• 상하수도학회지
• /
• 제19권1호
• /
• pp.92-97
• /
• 2005

This research is to investigate the effect of the dual coagulant using inorganic coagulants($AICl3{\cdot}6H2O$) and polymer on the coagulant process. Jar-test was conducted by using Kaolin injected raw water. PDA(Photometric Dispersion Analyzer) equipment in order to analyze the size of the particles and the characteristics of the shapes. The change in the rate of sample ores' residual deposited after coagulants were also compared. According to the result derived from this experiment, the concentration of inorganic coagulant reduced 50% and the residual was lower by using dual coagulants compared to using single coagulant. However the dual coagulant required sufficient mixing time, and affected particle characteristics, with the effect of the injection order of coagulants, the simultaneous injection of inorganic coagulant and polymer showed the most effective in the particle removal.

• 한국환경보건학회지
• /
• 제24권2호
• /
• pp.104-109
• /
• 1998

The objective of this study was to examine the effect of polymer coating on the initial microorganism attachment and the biofilm growth. Such as nonion(polyacrylamine), anion(CMC-Na) and cation polymer coagulant(chitosan and PEI) were used for coating material of the support carrier(acryl plate). When polymer coagulant was coated with 5, 10, 20, 35, 50, 100 and 200 mg/l on the surface of acryl plate, initial microorganism attachment increased and optimum concentration for the attachment was 35 mg/l. Biofilm growth experiments were conducted with the substrate loading of 12.7gSCOD/$m^2\cdot$ day using RBC. The polymer coagulants such as CMC-Na, polyacrylamide, PEI and chitosan coating on the acryl plate facilitated the biofilm growth of microorganisms. Until the biofilm dry weight grows up to 0. 0038g/cm$^2$, biofilm growth on the plate coated with cation polymer like chitosan was better than that on the coated plate of nonion(polyacrylamine), anion(CMC-Na) polymer coagulant.

• Environmental Engineering Research
• /
• 제10권4호
• /
• pp.155-164
• /
• 2005

This study investigated the possibility of reducing the residual aluminum (Al) in the treated water using polymers. Two raw waters (lake and river water) and three kinds of polymers (coagulant, flocculant, and filtration aids) were used for this purpose. This study found that coagulation at the high dose did not necessarily lead to the high concentration of the residual Al in the treated water. The coagulation efficacy was found more important in determining the residual Al than the coagulant dose. The use of a polymer enhanced the removal of turbidity as well as the residual Al. The coagulant aid removed the dissolved Al as well as the particulate Al by helping the coagulation and the solid-liquid separation. The flocculant aid and the filtration aid preferentially removed the particulate Al while helping the solid-liquid separation. The filtration aid reduced the residual Al substantially more effectively than the flocculant aid. The polyamine-based coagulant aid (FL) showed the better performance in reducing the residual Al and turbidity than DADMAC (WT). The cationic flocculant aid with weak charge density and the medium molecular weight (SC-020) showed the best performance in reducing the residual Al.

• Elastomers and Composites
• /
• 제55권3호
• /
• pp.167-175
• /
• 2020

Various studies have been conducted to improve silica dispersion of silica filled tire tread compounds; among them, silica wet masterbatch (WMB) technology is known to be suitable for manufacturing silica filled compounds that have high silica content and high dispersibility. Till now, the WMB study is focused on the natural rubber (NR) or emulsion styrene-butadiene rubber (ESBR) that does not have a silica-affinity functional group, and a study of NR or ESBR having a silica-affinity functional group is still not well known. Unlike the dry masterbatch technology, the WMB technology can solve the problems associated with the high Mooney viscosity when applied to silica-friendly rubber. However, a coagulant suitable for each functional group has not yet been determined. Therefore, in this study, different coagulant applied silica WMB was prepared by applying calcium chloride, sulfuric acid, acetic acid, and propionic acid by using a carboxyl group functionalized reversible addition fragmentation chain transfer ESBR. The evaluation of the WMB compounds revealed that the calcium chloride added WMB compound showed excellent silica dispersion, abrasion resistance, and rolling resistance.

• 한국환경보건학회지
• /
• 제33권1호
• /
• pp.68-74
• /
• 2007

The objective of this study is to examine the effect of the coagulation and homogenization in bulking sludge thickening of paper manufacturing plant using DAF(Dissolved Air Flotation) and gravitational sedimentation. The effects of parameters such as dosage of coagulant and homogenization time were examined. The results showed that DAF and sedimentation was affected aluminum sulfate and anion polymer coagulant differently. At the optimum dosage of aluminum sulfate, thickening efficiency of DAF and sedimentation process were increase 1.25 time and 2.02 time, respectively. At the optimum dosage of anion polymer coagulant, thickening efficiency of DAF process was increase 1.35 time, but thickening efficiency at sedimentation was 1.06 time. When anion polymer coagulant of 0.5 mg/l was added in DAF process, water content of sludge was decreased from 96.6% to 90.7% in dewatering process using Buchner funnel test device. After homogenization(20500 rpm, 10 min), Sauter mean diameter of sludge floc was decreased from 631 ${\mu}m$ to 427 ${\mu}m$, however increase of flotation efficiency by DAF was only 1.09 time.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.3139-3143
• /
• 2007

The objective of this paper was to investigate the mixing characteristics of an three-stage inline coagulant mixing system experimentally. Wastewater samples of pH 8.5 and initial turbidity 1,000NTU were taken from a site of tunneling work. At the constant dosage, 0.36mL/L, of polymer as coagulant aids, the coagulation efficiency with the dosage of PAC as coagulant was about 4${\sim}$6% at 10 minutes after sampling. In the case of 2 different velocity gradient conditions, the efficiency of turbidity removal was increased about 6.5${\sim}$8% with increasing the dosage of coagulant while, the efficiency was increased about 20${\sim}$21.5% with increasing the dosage of coagulant aids. The efficiency of turbidity removal with the settling time after sampling was about 90% after 1 minute, and the efficiency was about 95% after 5 minutes.

• 한국막학회:학술대회논문집
• /
• 한국막학회 1995년도 춘계 총회 및 학술발표회
• /
• pp.26-27
• /
• 1995

Most of synthetic polymeric membranes used in ultrafiltration, reverse osmosis and microfiltration processes are prepared by phase inversion(or phase separation) technique. In this technique, a homogeneous polymer solution is cast into thin film or hollow fiber shape and then immersed into a nonsolvent coagulant bath. The exchange of solvent and nonsolvent across the interface between casting solution and coagu!ant can make the casting solution phase-separate and form a membrane with a symmetric or asymmetric structure. Because of importance of this technique in membrane field, many investigations have been dedicated to elucidate the mechanism of membrane formation by phase inversion technique.[1-10] These investigation have suggested that the structure formation and permeation properties of phase inversion membrane depend on the variables such as the nature and content of casting solution and coagulant, temperature of casting solution and coagulant, and the diffusional exchange rate of solvent and nonsolvent etc. which can be related to the thermodynamic and kinetic properties of the casting system. The variables such as the nature and content of casting solution can also be the important factor affecting the structure formation and permeation property of the phase inversion membrane.

• 유기물자원화
• /
• 제23권1호
• /
• pp.52-62
• /
• 2015

슬러지 응집제로서 폴리머, 제올라이트, 고령토, 황토, 키토산 등의 하수슬러지에 대한 응집효과 및 폴리머와 이들 응집제를 혼합한 물질의 응집효과를 검토하였다. 2,500~50,000 mg/L 농도에서 황토가 고령토, 제올라이트보다 하수슬러지에 대한 응집효율이 높았다. 제올라이트, 고령토, 황토 20,000 mg/L 처리의 응집효과는 폴리머 1,000 mg/L 처리의 응집효과보다 낮게 나타났다. 따라서 제올라이트, 고령토, 황토 단독 처리로는 현행 하수슬러지 탈수 시에 사용 중인 폴리머와 같은 응집효과는 기대하기 어려웠다. 키토산 역시 폴리머와 같은 1,000 mg/L 처리에서 응집효과가 현저하게 낮은 것과 고가의 구입비용을 감안하였을 때 키토산 단독처리는 현실적이지 않은 것으로 나타났다. 하수슬러지에 대한 지렁이처리법 적용에 유리한 응집제 조합은 '폴리머 80mg/L +고령토 또는 황토 500 mg/L + 키토산 10 mg/L' 으로 판단되며, 다음으로 '폴리머 80 mg/L + 고령토 또는 황토 500 mg/L' 조합으로 판단된다.

• 한국환경과학회지
• /
• 제7권2호
• /
• pp.217-222
• /
• 1998

Organics matters including algae are the major contaminants of Nak-dong river and it's concentration Is more Increasing now. The use of coagulants has been Incresed for the effective treatment of drinking water, and aluminum coagulants have been the most widely used in raw water treatment. However, when inorganic metal coagulant is excessively used for long period, it would result in secondary problems, such as increasing sludge production, enhancing the cost of water treatment process, and increasing concentration of residual metal, especially aluminum. Therefore, recently. in order to reduce the use of metal coagulant and enhance the coagulation effectiveness, several alternative coagulants, such as polymeric Inorganic coagulants and organic polymers, have been used In water treatment plants. The objectives of thins research were (11 to determine optimum dosage concentration and compare the coajuiation efnciency at various pH ranees with alum alone, alum+cationic polymer, and alum+anlonlc polymer, (21 to evaluate the amount of alum reduced by using organic polymer, (31 to maximize removal officiency of organic matter and minimize the concentration of residual aluminum.

• 한국환경기술학회지
• /
• 제19권6호
• /
• pp.570-575
• /
• 2018

폐수수탁처리업에 반입되는 산업폐수의 원수 성상이 매일 달라짐에 따라 전처리 공정인 응집침전공정의 효율적 운전이 어려운 실정이며, 이로 인해 후처리공정인 증발농축 및 대체 공정인 membrane 공정의 부하원인이 되고 있다. 이에 본 연구에서는 산업폐수의 효율적 처리를 위해 응집제 주입 방법별(단독주입, 동시주입, 순차주입, 역주입) 응집특성을 비교하기 위해 NaOH 주입 전 후 폐수 원수를 채수하여 실험하였다. 응집실험은 Jar-tester를 이용하여 진행하였다. 응집제주입방법별 TDS 제거효율은 순차주입(2.8 %) < 단독주입(3.9 %) < 동시주입(8.1 %) < 역주입(9.6 %) 순으로, TOC 제거효율은 단독주입(84.3 %) < 역주입(86.2 %) < 순차주입(88.6 %) < 동시주입(89.1 %) 순으로, 탁도 제거효율은 단독주입(99.7 %) < 순차주입(99.8 %) ${\fallingdotseq}$ 역주입(99.8 %) < 동시주입(99.9 %) 순으로 각각 나타내어, 이를 종합적으로 고려하여 판단한 결과 순차주입방법(무기응집제${\rightarrow}$고분자응집제)보다 무기응집제 및 고분자응집제를 동시에 주입하는 방법이 더 효율적인 것으로 나타났다.