• 한국자기학회지
• /
• 제11권1호
• /
• pp.1-7
• /
• 2001

열연판을 모재로 하여 압연 및 열처리 공정을 조합한 공정을 3회 냉간압연법을 사용하여 최종두께 100$\mu\textrm{m}$로 제작한 방향성 규소강대에 대하여, 직류자기 특성 및 결정입자의 열처리 의존성, 결정방위 등을 조사하였다. 그 결과, (110)면이 거의 시료 전체표면에 성장하는 것이 관측되었으며, B$_{8}$은 1.9 T정도, 평균$\alpha$각은 약 4.6$^{\circ}$이었다. 향후 약간의 (001)조직의 집적도 개선이 추가된다면, 염가의 열연판을 모재로 사용하여 기존의 방향성 규소강판의 경우보다 훨씬 제조공정수를 단순화함으로써, 경제성이 우수한 방향성 극박 규소강대를 제작할 수 있는 가능성을 확인하였다.

• 소성∙가공
• /
• 제33권3호
• /
• pp.208-213
• /
• 2024

Ni-based superalloys have exceptional performance in high-temperature strength, corrosion resistance, etc, and it has been widely used in various applications that require corrosion resistance at high-temperature operations. However, the relatively expensive cost of the Ni-based superalloys is one of the major hurdles. The corrosion-resisted alloy(CRA) clad materials can be a cost-effective solution. In this study, finite element analysis of the hot rolling process for manufacturing of the Alloy 625/API X65 steel CRA clad plates is conducted. The stress-strain curves of the two materials are measured in compressive tests for various temperature and strain rate conditions, using the Gleeble tester. Then, strain hardening behavior is modeled following the modified Johnson-Cook model. Finite element analysis of the hot rolled cladding process is performed using this strain rate and temperature dependent hardening model. Finally, the thickness ratio of the CRA and base material is predicted and compared with experimental values.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1993년도 춘계학술대회논문집; 한국과학연구소, 21 May 1993
• /
• pp.65-70
• /
• 1993

본 연구에서는, 제철 열간 압연기에서 slab가 진입, 추출시 충격으로 인한 진 동에 의해 두께 조절용 위치센서가 오작동을 하는 원인을 규명하고 그 해결 책을 제시하고자, 기존 AGC Top Plate와 위치 감지센서의 작동 상태 및 진 동특성을 검정하였고, 문제점을 발견하여 각각의 구조를 개선, 재측정하여 개선정도를 확인하였다. Disk형 AGC Top Plate는 직경을 줄이고, 두께를 늘 여 자체 진동을 감소시켜, Plate 진동에 의한 위치센서의 오작동 원인 및 이 에 의해 제어 유압펌프에 Feedback되어 top부 제어계에 발생하는 Hunting현 상을 줄였다. 위치센서는 내부 Spring의 초기변형량을 증가시켜 내탄성에너 지량을 증가시켜, 센서자체의 진동 및 측정시 나타나는 여진현상을 제거하였 다. 본 연구를 통한 측정결과로는 최대 82.7%의 제진효과와 여진현상의 제거 효과를 보았다.

• 대한금속재료학회지
• /
• 제46권4호
• /
• pp.189-198
• /
• 2008

The changes in microstructure and mechanical properties of AZ31 alloy subjected hot-rolling process were investigated. The AZ31 plates fabricated by horizontal continuous casting process were prepared and have hot-rolled from 30 mm to 1 mm in thickness under different processing conditions. At the rolling temperature of $400^{\circ}C$, little surface and side crack was observed up to 20% reduction rate. As total reduction and reduction rate increase to more than 75% and 20% pass, respectively, Grains were more uniformly refined through overall thickness, and particularly lots of shear bands were appeared to be inclined at less than $20^{\circ}C$ along the rolling direction. Average grain size of less than $5{\mu}m$ and tensile properties of YS ${\geq}$ 250 MPa, UTS ${\geq}$ 300 MPa and El. ${\geq}$ 13% were acquired for hot-rolled AZ31 sheets without post-heat treatment. Maximum intensity of (0002) pole figure was decreased with an increase in reduction rate, indicating the improvement of texture by means of high reduction rate.

• Journal of Welding and Joining
• /
• 제27권3호
• /
• pp.92-96
• /
• 2009

Metallic sandwich plate has many good properties such as high specific stiffness, high specific strength, good impact absorptivity, effective thermal insulation and soundproofing. In our study, a new bonding method, 3-layer roll projection welding, is introduced to fabricate the metallic sandwich plate. The new method uses a pair of roll electrodes like the seam welding, and projection welding is made at two internal interfaces of the 3-layer weldment consisting of a structured inner sheet and a pair of skin sheets. During the welding process, skin sheet temperature are measured to produce metallic sandwich plate with uniform and good quality. But it is difficult to observe or measure the temperature at the welding points during welding process because the welding points exist at the internal interfaces. Therefore FEM numerical analysis using ABAQUS is conducted to estimate the generated heat at the welding points with different welding conditions.

• 소성∙가공
• /
• 제27권5호
• /
• pp.289-295
• /
• 2018

The profile ring rolling process can realize various ring shapes unlike conventional rectangular cross-sectional ring products. In this paper, the defective groove in the bottom surface of L-shaped ring products was analyzed. Grooves are generated by non-uniform external forces due to profile main roll and initial blank shape. Process parameters such as the motion of dies and working temperature were determined. Mechanism of groove formation was analyzed by FE simulation on the basis of local external forces acting on the blank. Analysis results were similar to the groove actually occurring in the production line. Based on results of the analysis, two solutions were proposed for the groove. The position of the base plate supporting the blank was adjusted and edge length of the main roll was extended to suppress growth of grooves. It has been verified that groove was improved by applying two proposed methods in the shop-floor.

• 열처리공학회지
• /
• 제13권5호
• /
• pp.346-354
• /
• 2000

Effect of Nb addition on the phase transformation behavior was studied through continuous cooling transformation tests after reheating(reheating CCT) and deforming(deforming CCT) the 0.07%C-1.3%Mn-0.015%Ti-(0~0.08)% Nb steels. Transformation temperatures for deforming CCT were lower than those for reheating CCT, and the critical cooling rate for bainite transformation during deforming CCT was lower than that during reheating CCT. These enhanced hardenability for deforming CCT was considered to come from the sufficient solid solution of Nb in austenite during high temperature reheating before deformation. With Nb addition, the phase transformation temperature decreased, the bainite formation was enhanced, and the hardness of steel increased. Furthermore, these phenomena were more remarkable for deforming CCT than for reheating CCT. From the results, Nb-Ti bearing low carbon steel was considered to be a very favorable alloy system with good strength/toughness balance by recrystallization control rolling process.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 제5회 압연심포지엄 신 시장 개척을 위한 압연기술
• /
• pp.72-82
• /
• 2004

The deformation mechanism of hexagonal close-packed materials is quite complicate including slips and twins. A deformation mechanism, which accounts for both slip and twinning, was investigated for polycrystalline hop materials. The model was developed in a finite element polycrystal model formulated with initial strain method where the stiffness matrix in FEM is based on the elastic modulus. We predicted numerically the texture of Mg alloy(AZ31B) sheet by using FEM based on crystal plasticity theory. Also, we introduced the recrystallized texture employed the maximum energy release theory after rolling. From the numerical study, it was clarified that the shrink twin could not be the main mechanism for shortening of c-axis, because the lattice rotation due to twin rejects fur c-axis to become parallel to ND(normal direction of plate). It was showed that the deformation texture with the pyramidal slip gives the ring type pole figure having hole in the center.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.119-122
• /
• 2004

Since a derailment of rolling stocks results in huge losses in properties and lives, the measurement of a derailment coefficient is a very important test item to estimate the running safety of rolling stocks. For a measurement of the derailment measurement of forces between the wheel and rail a measuring wheel-set should be made first. The process to make a measuring wheel-set has some stages for correct measurement. They are as follows; a finite element analysis of a wheel to find a position of holes at which vertical force shall be measured, a finite element analysis for the position of strain gauges.

• 대한기계학회논문집
• /
• 제3권4호
• /
• pp.133-142
• /
• 1979

The fracture toughness of a hot rolled 100 mm thick SS41 steel plate was investigated for various crack ratios and thichnesses using the method of J-integral. The experiments were performed on an MTS machine and the crack initiation point was detected by using an electricl impedance method. The J-integral computed at the initiation point of the slow stable crack growth was almost constant within the range of crack ratios tested. The fracture toughness thus obtained was $J_{1c}/=27.0kgf/mm$ for specimens having fracture plane parallel to the rolling direction and 35.5kgf/mm for those perpendicular to the rolling direction. The J- integral computed at maximum load point was found to be unsuitable for fracture toughness determination, becaese of large variation depending on the crack ratio and thickness. It was also found that the slow stable crack growth increases as the thickness and/or crack ration of the specimen decrease.