• Journal of Korean Society on Water Environment
• /
• v.22 no.1
• /
• pp.45-50
• /
• 2006

This study was performed to evaluate the air lift reactors (ALR) by variations of HRT and recycling rate. Air lift reactor was composed of bioreactor and clarifier above it. To remove organic matters and nitrogen through the formation of microbic film and filtration, bio-filter reactors were filled with clay, glass, bead, waste plastic, respectively. Influent wastewater was fed to biofilter reactor, and effluent wastewater from bio-filter reactor was injected ALR again, instead of adding external carbon source. Effluent BOD concentration was satisfied with lower than 10 mg/L in recycling rate 100% regardless of the variation of HRT and the kinds of media materials. In HRT 4 hr, recycling rate 100%, BOD removal efficiency rate was from about 85 to 90%, COD removal efficiency rate was higher than 90%. Effluent TN concentration was satisfied with less than 20 mg/L, if HRT was maintained by over than 6 hr regardless of recycling rate and media materials. Over than HRT was 4 hr, microbes concentration in air lift reactor was maintained over than 2,500 mg/L constantly, not sensitive to environmental condition, and organic removal was effective as it was higher.

• Proceedings of the Korean Fiber Society Conference
• /
• 1998.04a
• /
• pp.63-66
• /
• 1998

The steady growth in the use of plastic materials in packaging applications has caused an increasing concern about the environment and the problem of solid waste disposal. Therefore, the recycling of plastics is the very important problem, which must be solved technically and environmentally [1]. It is technically feasible to recycle, recover and reuse all of the plastics discarded, but economics limit the degree of recycling at this time.(omitted)

• Proceedings of the Korean Institute of Resources Recycling Conference
• /
• 2004.05a
• /
• pp.123-127
• /
• 2004

• Proceedings of the Korean Institute of Resources Recycling Conference
• /
• 2006.05a
• /
• pp.113-118
• /
• 2006

• Journal of the Korea Organic Resources Recycling Association
• /
• v.21 no.3
• /
• pp.74-81
• /
• 2013

In this study, the separation efficiency of wind power selector (the direction of the air flow of the air to perform gravity separation method) of municipal solid waste which was landfilled was investigated to reduce amount of waste that is designed to increase the recycling rate of wastes for the ANSYS CFX Program's numerical methods with wind through the separator. When a suction device designed to suction 1000mL of a plastic bag, the separation efficiency was 100% and when the wind speed was 0.9 m /sec or more and when the wind speed was 1.6 m / sec or more, the efficiency of plastic bottles in a mixture of 500mL and 1500mL plastic bottle waste was 100% and the aluminum screening efficiency of 250mL aluminum can was 100 % when the wind speed was 2.3 m / sec. In the last, 5mm thick compressed aluminum can efficiency was 90 % when the wind speed was 2.4 m / sec.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.12 no.4
• /
• pp.95-104
• /
• 2004

A styrene solution of waste expanded polystyrene with a crosslinking agent and an initiator was used as a binder for waste wood-plastic composite panels. The waste wood-plastic composite panels are prepared with various binder contents and filler-binder ratios by using a hot press molding method. The apparent density of the composite panels is increased with increasing binder content and filler-binder ratio, while their water absorption and expansion in thickness are decreased with increasing binder content and filler-binder ratio. The maximum flexural strength and wet flexural strength of the composite panels are obtained at a binder content of 35% and a filler-binder ratio of 0.8. Decreases in the flexural strengths of the composite panels due to water immersion at 20 and $100^{\circ}C$ are hardly recognized at binder contents of 30% or more.

• Resources Recycling
• /
• v.7 no.2
• /
• pp.16-22
• /
• 1998

Recently, the new technology for the recycling of waste plastics as an alternative he1 of blast furnace ha been developed. In this shldy, the test of plastics injection into a tuyere af the foundry blast furnace were carried out. The injection rate of plastics far this tcst facility war expressed as follows, ${W}_{s}=0.265\frac{{delta}PA}{U}_{g}$, where. Ws, AP, A and Ug are plastic conveying ratc (kgisec), pressure drop between feed hopper and blaqt pressure (alm), cross sectional area of conveying pipe (mi) and superficial velocity of transport air (mhzc) respcctiuely. From the results of semi-continuous test operation during 96 hours, the replacement raho mned out to be 1.38 according to the injection rate of 6. 4 kg-plasticsit-p. With increasing the rate of plaslics injcchon, the content of hydrogen in top gas became increased and the brick temperahlre at bzlly was also increased due to Lhe changes ot the combustion zone shape.

• Resources Recycling
• /
• v.22 no.3
• /
• pp.50-56
• /
• 2013

Recycled plastic composites of ABS/PE (50/50 and 20/80) and ABS/GF (90/10) were fabricated from plastic components of waste LCDs and effects of PE composition on elongation of ABS/PE composites were investigated. Increased PE contents improved elongation of the composite from 2.4% to 13%, which was attributed to increased crystalline behavior of the ABS/PE composite afforded by ductile PE fraction: SEM fractographs showed some sign of plastic deformation of PE matrix before ductile fracture of the composites.

• Resources Recycling
• /
• v.33 no.1
• /
• pp.48-57
• /
• 2024

This study aimed to improve utilization of the Class C vinyl waste generated in rural areas based on a preliminary investigation on the use of eco-powder, generated through pyrolysis, as a raw material for plastic. The efficiency of pre-processing treatments in controlling ash content of the generated eco-powder and its effect on the basic properties of manufactured plastic were evaluated. The basic properties included ash content of the compressed eco-powder at different levels of ash content, impact strength, flexural strength, and tensile strength. The experimental results confirmed that pre-processing improved the separation efficiency of soil particles and vinyl waste through physical impact. The eco-powder with ash content of less than or equal to 26% was found to satisfy the target performance during impact strength, flexural strength, and tensile strength evaluation. Thus, it was confirmed that the Class C vinyl waste, having low utilization and recovery rates, could be effectively utilized as a plastic raw material after optimum thermal treatment and physical processing using the eco-powder.

• Resources Recycling
• /
• v.15 no.1 s.69
• /
• pp.37-45
• /
• 2006

For treating a huge amount of plastic waste with the environment problem, pyrolysis of plastic waste into alternative fuel oil is one or important issue in recycling methods. This study was introduced over the trend or generation of plastic waste, in Korea pyrolysis technology in domestic and foreign countries, basic technology in pyrolysis process and new technology of pyrolysis developed in KIER (Korea Institute of Energy research). The characteristics of process developed in KIER are the continuous loading treatment or mixed plastic waste with an automatic control system, the minimization of wax production by circulation pyrolysis system in non-catalytic reactor, the reuse of gas produced and the oil recovery from sludge generated in pyrolysis plant, which have greatly the advantage economically and environmetally. The experiment result data in 300 ton/yr pilot plant showed about $81\;wt\%$ liquid yield for 3 days continuous reaction time, and also the boiling point distribution of light oil (LO) and heavy oil (HO) produced in distillation tower was a little higher than that of commercial gasoline and diesel, respectively.