• 한국항해항만학회지
• /
• 제31권3호
• /
• pp.271-279
• /
• 2007

선체구조는 기본적으로 판부재의 조합으로 이루어져 있으며, 이러한 판부재의 하중분담 능력 혹은 최종강도 평가는 선체구조의 합리적인 설계 및 구조의 안정성 평가에 있어서는 아주 중요하다. 또한, 선체구조를 구성하고 있는 구조요소들은 작용외력에 대하여 개별적으로 작용하지 않으며 전체적으로 연속거동을 하게 된다. 실제 선박에서의 붕괴형태 중 한가지는 종방향 굽휨에 의해서 갑판 혹은 선저부에 좌굴 및 소성붕괴이다. 그래서, 합리적인 설계에서는 이러한 급작스런 붕괴형태를 방지하기 위하여 좌굴 및 소성붕괴 거동을 파악하는 것이 아주 중요하며, 실제 선박에서는 갑판부와 선저부에서는 하중분담 능력을 증가시키기 위하여 여러개의 종보강재를 가진 보강판 구조의 설계를 하게 된다. 본 연구에서는 선체 판넬구조의 모델링 방법에 따른 최종강도 거동의 차이를 분석하여, 합리적인 모델링영역을 규명하고자 한다. 사용된 해석 모델은 실제 상선의 이중저구조에서 사용되는 판넬에서 채택하였으며 유한요소해석 모델링 시 3가지 단면형상에 대해 각각 6가지 서로 다른 해석모델을 적용하였으며, 이때 보강재의 단면형상을 변화하였다. 본 연구의 목적은 압축하중이 작용하는 선체 보강판구조에서 해석영역에 대한 좌굴 및 최종강도 거동의 특성을 분석하였다.

• 한국강구조학회 논문집
• /
• 제21권6호
• /
• pp.597-608
• /
• 2009

본 연구에서는 접합부 특성이 고려된 공간프레임의 대변형 탄소성해석법에 관한 내용을 기술한다. 이 해석법은 유한변형을 고려한 대변형 탄성해석법에 기초한 것으로 부재의 재료적 탄소성, 접합부 반강접 특성을 추가적으로 고려하였다. 절점의 유한변형은 오일러의 개념으로 부터 유도되었으며, 부재좌표계에서 계산된 부재변형은 보-기둥식에 대입하여 부재력을 계산하였다. 부재변형은 부재축변형과 휨에 의한 축변형효과를 함께 고려하여 계산하였으며, 부재축력의 휨강성, 비틀림강성에 대한 효과를 고려하여 항복함수를 계산하였다. 재료는 완전 탄소성으로 가정하였고, 항복은 부재 양단부에서 집중하여 발생하는 소성힌지의 개념을 사용하였다. 부재 접합부 반강접 특성은 지수모델이나 선형모델을 적용하였고, 접합부 특성이 고려된 탄소성 후좌굴해석을 수행하기 위해 호장법을 사용하였다. 본 연구내용의 정확성 및 효율성을 검증하기 위해 공간프레임에 대한 해석을 수행하였다.

• 한국해양공학회지
• /
• 제17권5호
• /
• pp.39-47
• /
• 2003

A study of the structural strength evaluation on the doubler plate, considering various load cases that were subjected to in-plane and out of plane combined load, has been performed through the systematic evaluation process. In order to estimate the proper static strength of doubler plate for various load cases, elasto-plastic large deflection analysis is introduced, including the contact effect between main plate and doubler. The characteristics of stiffness and strength variation are discussed, based on the results. In order to compare the doubler structure with the original strength of main plate, without doubler, simple formulas for the evaluation of the equivalent flat plate thickness are derived for each load case, respectively, based on the additional series of analysis of flat plate structure. Using these derived equations, the thickness change of an equivalent flat plate is analyzed according to the variation of various design parameters of doubler platesome design guides are suggested in order to maintain the original strength of main plate without doubler reinforcement. Finally, correlation between derived equivalent flat plate formula and the developed buckling strength formulas are discovered, and these relations are formulated for the future development of simple strength evaluation formula of general doubler plate structure.

• 소성∙가공
• /
• 제14권8호통권80호
• /
• pp.718-724
• /
• 2005

An efficient finite element method has been introduced for analysis of metallic sandwich plates subject to bending moment. A full model 3-point bending FE-analysis shows that the plastic behavior of inner structures appears only at the load point. The unit structures of sandwich plates are defined to numerically calculate the bending stiffness and strength utilizing the recurrent boundary condition for pure bending analysis. The equivalent models with the same bending stiffness and strength of full models are then designed analytically. It is demonstrated that the results of both models are almost the same and the FE-analysis method incorporating the equivalent models can reduce the computation time effectively. The dominant collapse modes are face buckling and face yielding. Since the inner dimpled structures prevent face buckling, sandwich plates with inner dimpled shell structure can absorb more energy than other types of sandwich plates during the bending behavior.

• Journal of Welding and Joining
• /
• 제25권1호
• /
• pp.49-56
• /
• 2007

Prediction and control of the thermal distortion is particularly important for the design and manufacture of welded thin plate panel. In this study, experiments and computations are performed to analyze effect of a hole configuration and a specimen size on distortion. In addition, this study aims to develop a thermal elasto-plastic simulation using finite element method to predict distortion, with particular emphasis on buckling deformation generated in plates welded around hole. From the experiments, the severe distortion appeared in the weldments by the laser welding process, in which the specimen size plays an important role on the distortion but the hole configuration showed little effect. And the results of numerical analysis were corresponded well with the experiment ones. Thus, a thermal elasto-plastic analysis model for predicting the weld distortion of thin plate panel was successfully developed through this study.

• Steel and Composite Structures
• /
• 제12권5호
• /
• pp.395-412
• /
• 2012

The present work addresses the rotational capacity of steel-concrete composite beams, which is a key issue for the seismic design of composite frames. Several experimental tests from the literature are summarised, and the effects of various parameters on the available plastic rotation are discussed. Furthermore, a number of remarks are made regarding the need for supplementary experimental results. The authors carried out experimental tests on four composite beams in which the type, width and connection degree of the slab were varied. During the tests, the deflection and strains in the steel profiles and bars were measured and recorded, wherein the observed trends in the measured parameters indicated that the failure mode of the beam was influenced by global and local buckling. A comparison of the experimental results to the theoretical ultimate strengths and moment-curvature relationships confirms that buckling phenomena occurred after section yielding, even if a consistent plastic rotation developed. This rotational capacity is well evaluated by a formulation that is available in the literature.

• 한국자동차공학회논문집
• /
• 제10권2호
• /
• pp.212-219
• /
• 2002

In the frontal collision of cars, front parts of cars such as engine rail and side members that are composed of hatted section tubes should absorb most of the collision energy far the passenger compartment not to be deformed. For these reasons the study on the collapse characteristics, maximum crushing load and energy absorption capacity of hatted section tubes are needed. In this study, top hatted section tubes and double hatted section tubes are investigated. The maximum crushing load of hatted section tubes is induced from plastic buckling stress of plates by considering that the hatted section tubes are composed of plates with each different boundary conditions and that its material has a strain hardening effect. On this concept maximum crushing load equations of hatted section tubes are derived and verified by experiments. from the results of experiment, the differences of collapse characteristics between top hatted section tube and double hatted section tube are analysed. And mean crushing loads of hatted section tubes from experiments are compared with other theory.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 1997년도 춘계 학술발표회 논문집 Proceedings of EESK Conference-Fall 1997
• /
• pp.182-190
• /
• 1997

A new method to prevent reinforced concrete columns from brittle failure. The method is called transversely reinforcing method in which only the critical regions are confined in steel tube. The steel tubes can change the failure mode of the latter columns from the shear to the flexure. The steel tubes also increase the compressive strength, shear strength and deformation capacity of the infilled concrete. The following conclusions are reached on bases of the study on the seismic performance of the high-strength RC rectangualr short columns confined in steel tube with shear span tho depth ratio of 2.0 The brittle shear failure of high-strength reinforced concrete short columns with large amount of longitudinal bars, which cannot prevented by using the maximum amount of welded hoops, can be prevented by using the steel tube which confines all the maximum amount of welded hoops, can be prevented by using the steel tube which confines all the concrete inclusive of cover concrete. High-strength RC short columns confined in rectangular steel tube provided excellent enhancement of seismic performance but, found that plastic buckling of the steel tube in the hinge regions tended to occur when the columns were subjected to large cyclic lateral displacements. In order to prevent the plastic buckling when the columns lies on large on cyclic lateral displacements, the steel ribs were used for columns. Tests have established that the columns provide excellent enhancement of seismic performance of inadequately confined columns.

• Structural Engineering and Mechanics
• /
• 제57권5호
• /
• pp.785-808
• /
• 2016

An innovative Reduced Beam Section (RBS) connection, called Tubular Web RBS connection (TW-RBS), has been recently introduced and its performance has been numerically investigated in some earlier studies. The TW-RBS connection is a kind of accordion-web RBS connection in which part of the flat web of the beam is replaced by a steel tube at the expected region of the plastic hinge. This paper presents experimental results of three TW-RBS connections under cyclic loading. Obtained results indicated that TW-RBS reduces contribution of the beam web to the whole moment strength and creates a ductile fuse far from components of the beam-to-column connection. Besides, TW-RBS connection can increase story drift capacity up to 9% in the case of shallow beams which is much more than those stipulated by the current seismic codes. Based on the experimental results, the tubular web in the plastic hinge region improves lateral-torsional buckling stability of the beam such that only local buckling of the beam flange at the center of the reduced section was observed during the tests. In order to achieve a better understanding, behavior of all TW-RBS specimens are also numerically investigated and compared with those of experimental results.

• Structural Engineering and Mechanics
• /
• 제71권3호
• /
• pp.283-290
• /
• 2019

In global competition manufacturing companies have to produce modern, new constructions from advanced materials in order to increase competitiveness. The aim of my research was to develop a new composite cellular plate structure, which can be primarily used for structural elements of road, rail, water and air transport vehicles (e.g. vehicle bodies, ship floors). The new structure is novel and innovative, because all materials of the components of the newly developed structure are composites (laminated Carbon Fiber Reinforced Plastic (CFRP) deck plates with pultruded Glass Fiber Reinforced Plastic (GFRP) stiffeners), furthermore combines the characteristics of sandwich and cellular plate structures. The material of the structure is much more advantageous than traditional steel materials, due mainly to its low density, resulting in weight savings, causing lower fuel consumption and less environmental damage. In the study the optimal construction of a given geometry of a structural element of a road truck trailer body was defined by single- and multi-objective optimization (minimal cost and weight). During the single-objective optimization the Flexible Tolerance Optimization method, while during the multi-objective optimization the Particle Swarm Optimization method were used. Seven design constraints were considered: maximum deflection of the structure, buckling of the composite plates, buckling of the stiffeners, stress in the composite plates, stress in the stiffeners, eigenfrequency of the structure, size constraint for design variables. It was confirmed that the developed structure can be used principally as structural elements of transport vehicles and unit load devices (containers) and can be applied also in building construction.