• 한국농공학회:학술대회논문집
• /
• 한국농공학회 2003년도 학술발표논문집
• /
• pp.383-386
• /
• 2003

In this study, the MMA-modified paste mixed waste rubber powder, which has a small elastic modulus and a large modification, was produced by using the soft unsaturated polyester resin(UP) as a binder. Then the adhesive properties according to the matrices in both underwater and air-dry conditions and the hardening shrinkage according to the contents of shrinkage reducing agent(SRA) and of MMA were surveyed. The experimental results show that, regardless of humidity of matrices the adhesive strength of polymer concrete was larger than cement concrete. the adhesive strength of MMA content of 20% was larger than MMA content of 30%. regardless of matrix materials the adhesive strength in water condition were $20{\sim}30%$ comparing with the air-dry condition. The case of MMA content of 20% showed the largest adhesive strength. In the hardening shrinkage experiment, the hardening shrinkage reduced as MMA and SRA contents increased, and the decrease of the hardening shrinkage by SRA was larger.

• 폴리머
• /
• 제35권4호
• /
• pp.363-369
• /
• 2011

콘크리트 제조 시 사용되는 잉여수를 지연 흡수시키기 위하여 역유화중합법으로 중합된 가교 poly(sodium acrvlate) (cPSA)를 ethylene glycol dimethacrylate(EGDMA)로 표면 가교시켰다. cPSA의 제조에서 연속상은 paraffin liquid, 단량제는 8 M 농도의 NaOH 수용액으로 90% 중화된 acrylic acid(AA), 가교제는 N,N-methylene bisacrylamide(MBA), redox 개시제는 ammonium persulfate(APS)와 sodium metabisulfite(SMBS)를 사용하여 역유화중합법으로 제조하였다. 제조된 cPSA는 EGDMA플 사용하여 표면 가교 반응을 수행하였다. 시멘트 수용액에서 $Ca^{2+}$ 이온과 cPSA의 상호 작용을 관찰하기 위하여 FTIR spectroscopy 분석법을 사용하였다. 제조된 흡수제들을 탈이온수 $Ca(OH)_2$ 수용액(pH 12) 및 시멘트 포화 수용액에서의 팽윤비를 측정하였으며, cPSA는 2시간만에 팽윤이 완료되었지만, 표면이 가교된 cPSA-EGDMA는 3시간 후 팽윤이 거의 완료되는 것을 관찰하였다. 또한 합성한 cPSA-EGDMA를 첨가함으로써 시멘트의 응결시간과 모르타르의 압축강도 증가를 관찰하였다.

• Structural Engineering and Mechanics
• /
• 제39권4호
• /
• pp.499-520
• /
• 2011

The effectiveness of a technique for the repair of reinforced concrete members in combination with a technique for the repair of masonry walls of infilled frames, damaged due to cyclic loading, is experimentally investigated. Three single - story, one - bay, 1/3 - scale frame specimens are tested under cyclic horizontal loading, up to a drift level of 4%. One bare frame and two infilled frames with weak and strong infills, respectively, have been tasted. Specimens have spirals as shear reinforcement. The applied repair technique is mainly based on the use of thin epoxy resin infused under pressure into the crack system of the damaged RC joint bodies, the use of a polymer modified cement mortar with or without a fiberglass reinforcing mesh for the damaged infill masonry walls and the use of CFRP plates to the surfaces of the damaged structural RC members, as external reinforcement. Specimens after repair, were retested in the same way. Conclusions concerning the effectiveness of the applied repair technique, based on maximum cycles load, loading stiffness, and hysteretic energy absorption capabilities of the tested specimens, are drawn and commented upon.

• Geomechanics and Engineering
• /
• 제25권2호
• /
• pp.123-134
• /
• 2021

In this paper, the carbon fiber reinforced plastic (CFRP) grids embedded in polymer cement mortar (PCM) shotcrete (CFRP-PCM method) was conducted to repair the degraded tunnel linings with a cavity. Subsequently, the reinforcing effect of the CFRP-PCM method under different degrees of lining deterioration was quantitatively evaluated. Finally, the limit state design method of the M-N interaction curve was conducted to determine whether the structure reinforced by the CFRP-PCM method is in a safe state. The main results indicated that when the cavity is at the shoulder, the lining damage rate is more serious. In addition, the remarkably reinforcing effect on the degraded tunnel linings could be achieved by applying a higher grade of CFRP grids, whereas the optimization effect is no longer obvious when the grade of CFRP grids is too high (CR8); Furthermore, it is found that the M-N numerical values of the ten reinforcing designs of the CFRP-PCM method are distributed outside the corresponding M-N theoretical interaction curves, and these designs should be avoided in the corresponding reinforcing engineering.

• 한국농공학회논문집
• /
• 제57권4호
• /
• pp.11-19
• /
• 2015

The important properties of EVA (ethylene vinyl acetate) redispersible polymer was waterproof, densification of internal pore space of concrete and ball bearing and micro filler. Also, the significant role of polypropylene(PP) fiber was crack control and blockade of movement for deterioration factors. The most studies for EVA were limited in the field of mortar and PP fiber reinforced concrete had been studied in the state of being restricted unit water content, rich mix and mixing much of the fiber without considering construction site. Therefore, the control mix design were applied in ready mixed concrete using 10 % fly ash of total cement weight used in batch plant. On the basis of control mix design, EVA contents ranging from 0 % to 10 % of total cement weight and PP fiber contents ranging from 0 % to 0.5 % of EVA concrete volume were used in the mix designs. The results showed the maximum compressive strength value was measured at EVA 5.0 % and PP fiber 0.1 %, the minimum water absorption ratio was at EVA 10 % and PP fiber 0 %, the durability factor for freezing and thawing resistance was at EVA 5.0 % and PP fiber 0.3 % and the minimum weight reduction ratio of resistance to sulfuric acid attack was at EVA 10 % and PP fiber 0.5 % after curing age 42days. Meanwhile, From these results, PP fiber reinforced EVA concrete would be very benefit, if each optimal mix types were used in hydraulic structures, underground utilities and agricultural structures.

• 한국건축시공학회지
• /
• 제16권1호
• /
• pp.25-34
• /
• 2016

부도체로 알려져 있는 기존의 콘크리트에 전기 전도성 재료를 혼입하여 발열 콘크리트로서 개발하려는 연구가 90년대 이후 진행되어 왔다. 하지만 콘크리트 시험체의 발열 재현성 확보가 어려워 활발한 연구가 이루어지지 못했다. 이에 따라 본 연구에서는 융설용 재료로써 활용 가능한 발열 콘크리트 개발을 목적으로, 흑연, 금속분말, 혼화제를 혼입한 시멘트 페이스트 및 모르타르를 제작하여 $-2^{\circ}C$의 저온환경에서의 발열특성과 재현성을 평가하였다. 또한 미세화학분석을 통해 발현 재현성의 원인을 규명하고자 하였다. 실험 결과, 흑연과 고성능 AE감수제를 혼입한 시험체가 가장 우수한 발열 성능 및 재현 가능성을 보였다. 이에 따른 미세화학분석 결과, 고성능 AE 감수제 내의 폴리머 혹은 메타크릴산 성분이 흑연과 전기화학적 반응을 일으켜 발열 재현성능을 부여한 것으로 판단된다.

• 한국건축시공학회지
• /
• 제15권5호
• /
• pp.483-489
• /
• 2015

본 연구는 고온영역에 있어서 PCM의 역학특성의 기초적인 자료를 구축하는 것을 목적으로, 정온가열에 따른 온도별(100, 200, 400, $600^{\circ}C$) 잔존압축강도 특성에 대하여 실험하였다. 화재피해 이후의 특성을 살펴보기 위해 냉간시험을 실시하였으며 그 결과, PCM의 잔존압축강도는 폴리머의 종류에 관계없이 모두 감소하는 경향이 나타났다. 또한 함유량이 많을수록 $400^{\circ}C$의 고온영역부터 크게 감소하는 특성을 보였으며, PAE가 함유된 시험체가 EVA가 함유된 시험체보다 압축강도 기울기가 크게 나타나는 것을 확인하였다. 하지만 현재 PCM의 고온에 따른 역학적특성에 관한 연구는 상당히 미흡하기 때문에 본 연구와 더불어 보수방법 등에 대한 기초적인 연구가 반드시 선행되어야 할 것으로 판단된다.