• Journal of the Korea Concrete Institute
• /
• v.21 no.4
• /
• pp.409-417
• /
• 2009

In this study, autogenous crack healing and artificial crack healing using electrochemical electro deposition method were conducted to compare in the aspects of corrosion monitoring. Furthermore, the analysis of impressed voltage characteristics, galvanic current and linear polarization resistance comparison, and photo image processing technique were performed for quantitative comparisons of healing ratio. As a result, it was found that, in view of impressed voltage of artificial crack healing, the measured voltage was increased as time goes by. From the galvanic test results of artificial crack healing, the current vs. potential distribution value were formed widely in comparison with autogenous crack healing. In this point, it was shown that artificial crack healing has more eleatic resistance capacity than autogenous crack healing technique. Finally, it was found that artificial crack healing was 1.63 times higher than autogenous healing in view of crack healing ratio.

• Korean Journal of Metals and Materials
• /
• v.46 no.10
• /
• pp.691-699
• /
• 2008

Electrochemical characteristics of Ti-30Ta-xZr alloys coated with HA/TiN by using magnetron sputtering method were studied. The Ti-30Ta containing Zr(3, 7, 10 and 15wt%) were 10 times melted to improve chemical homogeneity by using a vacuum furnace and then homogenized for 24hrs at $1000^{\circ}C$. The specimens were cut and polished for corrosion test and coating, and then coated with HA/TiN, respectively, by using DC and RF-magnetron sputtering method. The analyses of coated surface and coated layer were carried out by using optical microscope(OM), field emission scanning electron microscope(FE-SEM) and X-ray diffractometer(XRD). The electrochemical characteristics were examined using potentiodynamic (-1,500 mV~ + 2,000 mV) and A.C. impedance spectroscopy(100 kHz ~ 10 mHz) in 0.9% NaCl solution at $36.5{\pm}1^{\circ}C$. The microstructure of homogenized Ti-30Ta-xZr alloys showed needle-like structure. In case of homogenized Ti-30Ta-xZr alloys, a-peak was increased with increasing Zr content. The thickness of TiN and HA coated layer showed 400 nm and 100 nm, respectively. The corrosion resistance of HA/TiN-coated Ti-30Ta-xZr alloys were higher than that of the non-coated Ti-30TaxZr alloys, whic hindicate better protective effect. The polarization resistance($R_p$) value of HA/TiN coated Ti-30Ta-xZr alloys showed $8.40{\times}10^5{\Omega}cm^2$ which was higher than that of non-coated Ti-30Ta-xZr alloys.

• Journal of the Korean Ceramic Society
• /
• v.49 no.5
• /
• pp.404-411
• /
• 2012

The reliability of solid oxide fuel cells (SOFCs) particularly depends on the high quality of solid oxide electrolytes. The application of thinner electrolytes and multi electrolyte layers requires a more reliable characterization method. Most of the investigations on thin film solid electrolytes have been made for the parallel transport along the interface, which is not however directly related to the fuel cell performance of those electrolytes. In this work an array of ion-blocking metallic Ti/Au microelectrodes with about a $160{\mu}m$ diameter was applied on top of an ultrathin ($1{\mu}m$) yttria-stabilized-zirconia/gadolinium-doped-ceria (YSZ/GDC) heterolayer solid electrolyte in a micro-SOFC prepared by PLD as well as an 8-${\mu}m$ thick YSZ layer by screen printing, to study the transport characteristics in the perpendicular direction relevant for fuel cell operation. While the capacitance variation in the electrode area supported the working principle of the measurement technique, other local variations could be related to the quality of the electrolyte layers and deposited electrode points. While the small electrode size and low temperature measurements increaseed the electrolyte resistances enough for the reliable estimation, the impedance spectra appeared to consist of only a large electrode polarization. Modulus representation distinguished two high frequency responses with resistance magnitude differing by orders of magnitude, which can be ascribed to the gadolinium-doped ceria buffer electrolyte layer with a 200 nm thickness and yttria-stabilized zirconia layer of about $1{\mu}m$. The major impedance response was attributed to the resistance due to electron hole conduction in GDC due to the ion-blocking top electrodes with activation energy of 0.7 eV. The respective conductivity values were obtained by model analysis using empirical Havriliak-Negami elements and by temperature adjustments with respect to the conductivity of the YSZ layers.

• Corrosion Science and Technology
• /
• v.14 no.2
• /
• pp.85-92
• /
• 2015

An on-line corrosion rate measurement system was developed using a personal computer, a data acquisition board and program, and a 2-electrode corrosion probe. Reliability of the developed system was confirmed with through comparison test. With this system, the effect of sodium nitrite ($NaNO_2$) as a corrosion inhibitor were studied on iron and aluminum brass that were immersed in sodium chloride (NaCl) solution. Corrosion rate was measured based on the linear polarization resistance method. The corrosion rates of aluminum brass and iron in 1% NaCl solutions were measured to be 0.290 mm per year (mmpy) and 0.2134 mmpy, respectively. With the addition of 200 ppm of $NO{_2}^-$, the corrosion rates decreased to 0.0470 mmpy and 0.0254 mmpy. The addition of $NO{_2}^-$ caused a decrease in corrosion rates of both aluminum brass and iron, yet the $NO{_2}^-$ acted as a more effective corrosion inhibitor for iron. than aluminum brass.

• Journal of the Korean Electrochemical Society
• /
• v.13 no.4
• /
• pp.246-250
• /
• 2010

In this study, nano-crystallized $Al_2O_3$ was coated on the surface of $LiFePO_4$ powders via a novel dry coating method. The influence of coated $LiFePO_4$ upon electrochemical behavior was discussed. Surface morphology characterization was achieved by transmission electron microscopy (TEM), clearly showing nano-crystallized $Al_2O_3$ on $LiFePO_4$ surfaces. Furthermore, it revealed that the $Al_2O_3$-coated $LiFePO_4$ cathode exhibited a distinct surface morphology. It was also found that the $Al_2O_3$ coating reduces capacity fading especially at high charge/discharge rates. Results from the cyclic voltammogram measurements (2.5-4.2 V) showed a significant decrease in both interfacial resistance and cathode polarization. This behavior implies that $Al_2O_3$ can prevent structural change of $LiFePO_4$ or reaction with the electrolyte on cycling. In addition, the $Al_2O_3$ coated $LiFePO_4$ compound showed highly improved area-specific impedance (ASI), an important measure of battery performance. From the correlation between these characteristics of bare and coated $LiFePO_4$, the role of $Al_2O_3$ coating played on the electrochemical performance of $LiFePO_4$ was probed.

• Journal of the Microelectronics and Packaging Society
• /
• v.22 no.4
• /
• pp.77-82
• /
• 2015

To increase the performance of solid oxide fuel cell operating at intermediate temperature ($600^{\circ}C{\sim}800^{\circ}C$), $Sm_{0.2}Ce_{0.8}O_2$ (SDC) thin layer was applied to the $La_{0.8}Sr_{0.2}Mn_{0.8}Cu_{0.2}O_3$ (LSMCu) cathode by sol-gel coating method. The SDC was employed as a diffusion barrier layer on the yttria-stabilized zirconia(YSZ) to prevent the interlayer by-product formation of $SrZrO_3$ or $La_2Zr_2O_7$. The by-products were hardly formed at the electrolyte-cathode interlayer resulting to reduce the cathode polarization resistance. Moreover, SDC thin film was coated on the cathode pore wall surface to extend the triple phase boundary (TPB) area.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.1300-1303
• /
• 2004

Copper는 낮은 저항률과 높은 Electromigration 저항 때문에 반도체 소자에 배선 재료로 사용된다. CMP 공정을 이용 하여 Cu wafer의 여러 가지 특성을 파악하기에는 wafer의 소모량이 많고 고가가의 비용이 예상 되므로, 본 논문에서는 비용절감을 위하여 wafer를 Disc로 대체 하고자 실험을 진행 하였고 Cu wafer와 Disc의 비료 방법은 우선 PM-5 (Genitech. co) 장비를 이용하여 removal rate의 차이점을 알 아 보았으며, 서로의 etch rate을 reomval rate과 비교하였다. EG&G 273A를 통하여 Cu wafer와 disc의 corrosion potential과 $R_p$ (Polarization resistance)값을 서로 비교 하였다. 이 논문에서는 이러한 것들을 서로 비교 하여, Cu wafer와 disc에서의 상관관계를 알고자 하였으며, 만약에 Cu wafer와 disc의 특성이 비슷하다면, Cu wafer 대신에 disc를 이용 하여 실험하여도 되는지에 관하여 조사 하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.327-327
• /
• 2010

In this paper, an investigation of factors affecting piezoelectric transformers is presented by ATILA software. These transformers are multi-layer piezoelectric transformers in square shape $28\;{\times}\;28\;mm$ and operate in first vibration mode for step-down function. The piezoelectric transformers were modeled in 3D-dimension and analyzed using finite element method in ATILA software, a popular software in piezoelectric analysis. Modal and harmonic modules were used in this process. Effective factors to the properties of piezoelectric transformers including different input electrode patterns, directions of polarization, sizes of connective comer, number of layers were examined on the simulated model using input voltage of 20 V and load resistance of $100\;{\Omega}$. Moreover, thermal analysis was also obtained with conditions of input voltage of 5 V and no-load.

• Journal of Korea Foundry Society
• /
• v.34 no.6
• /
• pp.187-193
• /
• 2014

In the present work, the effect of adding Ce on the corrosion behavior of Mg-4Al-2Sn-1Ca alloy was investigated. The studied alloys were fabricated by gravity casting method and a potentiodynamic polarization, A.C. impedance and hydrogen evolution tests were carried out in a 3.5% NaCl solution with pH 7.2 at room temperature to measure the corrosion properties of Mg-4Al-2Sn-1Ca-xCe alloys. The microstructure of the Mg-4Al-2Sn-1Ca alloy was composed of ${\alpha}$-Mg, Mg17Al12, Mg2Sn and CaMgSn phase. Also, a $Al_{11}Ce_3$ phase was newly formed by the addition of Ce. With an increase of the Ce contents, the microstructure became refined and the corrosion resistance improved.

• Journal of the Korean Ceramic Society
• /
• v.55 no.4
• /
• pp.358-363
• /
• 2018

To improve the polarization property of cathodes, which is the main factor limiting the performance of protonic ceramic fuel cells (PCFCs), $K_2NiF_4-type$ $Pr_2NiO_{4+{\delta}}$, which is expected to exhibit a triple conducting property (proton, oxygen ion, and hole conductions) was applied to PCFCs and its properties were investigated. Low-temperature microwave heat-treatment was used to achieve both sufficient interface adhesion between the electrolyte and the cathode layers and suppression of the secondary phase formation due to migration of elements such as barium and cerium. Through this fabrication method, a high performance of $0.82W{\cdot}cm^{-2}$ and low ohmic resistance of $0.06{\Omega}{\cdot}cm^2$ were obtained in an $Ni-BaCe_{0.55}Zr_{0.3}Y_{0.15}O_{3-{\delta}}$ | $BaCe_{0.55}Zr_{0.3}Y_{0.15}O_{3-{\delta}}$ | $Pr_2NiO_{4+{\delta}}$ single cell at $650^{\circ}C$. This result verifies that the $K_2NiF_{4+{\delta}}-type$ cathode shows good chemical compatibility which, in turn, will make it a potent candidate as a PCFC cathode.