• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.1
• /
• pp.181-184
• /
• 2003

In this paper, we investigated the position-dependent stress distribution of indium-tin-oxide (ITO) film on Polycarbonate (PC) substrate by external bending force. It was found that there are the maximum crack density at the center position and decreasing crack density as goes to the edge. In accordance with crack distribution, it was observed that the change of electrical resistivity of ITO islands is maximum at the center and decrease as goes to the edge. From the result that crack density is increasing at same island position as face-plate distance (L) decreases, it is evident that the more stress is imposed on same island position as L decreases.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.1
• /
• pp.203-207
• /
• 2003

Ion implantation has been shown to significantly alter the surface properties of polymers. Polycarbonate(PC) and Polyimide(PI) were irradiated with 50keV $N^+$, $Xe^+$ ions to the fluences of $1{\times}10^{16}{\sim}3{\times}10^{17}\;cm^2$. The ion beam-induced modification of the electrical conductivity and the related structural features have been studied for polymers. The beam-induced chemical and structural modifications have been investigated by using X-ray Phooelectron Spectroscopy(XPS) and Fourier Transform-Infrared Spectroscopy(FT-IR), while the modification of the electrical properties was followed by performing a complete set of sheet resistance measurements. Samples irradiated at higher fluence showed a good conductivity, with a saturation value of $10^7{\Omega}/sq$. The XPS data demonstrate that the modification of the electrical properties is due to the progressive formation with increasing ion fluence of a dense amorphous carbon network, while PF-IR data reveal that material degradations through bond breaking are the main effects.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 추계학술대회 논문집
• /
• pp.247-250
• /
• 2009

This study considers the feasibility of using the low cost assembled separator. The graphite plate has been widely used as the separator in the field of PEMFCs(Polymer electrolyte membrane fuel cell) industry because of its excellent material properties such as good corrosion resistance, good electrical conductance and so on. However, there are some problems for the commercialization due to its poor cost effectiveness for the large volume manufacturing and lack of mechanical strength. From this respect, this study has focused on the manufacturing technology in order to reduce the price for the commercialization of separator. This study also shows that the assembled separator of the suggested structure, which is composed of grafoil and PC(PolyCarbonate) materials, could be manufactured at low cost enough for the mass production. The flow fields produced by cutting foils and the base plates of the separators were simply made by mechanical work.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.176-179
• /
• 2009

Injection molding is one of the most general manufacturing processes of polymers. The deformation of final molded parts occurs because of the change of temperature and pressure during injection molding process. The deformation of injection molded parts depends on many operational conditions, such as, melt temperature, injection speed, mold temperature, packing pressure, and the structure of mold. In the present paper, injection molding experiments were performed to find the process conditions to affect the average shrinkage in thickness direction and the replication ratio of fine patterns on the surface for the final injection-molded LGP samples. As a results, in the cases of PC(Polycarbonate), when the melt temperature was under $285^{\circ}C$, both average shrinkage and replication ratios were mainly influenced by packing pressure. However, the replication ratio was more influenced by melt temperature than packing pressure for the cases of higher melt temperature.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2053-2058
• /
• 2008

It was investigated thermal performances on two array types of a serial circulation and a two-way parallel circulation for six water-cooled cold plates covered with non-metallic material (polycarbonate, PC) to reduce weight of the cooling devices for humanoid robot cooling. Six cold plates attached on $10{\times}10\;mm^2$ copper base : $0.5{\times}0.5\;mm^2$ pin-finned surfaces of 1.5 mm high with 0.5 mm array spacing, was mounted on six copper heating blocks with isothermal conditions of $50{\sim}90^{\circ}C$, respectively. In order to compare thermal characteristics according to two circulation types, the surface temperatures of heating blocks and the cooling water temperatures at inlets and outlets of cold plates were measured. From the results, it was found that a two-way parallel circulation was better performance than a serial circulation in terms of total thermal resistance, total heat transfer rate, and surface temperature rises from $1^{st}$ heating block to last one for six multiple cold plates.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.265-265
• /
• 2010

고분자 소재(polycarbonate; PC)의 표면을 보호하고 광학적 특성을 유지하기 위해 산화물 다층 박막과 비정질 탄소 박막(diamond-like carbon; DLC)을 전자빔 증착(e-beam evaporation)과 이온빔 증착(ion-beam deposition)을 이용하여 고분자 소재에 코팅하였다. 전자빔 증착으로 코팅된 실리콘과 티타늄 산화물 다층 박막은 소재 표면에서 가시광선의 반사율을 낮추는 효과를 가지고 있어 다양한 광학 코팅분야에서 이용되고 있다. 비정질 탄소 박막은 경도가 높고 마찰계수가 낮기 때문에 기계부품의 수명향상을 향상하기 위해 주로 사용되며, 본 연구에서는 고분자 소재의 최상층에 코팅하여 보호막으로 이용하였다. 고분자 윈도우에 산화물 다층 박막을 코팅하면 코팅되지 않은 기판과 비교하여 투과율이 향상되었으며 보호막으로 코팅된 비정질 탄소 박막에 의해서 일어나는 투과율 저하를 부분적으로 상쇄하는 효과를 보였다. 산화물 다층 박막의 수는 광학 분야에서는 주로 5-7층을 이용하지만 고분자 소재는 코팅 공정이 길어지면 열 변형이 일어날 수 있기 때문에 산화막의 층수를 낮추는데 초점이 맞춰졌다. 5층과 3층으로 코팅된 산화물 박막 모두 투과율이 향상되었으며 3층에 비해서 5층의 투과율 향상효과가 큰 것으로 나타났다. 고분자 소재의 투과율은 평균 약 90%이었으며 산화물 다층 박막과 비정질 탄소 박막을 코팅한 후 투과율이 약 81%로 측정되었다. 비정질 탄소 박막과 산화물 다층 박막을 적절하게 설계하고 코팅한다면 고분자 소재의 보호막으로 이용될 수 있을 것으로 판단된다.

• 정보저장시스템학회논문집
• /
• 제7권1호
• /
• pp.25-30
• /
• 2011

In the last couple of years, the flexible optical disk(FOD) system that consists of a thin polycarbonate(PC) film of 95 ${\mu}m$ thick, a rigid stabilizer, and a high speed spindle motor has been spot-lighted as the next-generation optical system for archival use of digital data. The air film between the rotating disk and stabilizer provides a means for damping out the lateral disk vibrations. However, its damping-capability drops significantly as the rotational speed of the disk exceeds a specific limit and, eventually, the disk vibration propagates inward causing the whole span of the disk exhibits large vibration amplitudes. Based on the numerical simulations as well as the experimental results, the present work aims to evaluate the damping coefficient of the air-film near the outer region of the disk where the capillary type orifices are applied to the edge of the curved stabilizer.

• 생물환경조절학회지
• /
• 제32권1호
• /
• pp.57-63
• /
• 2023

본 연구에서는 새만금과 같은 간척지를 활용하여 대규모 첨단온실단지를 조성하는 경우 간척지의 환경적 특수성 중 높은 풍속에 따른 유리 단열재의 에너지 효율을 평가하였다. 현장에서 주로 사용되는 온실 단열재 중 4가지에 대한 평가 결과, 최대 37.4%의 에너지 차이를 보여, 온실 피복재의 선정이 중요함을 제시하였다. 이를 바탕으로 일반적인 내륙에서의 온실을 설계하는 것과 달리, 간척지에서는 내재해성 온실규격을 따라 시설을 설계하여야 하며, 에너지 소비량은 높아진 풍속과 재질을 고려하여 산정되어야 한다. 본 연구의 결과는 에너지 효율성을 온실 피복재의 종류와 풍속에 따라서 제시하고 있으며, 이는 대규모 첨단온실 조성 시 에너지 소비량을 예측하고, 이를 바탕으로 신재생에너지원을 포함하는 에너지 설계에 활용될 수 있다

• 한국건설순환자원학회논문집
• /
• 제8권1호
• /
• pp.33-40
• /
• 2013

최근 시멘트 생산 시에 발생하는 다량의 $CO_2$로 인한 환경문제가 심각한 실정이며, 이러한 환경문제를 해결하기 위해 고로슬래그 미분말과 같은 산업부산물을 시멘트 대체 재료로 사용한 알칼리 활성 슬래그 콘크리트에 대한 연구가 활발히 진행되고 있다. AAS 콘크리트는 상온에서 고강도 발현이 가능하지만 알칼리 반응으로 인한 빠른 응결시간과 유동성 손실로 인해 작업시간 확보에 어려움이 있는 것으로 알려져 있다. 본 연구에서는 알칼리 활성 콘크리트의 구조 부재 적용을 위한 기초 자료 확보를 위해 AAS 모르타르의 압축강도 및 유동 특성에 시멘트용 유동화제가 미치는 영향을 분석하였다. 물-결합재비(W/B)는 0.35로 고정하고 알칼리 활성화제로 수산화나트륨과 물유리를 사용하여 AAS 모르타르를 제조하였으며, 유동성 확보를 위해 4종의 유동화제인 나프탈렌(N), 리그닌(L), 멜라민(M), PC(P) 계를 각각 슬래그 질량대비 최대 2%까지 첨가하여 압축강도, 플로우, 초음파 속도를 측정하였다. 실험결과, 멜라민계 유동화제를 첨가한 경우 AAS 모르타르의 압축 강도 저하 현상 없이 유동성이 증진되는 것으로 나타났으며, 나프탈렌계와 PC계의 경우에는 유동성 개선효과가 미미한 것으로 나타났다.

• 한국물환경학회지
• /
• 제30권2호
• /
• pp.199-205
• /
• 2014

The knowledge on the migration of antimony (Sb) from PET bottles into the water is of greate concern. Antimony in all bottled water marketed in korea and in raw water was analyzed. The detection rate of antimony in total bottled water was 88 % and 100% in PET (Polyethylene terephthalate, PET), 55% in PC (Polycarbonate, PC) bottled water. 55% of raw water contained antimony. The average concentration of Sb in PET bottled water was $0.39{\mu}g/L$, higher than PC bottles ($0.20{\mu}g/L$) and the raw water ($0.22{\mu}g/L$). The migration of Sb into water that is stored in different conditions (room temperature, $45^{\circ}C$, and direct sunlight exposure) was investigated for 180 days. The migration tendency increased with the storage time and temperature. PET bottles showed a sharp increase of Sb concentration at $45^{\circ}C$, but there was no differences between the room temperature and sunlight exposure. The Sb migration in all simulated solution(deionized water, 4% acetic acid, and 20% ethanol) also increased with storage time and temperature. The Sb migration values ranged from 0.35 to $0.49{\mu}g/L$ in all simulated solution, which was far below the permissible korean migration level of $40{\mu}g/L$. There was a tendency that the number of re-use of a bottle and the amount of leaching were in inverse proportion.