• Journal of the Korean Wood Science and Technology
• /
• v.25 no.4
• /
• pp.39-44
• /
• 1997

4군데의 임반에서 선발된 라디에타 소나무를 공시목으로 두께 2.6mm와 1.4mm의 단판을 제작하였다. 단판을 조합하여 만들어진 합판의 크기는 $1200{\times}2400{\times}12.5mm$이었다. 12.5mm의 합판으로 단판의 성질에 따른 합판의 굽음을 조사하였던 바 단판의 성질과 합판의 굽음과의 관계는 낮은 상관관계를 보였다.

• Journal of Advanced Marine Engineering and Technology
• /
• v.19 no.3
• /
• pp.99-106
• /
• 1995

PWM(Pluse Width Modulation) induction motor drives are being used in greater numvers through a wide variety of industrial and commercial applications. In this paper, a new speed control algorithm (hybrid algorithm) for induction motor drives that uses regular sampled PWM and harmonic elimination PWM is presented. The hybrid algorithm in implemeted on the computer to obtain solutions from the calculation equations of the width of the pulses and the firing angles for the selected harmonic elimination. this paper describes the time delay effects and the suitable compensating methods moreover, optical transmission system for driving signals is proposed and is compared with general trnasmission system. The hybrid inverter was tested with induction motor, and these test results are shown that this hybrid inverter closely approximates and exhibits many of the desirable performance characteristic distortions and eliminated the objectionable harmonics. Finally, detailed experimental investigation of the proposed hybrid scheme in presented.

• Proceedings of the KIPE Conference
• /
• 2017.07a
• /
• pp.286-287
• /
• 2017

본 논문은 철도 차량 구동용 IPMSM 제어를 위한 속도 영역별 PWM 알고리즘을 제안한다. 철도 차량의 고속영역 제어는 인버터 전압 이용률을 최대화 할 수 있는 1-Pulse 제어 기법이 요구된다. 그러나, SPWM을 이용한 비동기 1-Pulse 제어는 출력 전류의 불균형을 초래한다. 따라서, 고속영역 제어를 위해 동기화 시킨 후 SPWM을 이용한 1-pluse 제어는 필수적이다. 본 논문에서는 비동기 모드로 제어를 시작하여 과변조 영역 이전에 지령 전압과 삼각파 주파수를 동기화 시킨 후 고속 영역운전을 하는 PWM 알고리즘을 제안한다. 본 논문에서 제안하는 알고리즘은 시뮬레이션으로 검증한다.

• Journal of Welding and Joining
• /
• v.29 no.1
• /
• pp.80-84
• /
• 2011

The weight reduction of the transportations has become an important technical subject Al and Al alloys, especially Al 5052 alloys have been being applied as door materials for automobile. One of the most widely known car weight-reduction methods is to use light and corrosion-resistant aluminum alloys. However, because of high electrical and thermal conductivity and a low melting point, it is difficult to obtain good weld quality when working with the aluminum alloys. Also, Pulse MIG welding is the typical aluminum welding process, but it is difficult to apply to the thin plate, because of melt-through and humping-bead. In order to enhance weld quality, welding parameters should be considered in optimizing the welding process. In this experiment, Al 5052 sheets were used as specimens, and these materials were welded by adopting new Cold Metal Transfer (CMT) pulse process. The proper welding conditions such as welding current, welding speed, torch angle $50^{\circ}$ and gap 0~1mm are determined by tensile test and bead shape. Through this study, range of welding current are confirmed from 100A to 120A. And, the range of welding speed is confirmed from 1.2m/min to 1.5m/min.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.4
• /
• pp.436-442
• /
• 2011

To obtain the engine output correctly is basically very important factor for estimating a engine performance. But, it has been reported that the IHP measured from electronic indicator such as MIPS(Mean Indication Pressure System) has a deviation compared to mechanical indicator. It was reported by authors that the uncertainty of crank angle for TDC position could be one of the reasons. In this paper, the uncertainty of crank angle for TDC position and its influence to engine output were investigated respectively about M/E and G/E for marine diesel engines. For the purpose, two sampling methods of pressure in cylinder were considered which were 'angle base sampling' and 'time base sampling'. Angle base sampling is real crank angle acquired from angle encoder which is attached to crank shaft and time base sampling is crank angle calculated by detected revolution with Z-pluse of encoder. Time base sampling is same method of MIPS. This paper concluded that time base sampling method is not suitable for obtaining the output of marine diesel engine on board because of instantaneous speed variation and load fluctuation. Also it is verified that the variation of engine speed by load fluctuation should be one of reasons additionally in case of M/E.