• Bulletin of the Korean Chemical Society
• /
• v.26 no.6
• /
• pp.882-886
• /
• 2005

Copper(II) ion-selective PVC membrane electrode based on 2-mercaptobenzoxazole as a new ionophore and o-nitrophenyl octyl ether (o-NPOE) as plasticizer is proposed. This electrode revealed good selectivity for $Cu^{2+}$ over a wide variety of other metal ions. Effects of experimental parameters such as membrane composition, nature and amount of plasticizer, and concentration of internal solution on the potential response of $Cu^{2+}$ sensor were investigated. The electrode exhibits good response for $Cu^{2+}$ in a wide linear range of 5.0 ${\times}$ 10−.6-1.6 ${\times}$ $10^{-2}$ mol/L with a slope of 29.2 ${\pm}$ 2.0 mV/decade. The response time of the sensor is less than 10 s, and the detection limit is 2.0 ${\times}$ $10^{-6}$ mol/L. The electrode response was stable in pH range of 4-6. The lifetime of the electrode was about 2 months. The electrode revealed comparatively good selectivities with respect to many alkali, alkaline earth, and transition metal ions.

• Journal of the Korean Ceramic Society
• /
• v.37 no.1
• /
• pp.26-32
• /
• 2000

Preparation and characteristics of a matrix retaining electrolyte using SiC whisker, PES binder, and NMP(n-methyl-2-pyrrolidone) as a non-volatile solvent for a phosphoric acid fuel cell were investigated. The conditions of binder and plasticizer, and the effects of substituting a volatile solvent by a non-volatile solvent were also studied. The minimum amount of the binder was about 17 wt% for the proper bubble pressure and surrounding SiC whiskers. And the maximum amount of the plasticizer was about 10wt% to be fitted into the polymer chain of the binder. The matrix prepared by using a non-volatile solvent needed longer time to dry, and its pore size was smaller compared with that of the matrix prepared by using volatile solvent. The small pore size resulted in decrease of the overall pore volume. The ionic conductivity in the condition of the same thickness was decreased due to decrease of phosphoric acid absorbancy. As the internal resistance of the electrolyte increased, the fuel cell performance slightly decreased.

• Proceedings of the KIEE Conference
• /
• 1994.11a
• /
• pp.205-208
• /
• 1994

The purpose of this study is to research and develop solid polymer electrolyte(SPE) for Li secondary battery. PEO-$LiClO_4$ electrolyte with plasticizer is very unstable. Passivation phenomena in polymer electrolyte cell was described by the SPL model. The time dependance of the impedance indicates that a passivation layer grows rapidly on the Li surface. However, the growing of passivation layer on the Li surface can be restrained by addition of zeolite to the PEO electrolyte. It suggested that addition of zeoliteto to the PEO-$LiClO_4$ electrolyte effectively controls the formation of a passivation layer on Li electrode.

• Macromolecular Research
• /
• v.17 no.8
• /
• pp.591-596
• /
• 2009

To trace the plasticizing effects of propylene glycol (PG) on poly(vinyl alcohol) (PVA), the rheological properties of PVA solutions in dimethyl sulfoxide (DMSO) and the physical properties of PVA films were discussed in terms of PG content. Both properties were closely related to the hydrogen bond breaking effects of PG The 6 and 12 wt% PVA solutions containing PG exhibited Bingham behavior, which was more noticeable at lower plasticizer content and higher polymer concentration. The 6 wt% PVA solutions containing more than 30 wt% PG showed a sudden decrease of viscosity over the frequency range of 0.08 and 0.2 rad/s. However, the 12 wt% PYA solutions showed no viscosity reduction even at a PG content up to 40 wt%. The glass transition temperature of the PVA/PG films was almost linearly decreased with increasing PG content but an abrupt reduction was observed at a plasticizer content 30 wt%, suggesting that the hydrogen bond breaking effects of PG on PVA became dominant between 20 and 30 wt%. This effect was further supported by the similar tendency of the tensile properties.

• Journal of the Korean Applied Science and Technology
• /
• v.16 no.4
• /
• pp.317-322
• /
• 1999

Transparent films were prepared using the sol-gel process by mixing TEOS with PVA solution that was solved in EtOH and distilled water homogeneously. HCl, $CH_3COOH$ and $NH_4OH$ were used as catalysts of the sol-gel process, and for improving the flexibility of films glycerol was used as plasticizer. In case of each catalyst, transparency and tensile strength were increased, and glass transition temperature (Tg) was shifted to higher temperature with increasing TEOS ratio. Also, in case of adding the plasticizer, the flexibility of films was increased. On the contrary, transparency, thermal stability and tensile strength were decreased with increasing HCl and $NH_4OH$ ratio. Also, the range of being made of film type was expanded when $CH_3COOH$ was used than HCl and $NH_4OH$.

• Korean Journal of Food Science and Technology
• /
• v.30 no.5
• /
• pp.1097-1106
• /
• 1998

Biodegradable edible films were prepared from rice protein concentrates (RPC) made from rice wine meal by alkaline extraction and isoelectric precipitation. The effect of film forming solution pH and plasticizers were studied, and cross-linkers were added to improve mechanical properties and water vapor permeabilities (WVP) of films. Films could be formed within pH $8{\sim}11$ with tensile strength (TS) of 4.3{\sim}5.7\;MPa$. Films produced under pH 11 had the highest TS (5.7 MPa) and the lowest WVP $(0.44\;ng{\cdot}m/m^2{\cdot}s{\cdot}Pa)$. Added glycerol, polyethylene glycol 200 (PEG) and its mixture (GLY:PEG=50:50) as plasticizers also affected the mechanical properties and WVP of films. TS and elongation at break (E) of films at various plasticizer levels were $5.5{\sim}1.0\;MPa$ and $3.6{\sim}24.3%$, respectively. At the same plasticizer concentration, the highest TS was observed when glycerol was used whereas the highest E was measured when mixture was used as plasticizer. WVPs of films with thickness of $60\;{\mu}m$ were $0.39{\sim}0.54\;ng{\cdot}m/m^2{\cdot}s{\cdot}Pa$. WVP of films decreased as the ratio of glycerol/PEG 200 was decreased, and WVP increased as the total amount of plasticizer added to the films increased. Film strength was improved by the addition of small amount of sodium hydrogen sulfate, succinic anhydride, ascorbic acid and citric acid, whereas TS of films containing $0.5{\sim}2.0%$ of NaCl and $CaCl_2$ were lower than those without the salts. The highest TS (6.3 MPa) was achieved with films containing 0.1% of succinic anhydride.

• Journal of Korean Ophthalmic Optics Society
• /
• v.18 no.1
• /
• pp.11-17
• /
• 2013

Purpose: To improve glasses temple's insert processibility of CA/PEG blend, triacetin with higher specific heat values in the processing temperature range is used as second plasticizer. Methods: The total amount of plasticizer is fixed at 30 wt% by CA. To determine optimal CA/PEG/triacetin blend for glasses frame, blends with different composition ratio were examined by various analysis: thermal properties, mechanical properties, glossiness. Results: Specific heat of the CA/PEG blend increased as the content of triacetin. In CA/PEG/triacetin blends, as triacetin concentration is increased, glass transition temperature is decreased and heat conservation rate of composites is increased. Furthermore, CA/PEG/triacetin blend exhibited higher mechanical properties and similar gloss characterization with CA/PEG blend. Conclusions: It is possible to improve the processibility inserting metal support to CA temple through varying the weight ratio of PEG/triacetin. The extruded sheets of CA/PEG/triacetin blend had better glossiness and mechanical properties than those of CA/PEG blend.

• Proceedings of the Korean Society of Food Hygiene and Safety Conference
• /
• 2002.05a
• /
• pp.127-131
• /
• 2002

Migration of di-(ethylhexyl)phthalate (DEHF) from PVC food packaging materials detected plasticizer into food simulanting solvents(4% Acetic acid, 8% Ethanol, 50% Ethanol, 95% Ethanol, Heptane) were studied. For executing this study ,2 PVC food packaging materials detected DEHP were used. Analysis was by GC-FID and GC-MSD(selected ion monitoring) for DEHP, and optimized for quantification of plasticizer. The recovery of DEHP into food simulanting solvents were min. 87.4${\pm}$ 3.6 ∼ max. 109.9 ${\pm}$ 10.7% respectively. Following exposure to food simulants 95% Ethanol for 24hours at 60$^{\circ}C$ the migration results of 1020.90 ${\pm}$ 10.15$\mu\textrm{g}$/g, 563.54 ${\pm}$ 5.60$\mu\textrm{g}$/dm$^2$and 73.51 ${\pm}$ 5.09$\mu\textrm{g}$/g 149.22 ${\pm}$ 10.34$\mu\textrm{g}$/dm$^2$were detected from the container for lunch and for stock fish respectively.

• Journal of the Korean Applied Science and Technology
• /
• v.35 no.3
• /
• pp.816-825
• /
• 2018

Recently, it was emerged to need the necessity of LPG residues management due to the finding some substances such as rust. This study is performed to investigate the characteristics of LPG residues in the production and distribution stage of LPG. For the qualitative analysis of LPG residues, it was operated to be set up the analysis conditions(the flow rate, etc) of GC-MS and was performed to analyze the component of LPG residues. From the analysis result using GC-MS, it was shown that the component of LPG residues was turned out the plasticizer to be used in the rubber manufacturing process. The inorganic components of LPG residues were analyzed using ICP-OES. At the results of inorganic analysis, it was shown that the Si element was detected, which was presumably derived from defoamers used mainly in the LPG production. Also, the P and Zn element, which are estimated to be components of grease additives used for filling facilities, were also partially detected. No trace of rusting was detected in the LPG residues in the production and distribution stages analyzed in this study. But, as plasticizers and grease additives can affect to the LPG fuel system in vehicles, it will be necessary to use the proper quality of rubber and to expand the use of low boiling grease additives.

• Journal of Korean Ophthalmic Optics Society
• /
• v.20 no.1
• /
• pp.1-7
• /
• 2015

Purpose: For optimizing properties of final glasses frame, the aim of this study is to examine the correlation of processing conditions and properties of cellulose acetate (CA) sheets through the investigation of properties of CA sheets prepared under processing steps. Methods: The properties of CA sheets were investigated in terms of different glasses frame processing conditions, bending process, barrel process, and ultrasonic cleaning process. CA sheets prepared through the sequential processing were examined by various analysis: gloss, mechanical properties, thermal properties. Results: After barrel process, hardness and tensile strength of CA sheet were increased. However, bending strength and impact strength were decreased. It is suggested the CA sheet had became rather stiff state (brittle). Also, in degradation temperature region of plasticizer, about 3% of reduction in plasticizer weight was confirmed upon TGA analysis. Conclusions: Glasses frame process, especially in the barrel process have a profound influence on the properties of CA sheet owing to reduction of total amount of plasticizer.