• Journal of Pharmaceutical Investigation
• /
• v.19 no.1
• /
• pp.29-37
• /
• 1989

For the prevention of the aggregation during microencapsulation, the effects and role of polyisobutylene(PIB), as a protective colloid, were studied. The effects of sealant treatment on the microencapsulation were studied. Methyldopa was microencapsulated with ethylcellulose (EC) by polymer deposition from cyclohexane by temperature change using PIB. The EC-microencapsulated methyldopa was sealed with spermaceti. The dissolution of methyldopa was influenced by the drug to wall ratio. When PIB was used, low aggregation of microcapsules occurred and the surface was smooth with a few pores. Treatment of microcapsules with spermaceti retarded the release of methyldopa, the release being affected by the percentage of sealant used and the particle size of the product.

• Korean Journal of Food Science and Technology
• /
• v.39 no.2
• /
• pp.158-163
• /
• 2007

In this study, we prepared curdlan composite films and determined their properties in order to select the most appropriate setting methods, moisture barrier materials, and viscoelasticity enhancing materials. High set curdlan films with polyethylene glycol (PEG) showed higher tensile strength and moisture barrier properties than low set films. Films with oleic acid as a moisture barrier material had greater tensile strength, elongation and moisture barrier properties than films with acetylated monoglyceride (AMG). Lastly, films using polyisobutylene (PIB) as a viscoelasticity enhancing material showed higher elongation than films with polybutene (PB).

• YAKHAK HOEJI
• /
• v.43 no.4
• /
• pp.447-457
• /
• 1999

The purpose of this study is to prepare the adhesive type patch containing flurbiprofen, and to demonstrate the feasibility of flurbiprofen administration through the intact skin using adhesive type patch preparation. For this purpose, two pressure sensitive adhesives, Polyisobutylene(PIB) and $Gelva^{\circledR}737$, were selected from the chemical grade of polymers, and the adhesive type patches of flurbiprofen were prepared. The release rate of flurbiprofen from the PIB-based adhesive patch was higher than that from $Gelva^{\circledR}737$ based adhesive patch. The release rate of flurbiprofen from the PIB-based A-type patch with 1.0mm, 1.5mm or 2.0mm thicknesses followed the first order kinetics. In the skin permeation study, using male hairless mouse skin, a monophasic skin permeation profile was observed with 1% flurbiprofen loading dose. The inclusion of palmitic acid or SLS(0.25~0.5%) as an enhancer produced a remarkable enhancement in the skin permeation rate of flurbiprofen, and the percentile ratio of drug and enhancer appeared to be important for the effective enhancement. In the in vivo percutaneous absorption study, the plasma concentration of the optimal formulation was significantly (p<0.01) higher than that of the conventional cataplasma ($Bifen^{\circledR}$). These studies demonstrate a good feasibility of flurbiprofen administration through the intact skin using a transdermal patch, and show a possibility of the development of flurbiprofen patches.

• Applied Chemistry for Engineering
• /
• v.8 no.3
• /
• pp.425-429
• /
• 1997

Polyisobutenylsuccinic anhydride(PIBSA), an intermediate for the lubricating oil additive, was prepared by the reaction of polyisobutylene(PIB) with maleic anhydride (MA). The functionality, which indicates the extent of reaction of PIB-a and MA, was determined in the various reaction conditions : fuctionality was 0.98 under the reaction conditions of no solvent for 12 hours at $190^{\circ}C$, 0.21 in benzyl alcohol solvent for 12 hours at $190^{\circ}C$, and 0.03~0.20 with various Lewis acids such as $AlCl_3$, $SnCl_4$, $Et_2AlCl$, and $TiCl_4$. The fuctionality also depended on the structure of PIBs. As ${\alpha}$-olefin content (exo-form) in PIB increased, the fuctionality had a higher value. The structure of PIBSA prepared from PIB and MA was determined with FT IR and $^1H$ NMR spectroscopy. Two strong anhydride IR bands at 1782 and $1855cm^{-1}$ were obserbed and two IR bands at 1639 and $897cm^{-1}$ for unsaturated groups of PIB disappeared. The presence of the anhydride was difficult to find by $^1H$ NMR spectroscopy because the anhydride protons gave relatively small peaks over a 2.0~3.0 range. Polyisobutenylsccinimide (PIBSI), a lublicating oil additive, was prepared by the reaction of PIBSA with diaminoethane.

• Membrane Journal
• /
• v.14 no.4
• /
• pp.275-288
• /
• 2004

Carbon dioxide was absorbed into water-in-oil (w/o) emulsion composed of aqueous 2-amino-2-methyl-1-propanol (AMP) droplets as a dispersed phase and benzene solutions of polybutene and polyisobutylene as a continuous phase in a flat-stirred vessel to investigate the effect of non-Newtonian rheological behavior on the rate of chemical absorption of $CO_2$, where the reaction between $CO_2$ and AMP in the aqueous phase was assumed to be a pseudo-first-order reaction. It was expressed that PIB with elastic property made the rate of chemical absorption of $CO_2$ accelerated by comparison of mass transfer coefficient of $CO_2$ in the non-Newtonian liquid with that in the Newtonian liquid.

• Journal of Pharmaceutical Investigation
• /
• v.38 no.4
• /
• pp.223-228
• /
• 2008

The purpose of this study was to investigate the feasibility of developing transdermal drug delivery system (TDDS) for fentanyl used for the management of chronic cancer pain. The effect of type of pressure sensitive adhesive on the permeation of fentanyl from polyisobutylene (PIB), silicone and acrylic adhesive was evaluated. Due to the good adhesive force and relatively steady flux for 3 days, both acrylic and PIB adhesives were chosen for further study. The permeation rate of fentanyl was the highest from acrylic adhesive with hydroxyl functional group. Permeation rate increased linearly as the concentration of fentanyl in acrylic adhesive was increased from 2.5% to 10%. In case of PIB adhesive, crystals of fentanyl were developed above 5% drug load. $Crovol^{(R)}$ A40, $Crovol^{(R)}$ PK40 and Plurol $oleique^{(R)}$ provided higher flux of fentanyl.

• Membrane Journal
• /
• v.10 no.1
• /
• pp.19-29
• /
• 2000

To estimatc mutual diffusion coefficient for the analysis of mass transfer phenomena in polymer/solvent system, two models are proposed and the equations are derived. The estimates of mutual diffusion coefficients are obtained by two models suggested in this work and compared with and experimental data and Vrentas-Duda's. Vrentas-Duda's self diffusion coefficient was used for the mutual diffusion coefficient. Derivative of chemical potential on solvent was derived and used using original UNIFAC-FV and modified UNIFAC-FV. However, Vrentas-Duda's equation for mutual diffusion coefficient contains Flory-Huggins parameter x. For the derivative of chemical potential term, Vrentas-Duda assumed that parameter x was constant and independent of temperatures and concentrations The assumption is one of shortcoming in vrentas-Duda's mutual diffusion coefficient. New methods proposed in this work do not have such assumptions and simplifications. For the solvent of cyclohexane, n-pentane, and n-hexane in PIB(polyisolbutylene) and PMS-BR (poly(p-methylstyrene-co-isobutylene), new methods well correlate the experimental data at various temperatures and concentrations, and predicted the experimental data much better than Vrentas-Duda's for the PIB/toluene system. It is shown that new methods are excellent tools for correlating mutual diffusion coefficient data in polymer/solvent system over wide ranges of temperature and concentration without any assumptions or simplifications.

• Membrane Journal
• /
• v.6 no.1
• /
• pp.53-57
• /
• 1996

Polysulfone ultrafiltration membrane was coated with polyisobutylene(PIB) as a top layer to separate chlorinated hydrocarbons. The solubility parameter differences between PIB, water and perchloroethylene(PCE) or trichloroethylene(TCE) show that the solubility parameter difference between PIB and TCE or PCE is similar while that between PIB and water is far less, indicating that PIB is selective to chlorinated hydrocarbons. The pervaporation separation of TCE and PCE shows that TCE is concentrated more than four times, by PIB composite membrane, while PCE is concentrated more than thirteen times. This result shows that PIB composite membrane in this study seems to be an appropriate selective layer for the separation of TCE and PCE from aqueous organic solutions.

• Korea-Australia Rheology Journal
• /
• v.16 no.1
• /
• pp.35-45
• /
• 2004

Rates of chemical absorption of $CO_2$ in water-in-oil (w/o) emulsion were measured in a flat-stirred vessel at $25^{\circ}C$. The w/o emulsion was composed of aqueous monoethanolamine (MEA) droplets as a dispersed phase and non-Newtonian viscoelastic benzene solutions of polybutene (PB) and polyisobutylene (PIB) as a continuous phase. The liquid-side-mass transfer coefficient ($k_L$) was obtained from the dimensionless empirical equation containing Deborah number expressed as the properties of pseudoplasticity of the non-Newtonian liquid. $k_L$ was used to estimate the enhancement factor due to chemical reaction between $CO_2$ and MEA in the aqueous phase. PIB with elastic property of non-Newtonian liquid made the rate of chemical absorption of $CO_2$ accelerate compared with Newtonian liquid.

• Journal of Sensor Science and Technology
• /
• v.17 no.2
• /
• pp.143-146
• /
• 2008

Polymer-coated film SAW sensors have been fabricated and their sensing properties for toxic chemicals have been extensively investigated. Four types of the toxic chemical compounds of hydrogen cyanide(AC), carbonyl dichloride(CG), pinacolyl methylfluorophosphonate(GD), 2,2'-dichlorodiethylthio ether(HD) were used as target gases. SAW sensors using five different kinds of polymers were used to detect toxic chemicals and their gas sensing characteristics were investigated. The polymers used as the sensing materials were polyisobutylene(PIB), polyepichlorohydrin(PECH), polydimethylsiloxane(PDMS), polybutadiene(PBD) and polyisoprene(PIP). The recommendable mixing ratio of PIB, PECH, PDMS, PBD and PIP to solvents were 1:30, 1:40, 1:10, 1:30 and 1:30, respectively. The sensing characteristics of the SAW sensors were measured by using E-5061A network analyzer.