• Korean Journal of Soil Science and Fertilizer
• /
• v.42 no.5
• /
• pp.364-370
• /
• 2009

This study was conducted to survey, analyze on the compaction layer and the plow layer at Jeonbug and Jisan series paddy soil, which is the representative soil in fluvio-marine and local alluvium, respectively. The depths of surface soil were 12.6 and 12.7 cm in Jeonbug and Jisan series, respectively. A plowing depth was 10.5 cm. The properties of compaction layer in two soil series were as follows. The hardness were $14.7kg\;cm^{-2}(25.3mm)$ and $8.7kg\;cm^{-2}(22.1mm)$ in Jeonbug and Jisan series, respectively. The thickness were 22.3 cm and 17.8 cm in Jeonbug and Jisan series, respectively. The depth of soil compaction, which means depth from surface, were 15 and 20 cm in Jeonbug and Jisan series, respectively. The relationship between the hardness of compaction layer and the depth of surface soil showed negative correlation, however relationship between the hardness and the thickness of compaction layer showed positive correlation. Soil temperature was lower in compaction layer than in plow layer. This temperature differences between compaction layer and plow layer were from 1.0 to $2.5^{\circ}C$ in Jeonbug series and from 0.7 to 2.1 in Jisan series. The soil physical properties of compaction layer were higher in bulk density and solid phase and lower in porosity and gaseous phase than those of plow layer in all soil series. The soil chemical properties of compaction layer were higher in pH, content of available silicate, exchangeable calcium and magnesium but lower in total nitrogen, content of organic matter and available phosphate than those of plow layer in all soil series. Cation exchangeable capacity and content of exchangeable potassium were similar between compaction layer and plow layer in Jeonbug series, however, in Jisan series these were lower in compaction layer than in plow layer. Elution amount of inorganic nitrogen were lower in compaction layer than in plow layer in all soil series. The content of soluble Fe and Mn were plenty in compaction layer compared with plow layer and these tendency was apparent in Jeonbug series. The water depth decrease were fast until the latter part of June, and were slow as $1{\sim}3mm\;day^{-1}$ for July and August, and were fast again from september. Rice roots distributions as each soil series and tillage method were 25 cm at rotary plowing in Jeonbug series, 30 cm at deep plowing in Jeonbug series, and 20 cm at tillage in Jisan series. Dry weight per m2 at heading stage were much in order of deep plowing in Jeonbug series, rotary plowing in Jeonbug series, and tillage in Jisan series.

• Journal of Biosystems Engineering
• /
• v.12 no.3
• /
• pp.30-41
• /
• 1987

The geometrical shape of a plow bottom may be the most important factor affecting the performance of a plow for a given soil and operating conditions. There are various designs of the Jaenggi (Korean plow) available commercially, which may be different from each other and from the plow (Western plow) in respect to the shape and performance. This study was intended to investigate the geometrical characteristics of Jaenggi. The coordinate digitizer equipped with 3 potentiometers was designed and manufactured for measurement of the shape of curved plane of moldboard and share. The digitizer was connected to a microcomputer having the data acquisition system. This device was used to analyze the plow bottoms of 5 differently-made Jaenggis and one cylindrical plow. The results of the study are summarized as follows: 1. It was possible to measure easily and quickly the curved plane of plow bottom and to plot the view on three major plans using the coordinate digitizer electrically connected to a microcomputer system. 2. The shape of five Jaenggi bottoms analyzed could be characterized by the cutting angle having the range of $33-42^{\circ}$, the maximum share-lift angle of $41-50^{\circ}$, and the setting angle of moldboard wing of $46-70^{\circ}$. The most critical difference of the shape factors between the Jaenggi and the plow was found in the maximum share-lift angle, the former was more than twice as much as the latter. 3. The analysis of the shape of Jaenggi bottoms showed that the share projections on 3 major plans had a varied triangle, which was quite different from that of plow bottom. Especially, it was analyzed that the shape of furrow slice for the Jaenggi had a skewed rectangle, leaving a considerable height of the ridge at the furrow bottom. 4. The dihedral angle was similar range of $30-85^{\circ}$ for the all bodies investigated, but the directional angle was somewhat different from each other. The difference in directional angle was $5^{\circ}$ for the plow, $20^{\circ}$ for the Jaenggi A and $30^{\circ}$ for the Jaenggi B. 5. Area of the spherical representation region was 0.0328 for the plow, 0.1194 for the Jaenggi A and 0.1716 for the Jaenggi B. This may indicate that the plow came close to a working surface and the Jaenggi A and the Jaenggi B departed from a working surface to a somewhat greater extent.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.29 no.4
• /
• pp.313-320
• /
• 2009

This experiment was conducted to evaluate the effect of tillage system and fertilizer type on the forage yield and quality of Italian ryegrass. This experiment was a $2{\times}2$ factorial arrangement for two tillage systems (tillage and no-tillage) and two fertilizer type (chemical and manure compost). The plant height, dry matter (DM) content, DM yield, TDN (total digestible nutrients) yield, and CP (crude protein) yield have significant differences in tillage system of Italian ryegrass. Italian ryegrass cultivated with tillage (plow and rotary till) had lower plant height, DM yield, TDN yield and CP yield than no-tillage, while its DM content showed the opposite results. However, there were no significant differences in the results on fertilizer types. Neutral detergent fiber (NDF) and acid detergent fiber (ADF) contents were significantly higher in no-tillage compared to tillage. However, there was no significant difference in CP content on tillage system. TDN and relative feed value (RFV) were higher in tillage than no-tillage system (p<0.01). The TDN content was lower when using manure as fertilizer. No significant effects were observed for NDF and RFV in fertilizer type of Italian ryegrass. Based on the results of this study, tillage system and fertilizer type affected forage quality as well as forage yield. Forage yield of no-tillage was higher compared to tillage.

• Korean Journal of Agricultural Science
• /
• v.42 no.3
• /
• pp.183-189
• /
• 2015

Plant root penetration through soil profile is restricted by compacted layer such as plow pan under conventional tillage. For detecting the compact layer, we made a graduated T-shape probe and measured compared between the depths with rapid change in feeling hardness of hand penetration using T-shape probe and with a rapid increase of penetrometer cone index. On upland crops, including red pepper, corn, soybean and cucumber, plow pan depth ranged from 10 cm to 25 cm depth. The effective rooting depth (ER) had significant correlation with the plow pan depth (PP) except soils with the shallow ground water and/or poorly drained soil. The regression equation was ER = 0.9*PP ($R^2=0.54^{**}$, N = 14) with the applicative PP range of 10-25 cm.

• Journal of Biosystems Engineering
• /
• v.16 no.3
• /
• pp.219-227
• /
• 1991

This paper concerns with experimental verification of the theory on the safe VHP positions presented in the first part of this study. In the experiment, tillage operation was conducted using a plow mounted to the threepoint hitch and the forces acting on the hitch points were measured. Using the data from the test tractor and plow, computer simualtion was also conducted and its results were compared with those obtained from the field experiment. The comparison showed a reasonable agreement between the two results, by which the theoretical method for the determination of safe VHP positions for steering control can be verified. Some guidelines for expanding the safe VHP region were finally proposed.

• Journal of Biosystems Engineering
• /
• v.27 no.6
• /
• pp.521-528
• /
• 2002

Rotary and plow implements are mainly utilized for the tillage operation in Korea, and a implement control system for agricultural tractors was designed and fabricated to improve the working accuracy and efficiency. The control system was composed of three units: 1) sensors fur detection of angle of liftarm, draft force, engine rpm, tillage depth and so on, 2) a controller, and 3) hydraulic circuits, which included solenoid valves and so on, for operation of three point linkage and implements. The control system can control the speed(high and low speed) of implements by adjusting input flow rates of the hydraulic cylinder which was controled by two speed valve, which was composed of a solenoid valve and a orifice. Indoor experiments were conducted to evaluate response characteristics of the designed implement control system under experimental conditions of various engine nm, two kinds of input flow rates of the cylinder and some input frequency. The results of experiments showed the response characteristics sufficient to use as the implement control system fur agricultural tractors.

• Journal of Drive and Control
• /
• v.17 no.1
• /
• pp.27-36
• /
• 2020

The aim of this study is to design a simulation model for an electric All-Wheel-Drive (AWD) tractor to evaluate the performance of the selected component and agricultural work ability. The electric AWD tractor consists of four motors independently for each drive wheel, and each motor is combined with an engine generator, a battery pack, and reducers. The torque data of a 78 kW-class tractor was measured during plow tillage and driving operation to develop a workload cycle. A simulation model was developed by using commercial software, Simulation X, and it used the workload as the simulation condition. As a result of simulation analysis, the drive system, including an electric motor and reducers, was able to cope with high load during plow tillage. The SOC (State of Charge) level was influenced by the output power of the motor, and it was maintained in the range of 50~80%. The fuel consumed by the engine was about 18.23 L during working on a total of 8 fields. The electric AWD tractor was able to perform agricultural work for about 7 hours. In the future study, the electric AWD tractor will be developed reflecting the simulation condition. Research on the comparison between the simulation model and the electric AWD tractor should be performed.

• Korean Journal of Agricultural Science
• /
• v.47 no.4
• /
• pp.1147-1158
• /
• 2020

The purpose of this study was to measure the engine torque and rotational speed of a 67 kW class agricultural tractor according to tire type during plow tillage and to analyze the gear strength of the driving shift for the tractor. A field test was performed under the condition with a single tire (Test A) and dual tires (Test B) to increase the ground width of the rear tires. A load monitoring system was developed, and the engine torque and rotational speed were measured using controller area network (CAN) communication. The engine torque and rotational speed during plow tillage were calculated as the equivalent torque and speed using Palmgren Miner's rule. As a result, the equivalent torque and speed in Test A and Test B were 181.0 Nm and 1,913 rpm and 206.1 Nm and 2,130 rpm, respectively. As the ground width of the rear tire was increased, the bending stress in Test B was about 9.9 to 10.5% higher than that of the Test A, and the contact stress was about 4.6 to 4.9% higher than that of the Test A. Under all conditions, the safety factor for the bending and contact stress was 1 or more. Thus, the driving shift gears for the dual tire type are considered safe.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.28 no.4
• /
• pp.307-314
• /
• 2008

No comprehensive tillage system of corn (Zea mays L.) has been conducted in Korea. Therefore, this experiment was carried to determine soil characteristics, weed and forage production in tillage system of corn. Plot was allotted to one of four treatments in a randomized block design using tillage system. The four treatments were (T1) conventional tillage, plow and rotary till, (T2) rotary till, (T3) disk till, and (T4) no-till system. In soil characteristics before planting and after harvest of corn, pH and organic matter at planting date was higher than at harvest date, however, there were no difference among tillage system. Days from planting to silking of no-till was the longest among tillage system. Lodging resistance of disk and no-till were higher than conventional and rotary till due to its thicken stem diameter. Main weed in corn field are barnyard grass (Echinochloa crusgall), velvetleaf(Abutilon avicennae), crabgrass (Digitatia saguinalis), and redroot pigweed (Amaranthus retroflexus). Weed population was lower in no-till than others tillage system. Dry matter (DM) content and ear percentage of conventional and rotary till were higher than others in corn field. However, DM and total digestible nutrients (TDN) yields of disk and no-till were higher than those of conventional and rotary till. Therefore, disk and no-till are more suitable in corn silage system because of high lodging resistance and forage yield, and low weed population.

• Korean Journal of Organic Agriculture
• /
• v.24 no.4
• /
• pp.699-717
• /
• 2016

This study was carried out to investigate the effect of no-tillage on sequential cropping supported from recycling of first crop ridge on the growth of pepper plant and physical properties of soil under green house condition. 1. Degree of crack on soil by tillage and no-tillage Soil cracks found in ridge and not found in row. At five months of tillage, crack number and crack length in length ridge were 3 and 37~51 cm in tillage. Maximum width and maximum depth in length ridge were 30 mm and 15.3cm in tillage. Crack number and crack length in width ridge were 7.5 and 7~28 cm in tillage. Maximum width and maximum depth in width ridge were 29 mm and 15.3 cm in tillage. At a year of no-tillage, crack number and crack length in length ridge were 1.0 and 140~200 cm in tillage. Maximum width and maximum depth in length ridge were 18 mm and 30 cm in a year of no-tillage. Crack number and crack length in width ridge were 11 and 6~22 cm in a year of no-tillage. Maximum width and maximum depth in width ridge were 22 mm and 18.5 cm in a year of no-tillage. Soil crack was not found at 2 years of no-tillage in sandy Jungdong series (jd) soil. Soil crack was found at 7 years of no-tillage in clayish Jisan series (ji) soil. 2. Penetration resistance on soil Penetration resistance was increased significantly at no-tillage in Jungdong series (jd). Depth of cultivation layer was extended at no-tillage soil compared with tillage soil. Penetration resistance of plow pan was decreased at 1 year of no-tillage compared with than tillage soil. Penetration resistance was linearly increased with increasing soil depth at tillage in Jisan series (ji). Penetration resistance on top soil was remarkably increased and then maintained continuously at no-tillage soil. 3. Drainage and moisture content of soil Moisture content of ridge in top soil was not significant difference at both tillage and no-tillage. Moisture content of ridge in 20 cm soil was 14% at no-tillage soil and 25% at tillage soil. 4. Change of capacity to retain water in soil Capacity to retain water in top soil was not significant difference at 1 bar both tillage and no-tillage. Capacity to retain water in soil was slightly higher tendency in 1 year and 2 years of no-tillage soil than tillage soil. Capacity to retain water in soil was increased at 15 bar both tillage and no-tillage. Capacity to retain water in subsoil was slightly higher tendency at 1 bar and 3 bar in 2 years of no-tillage than tillage soil and a year of no-tillage soil.