure. Three different configurations of 3-dimensional (3D) micro-pore structures were developed, and compared. In particular, the technique of assigning random pore size in 3D porous media was considered. For the computation, physical conditions such as temperature and pressure were set up, equivalent to the underground condition at which the $CO_2$ fluid was injected. From the results, the characteristics of the flow and thermal fields of $CO_2$ were scrutinized, and the influence of the configuration of the micro-pore structure on the flow and scalar transport was investigated.

• Journal of Powder Materials
• /
• v.28 no.3
• /
• pp.216-220
• /
• 2021

The effect of tert-butyl alcohol (TBA) as a freezing solvent on the pore structure of a porous tungsten body prepared by freeze-drying is analyzed. TBA slurries with a WO3 content of 10 vol% are prepared by mixing with a small amount of dispersant and binder at 30℃. The slurries are frozen at -25℃, and pores are formed in the frozen specimens by the sublimation of TBA during drying in air. After hydrogen reduction at 800℃ and sintering at 1000℃, the green body of WO₃ is completely converted to porous W with various pore structures. Directional pores from the center of the specimen to the outside are observed in the sintered bodies because of the columnar growth of TBA. A decrease in pore directionality and porosity is observed in the specimens prepared by long-duration drying and sintering. The change in pore structure is explained by the growth of the freezing solvent and densification.

• Proceedings of the Korean Fiber Society Conference
• /
• 2003.10a
• /
• pp.100-100
• /
• 2003

An image processing algorithm has been developed in order to analyze the nanofiber web images obtained from a high magnification microscope. It has been known that precise pore detection on thick webs is extremely difficult mainly due to lack of light uniformity, difficulty of fine focusing and translucency of nanofiber web. The pore detection algorithm developed has been found to show excellent performance in characterizing the porous structure, thus being a promising tool for on-line quality control system under mass production. Since the images obtained from an optical microscope represent only web surface, a scale factor has been introduced to estimate the web structure as a whole. Resulting web structures have been compared to those by mercury porosimetry, especially in pore size distribution. It has been shown that those two structures have a strong correlation, indicating that scaling of a single layer web structure can be an effective way of estimating the structure of thick fiber webs.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.13 no.2
• /
• pp.73-78
• /
• 2003

The influence of calcination temperature on the pore structure of freeze dried silica gel derived from tetraethyl orthosilicate (TEOS) was investigated using $N_2$adsorption and mercury intrusion techniques. Freeze dried material contained not only 4-6 nm sized mesopores and 6-10 $\mu\textrm{m}$ sized macropores, but minor micropores. The change of pore structure due to the increase of calcination temperature was dependant upon the degree of densification.

• Journal of the Korean Ceramic Society
• /
• v.40 no.12
• /
• pp.1159-1164
• /
• 2003

Two processing routes (i.e., the gel casting and polymer preform routes) using polymer beads were studied to fabricate porous ceramics with a cellular structure. The gel casting route, comprising the gel casting of a ceramic slurry mixed with polymer beads, was found to be inadequate to produce porous ceramic bodies with a interconnected pore structure, due to complete coating of the slurry on the polymer beads, which left just isolated pores in the final sintered bodies. The polymer preform route, involving the infiltration of a polymer beads preform with the ceramic slurry, successfully produced porous ceramics with a highly interconnected network of spherical pores. The pore size of 250-300 $\mu\textrm{m}$ was demonstrated and the porosity ranged from 82 to 86%. This process is advantageous to control the pore size because it is determined by the sizes of polymer beads used. Another feature is the avoidance of hollow skeleton, giving a high strength.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.22 no.7
• /
• pp.448-453
• /
• 2010

Porous media containing complex fluid passage have especially large surface area per unit volume. This study is aimed to identify the heat transfer characteristics of high-porosity metal foams in a horizontal channel. Experiment is performed under various heat flux, velocity and pore density. Nusselt number decreases with higher pore density. Metal foams shows higher heat transfer coefficients than pin-fin structure with the same porosity. This is due to the more complex flow passage and larger heat transfer area based on the structure of the metal foams. The analysis on the pin-fin structure may not be suitable to the metal foam structure but should be identified extensively through further study.

• Journal of Electrochemical Science and Technology
• /
• v.12 no.2
• /
• pp.257-265
• /
• 2021

In this study, we report niobium (Nb) with hierarchical porous structure produced by a one-pot, HF-free electrochemical etching process. It is proved experimentally that a well-defined hierarchical porous structure is produced from the combination of a limited repetition of pulse etching and high concentration of aggressive anion (i.e., SO₄^2-), which results in hierarchical pores with high order over 3. A formula is derived for the surface area of porous Nb as a function of the hierarchical order of pores while the experimental surface area is estimated on the basis of the electrochemical gas evolution rate on porous Nb. From the comparison of the theoretical and experimental surface areas, an in-depth understanding was gained about porous structure produced in this work in terms of the actual pore shape and hierarchical pore order.