• Steel and Composite Structures
• /
• v.49 no.4
• /
• pp.381-392
• /
• 2023

This study experimentally investigates the flexural behavior of steel-UHPC composite slabs composed of an innovative negative Poisson's ratio (NPR) steel plate and Ultra High Performance Concrete (UHPC) slab connected via demountable high-strength bolt shear connectors. Eight demountable composite slab specimens were fabricated and tested under traditional four-point bending method. The effects of loading histories (positive and negative bending moment), types of steel plate (NPR steel plate and Q355 steel plate) and spacings of high-strength bolts (150 mm, 200 mm and 250 mm) on the flexural behavior of demountable composite slab, including failure mode, load-deflection curve, interface relative slip, crack width and sectional strain distribution, were evaluated. The results revealed that under positive bending moment, the failure mode of composite slabs employing NPR steel plate was distinct from that with Q355 steel plate, which exhibited that part of high-strength bolts was cut off, part of pre-embedded padded extension nuts was pulled out, and UHPC collapsed due to instantaneous instability and etc. Besides, under the same spacing of high-strength bolts, NPR steel plate availably delayed and restrained the relative slip between steel plate and UHPC plate, thus significantly enhanced the cooperative deformation capacity, flexural stiffness and load capacity for composite slabs further. While under negative bending moment, NPR steel plate effectively improved the flexural capacity and deformation characteristics of composite slabs, but it has no obvious effect on the initial flexural stiffness of composite slabs. Meanwhile, the excellent crack-width control ability for UHPC endowed composite members with better durability. Furthermore, according to the sectional strain distribution analysis, due to the negative Poisson's ratio effect and high yield strength of NPR steel plate, the tensile strain between NPR steel plate and UHPC layer held strain compatibility during the whole loading process, and the magnitude of upward movement for sectional plastic neutral axis could be ignored with the increase of positive bending moment.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.3
• /
• pp.360-366
• /
• 2018

In shipyards hull forming is performed by the line heating method using a gas torch and by cold treatment using a roll-press. However, this forming process has some issues, such as difficulties in controlling and accurately estimating the amount of the heat input, as well as a harsh working environment due to exposure to loud noises and air pollution. The induction heating method, which is introduced in this paper, exhibits good control and allows for the estimation of precise heat input. Also, workers can carry out the induction heating in a comfortable working environment. In this research, the induction heating simulation, which consists of electro-magnetic, heat transfer and thermal elasto-plastic analysis, was developed and modified through induction heating experiments. Finally, the effective heating coil was designed for the automatic hull forming system based on the results of induction heating simulation. For the purposes of a future study, if an algorithm to obtain optimal working conditions is developed, automatic systems for hull forming can then be constructed.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2003.10a
• /
• pp.112-116
• /
• 2003

This paper describes the need for a ductile of Fiber Reinforced Plastic(FRP) reinforcement for concrete structures. The criteria to be met by the FRP, which are based on the properties of the steel rebar it is to replace, are threefold: high initial modulus, a definite yield point and a high level of ultimate strain. It is shown that the use of a fiber architecture based design methodology facilitates the optimization of the performance of FRP through material and geometric hybrid. Ductile hybrid FRP bars were successfully fabricated at 3mm and 5mm nominal diameters using an in-line braiding and pultrusion process.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1994.10a
• /
• pp.133-140
• /
• 1994

In this paper, we have proposed a new method to determine the initial billet for the forged products using a function approximation in neural networks. the architecture of neural network is a three-layer neural network and the back propagation algorithm is employed to train the network. By utilizing the ability of function approximation of neural network, an optimal billet is determined by applying nonlinear mathematical relationship between shape ratio in the initial billet and the final products. A volume of incomplete filling in the die is measured by the rigid-plastic finite element method. The neural network is trained with the initial billet shape ratio and that of the un-filled volume. After learning, the system is able to predict the filling region which are exactly the same or slightly different to results of finite element method. It is found that the prediction of the filling shape ratio region can be made successfully and the finite element method results are represented better by the neural network.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.9
• /
• pp.5474-5479
• /
• 2014

This study evaluated the residual stress and deformation for bracket castings of induction motors. Numerical analyses were performed to evaluate the residual stress distributions and displacements of bracket castings after the casting and final machining processes. Based on the analysis results, it was found that bracket casting was satisfied with the internal quality standards during the fabricating processes.

• Structural Engineering and Mechanics
• /
• v.12 no.1
• /
• pp.71-84
• /
• 2001

The objective of this paper is to develop a simplified method that could predict the strength of concrete filled steel tube (CFT) columns applicable to high strength material under combined axial compression and flexure. The simplified method for determining the strength of CFT columns is based on the interaction curve of the section approached by a polygonal connection of the points. These points are determined by using symmetrical properties of the CFT section. For each point, a simple equation is proposed to determine the strength of the slender columns under compression and flexure. The simple equation was adjusted with results of elasto-plastic analysis results. Validation of the simplified method is undertaken by comparison with data from the test conducted at Kyushu University. These results confirm the fact that the simplified method could accurately and reliably predict the strength of CFT columns under combined axial compression and flexure.

• Geomechanics and Engineering
• /
• v.16 no.2
• /
• pp.177-185
• /
• 2018

The subsidence mechanism of ground surface is a complex phenomenon when multiple seam coal mining operations are carried out. Particularly, the coal mining beneath karstic formations causes a very special form of subsidence. The subsidence causes elasto-plastic deformation of the karstic layers and the collapse of cavities leads to dolinization and/or sinkhole formation. In this study, a sinkhole with a depth of 90 m and a width of 25 m formed in Gelik district within the coal-basin of Zonguldak (NW, Turkey) induced by multiple seam coal mining operations in the past has been presented as a case-history together with two-dimensional numerical simulations and InSAR monitoring. The computational results proved that the sinkhole was formed as a result of severe yielding in the close vicinity of the faults in contact with karstic formation due to multiple seam longwall mining at different levels.

• Proceedings of the Korean Institute of Interior Design Conference
• /
• 2005.05a
• /
• pp.235-236
• /
• 2005

Recently the small medical clinics designed well are appearing even in the small and medium city. Especially in the rural area, these clinics have the role not only as medical facilities but also as community place for their fellowship. This project was launched by order of a female doctor, an otolaryngologist. Her order is focused on otolaryngology but I also proposed the design alternatives such as plastic surgery and dental surgery clinic designed under the same conditions. This project was also related with the classwork of interior architecture course of our faculty and I tried to let the students understand the relation between theory and practice. The design goal was to join together harmoniously two stories which were completely separated and I consistently concentrated on the expression of immateriality and superimposition of space.

• Steel and Composite Structures
• /
• v.13 no.6
• /
• pp.539-560
• /
• 2012

This study uses an explicit numerical algorithm to evaluate the ultimate load capacity analysis of a unit Strarch frame, accounting for the initial imperfection effects of the stress-erection process. Displacement-based filament beam element and an explicit dynamic relaxation method with kinetic damping are used to achieve the analysis. The section is composed of the finite number of filaments that can be conveniently modeled by various material models. Ramberg-Osgood and bilinear kinematic elastic plastic material models are formulated to analyze the nonlinear material behaviors of filaments. The numerical results obtained in the present study are compared with the results of experiment for stress-erection and buckling of unit Strarch frames.

• Geomechanics and Engineering
• /
• v.18 no.2
• /
• pp.121-131
• /
• 2019

This article discusses the phenomenon of plastic volumetric deformation of naturally structured clays before virgin yielding, i.e., subyielding behavior. A simple approach representing both the compression and shear responses of the clays during subyielding is demonstrated. A new compression model for structured clays based on the theoretical framework of the Structured Cam Clay (SCC) model via incorporation of the subyielding behavior is presented. Two stress surfaces are introduced to distinguish the subyielding and virgin yielding. The hardening and destructuring processes of structured clays under isotropic compression and shear are the focus of this work. The simulations of the compression and shear of eleven natural clays are studied for validation. The proposed work can accurately predict the subyielding behavior of structured clays both qualitatively and quantitatively and can be used for modeling structured clays under compression and shear responses in geological and geotechnical engineering problems.