• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.99-99
• /
• 1999

투명전도막인 Ito(Indium Tin Oxide)는 flat panel display 와 solar cell 같은 optoelectronic 이나 microelectronic device에서 널리 이용되어 지고 있다. 현재 상용화되고 있는 거의 대부분의 ITO 박막은 sputtering법에 의해 제조되고 있으나 공정상의 이유로 15$0^{\circ}C$이상의 기판온도가 요구되어진다. 그런, 실제 display device 제조공정에서는 비정질 실리콘 박막이나 유기막 위에 ITO박막을 제작할 필요성이 증대되어 지고 있고, 또한 다른 전자소자에 있어서도 상온 ITO 박막 형성 공정에 대한 필요성이 증대되고 있다. 이러한 이유로 본 실험에서는 IBAE(Ion Beam Assisted Evsporation)을 이용하여 저온 ITO박막을 유기막 위에 증착하는 공정에 대한 연구를 수행하였다. 이렇게 증착된 ITO 박막의 결정성은 비정질이었다. 또한, 모든 display device 제작에는 식각공정이 필수인데 기존에 사용되고 있는 wet etching 법은 등방성 식각특성 때문에 미세 pattern 형성에 부적합？, 따라서 비등방성 식각에 용이한 plasma etching법을 사용하여 저온 증착된 ITO 박막의 식각특성을 알아보았다. 실험에 사용된 식각장비는 자장 강화된 유도결합형 플라즈마 식각장비(MEICP)를 사용하였으며, 13.56MHz의 RF power를 사용하였다. 식각조건으로 source power는 600W~1000W, 기판 bias boltage는 -100V~-250V를 가하였으며, Ar, CH4, O2, H2, BCl3의 식각 gases, 5mTorr~30mTorr의 working pressure 변화 그리고 기판 온도에 따른 식각특성을 관찰하였다. ITO 가 증착된 기판으로는 유기물 중 투명전도성 박막에 기판으로서 사용가능성이 클 것으로 기대되어지는 PET(polyethylene-terephtalate), PC(polycarbonate), 아크릴을 사용하여 기판 변화가 식각특성에 미치는 영향에 대해서 각각 관찰하였다. 식각속도의 측정은 stylus profiler를 이용하여 측정하였으며 식각후에 표면상태는 scanning electron spectroscopy(SEM)을 이용하여 관찰하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.59-59
• /
• 1999

DLC(diamond-like carbon)필름은 다이아몬드와 유사한 강도, 낮은 마차계수, 높은 Optical band gap, NEA(negative electron affinity)등의 우수한 특성을 가지고 있어, 내마모 코팅이나 정보저장 매체의 윤활 코팅, FED(field emission display)의 전계방출소자등 다양한 분야에의 응용이 연구되고 있다. DLC 필름은 PECVD(plasma enhanced chemical vapor deposition), IBAD(ion beam assisted deposition), Laser ablation, Cathodic vacuum arc등의 process를 이용하여 증착되고 있다. 특히 이러한 필름의 물성은 입사되는 이온의 에너지에 의해 좌우되는데, Lifshitz 등의 연구에 의하여 hyperthermal species를 이용한 DLC 필름의 성장은 초기에 subsurface로의 shallow implantation이 일어난 후 높은 sp3 fraction을 갖는 필름이 연속적으로 성장한다는 subplantation model이 제시 되었다. 본 연구에서는 기판과 subplantation 영역이 이후 계속하여 증착되는 순수 DLC 필름의 특성 변호에 미치는 영향에 대하여 관심을 가지고 실험을 행하였다. 본 실험에서는 상기 제시되어 있는 방법보다도 더욱 정확하고도 독립적으로 탄소 음이온의 에너지와 flux를 조절할 수 있는 Cs+ ion beam sputtering system을 이용하여 탄소 음이온의 에너지를 40eV에서 200eV까지 변화시키며 필름을 증착하였다. Si(100) 웨이퍼를 기판으로 사용하였고 증착 압력은 5$\times$10-7torr 였으며 인위적인 기판의 가열은 하지 않았다. 또한 Ion beam deposited DLC film의 growth process를 연구하기 위하여 200eV의 탄소 음이온을 시간(증착두께)을 변수로 하여 증착하였고, 이 때에는 Kaufman type의 gas ion beam을 이용하여 500eV의 Ar+ ion으로 pre-sputering을 행하였다. 탄소 음이온의 에너지와 증착두께에 따라 증착된 film 내의 sp3/sp2 ratio 의 변화를 XPS plasmon loss 와 Raman spectra를 이용하여 분석하였다. 또한 증착두께에 따른 interlayer의 결합상태를 관찰하기 위하여 AES와 XPS 분석을 보조로 행하였다.

• Tribology and Lubricants
• /
• v.11 no.5
• /
• pp.59-65
• /
• 1995

Tribological behaviors of nitrogen incorporated amorphous diamond-like carbon films were experimentally measured under a vacuum ($3 \times 10^{-5}$ Torr) using a ball (AISI 52100 steel)-on-disk wear-rig. Nitrogen incorporated DLC films were deposited by r.f. plasma assisted chemical vapor deposition method. Mixtures of benzene and ammonia or nitrogen gases were used as the reaction gases for the r.f. PACVD, and Si (100) wafer was used as the substrate. In the tribo-test, effects of DLC film thickness and normal load in friction were measured and discussed. Results showed that friction of nitrogen incorporated DLC films from a mixture gas of benzene and ammonia was lower than that of 100% benzene, specially in the measurement of minimum coefficient of friction. Differences in frictional characteristics of nitrogen incorporated DLC films were explained with the changes in chemical structures of the films. Result also showed that friction of DLC films increased with the sliding contact cycle, which remarkably accompanied with roll-shaped wear debris. Mechanisms and roles of the polymer-like wear debris were presented and discussed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.95-95
• /
• 2012

스터퍼링 기술이 1852년 Grove에 의해서 최초 발견되어 1979년 Chapin에 의해서 planar magnetron cathode 개발로 진공코팅기술의 새로운 영역을 열게 되어 현재까지 디스플레이, 반도체, 태양전지, 광학산업 및 전자부품 등 나노 산업에 필수적으로 적용되고 있다. 스퍼터링 입자는 운동량 전달에 의한 것으로 운동량을 갖는 나노 스퍼터링 입자는 기판에 대한 박막의 부착력이 우수하고 대면적에 균일하고 재현성 있게 성막되는 특징을 갖고 있다. 마그네트론 스퍼터링 기술이 산업에 응용되면서 주로 4분야에서 많은 연구, 개발이 되어져 왔다. 첫째는 타겟의 고순도 및 고밀도화와 더불어 가격이 고가로 됨에 따라 타겟 사용효율의 향상이다. 플라즈마를 발생시키는 캐소드의 자기회로를 1차원, 2차원 및 회전운동을 통해서 사용효율을 향상시키고 있다. 둘째는 기판에 대해서 박막특성이 균일하도록 코팅하는 것이다. 디스플레이에서는 글래스 기판이 대면적으로 됨에 따라서 핸들링이 어려워져 여러 개의 캐소드 자기회로를 선형적으로 이동시켜 박막두께분포를 최적화하며 반응성 가스를 사용해서 균일한 특성의 박막을 제작하는 경우에는 가스분사관과 배기펌프계의 기하학적 위치 및 가스 유동학적 해석이 필요하다. 셋째는 스퍼터링 입자의 이온화로 의한 박막의 특성향상과 반도체 trench의 높은 aspect ratio hole을 채우는 것이다. 이온화 방법으로는 inductively coupled plasma (ICP), microwave amplified (MA), high power impulse (HIPI), hollow cathode magnetron (HCM), self-sustained sputtering 등이 사용되어져 왔으며 최근에는(neutral beam-assisted sputtering (NBAS)에 의한 박막특성향상 방법이 발표되고 있다. 넷째는 플라즈마 및 박막두께 시뮬레이션에 대해서 많은 발표가 되고 있다. 본 발표에서는 상기의 4 분야를 포함한 향후 개발방향에 대해서 소개할 예정이다.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.11
• /
• pp.3362-3366
• /
• 2013

A simple and quick separation technique for selenite in natural water was developed using $TiO_2$@$SiO_2/Fe_3O_4$ nanoparticles. For the synthesis of nanoparticles, a polymer-assisted sol-gel method using hydroxypropyl cellulose (HPC) was developed to control particle dispersion in the synthetic procedure. In addition, titanium butoxide (TBT) precursor, instead of the typical titanium tetra isopropoxide, was used for the formation of the $TiO_2$ shell. The synthesized nanoparticles were used to separate selenite ($Se^{4+}$) in the presence of $Se^{6+}$ or selenium anions for the photocatalytic reduction to $Se^0$ atom on the $TiO_2$ shell, followed by magnetic separation using $Fe_3O_4$ nanoparticles. The reduction efficiency of the photocatalytic reaction was 81.4% at a UV power of 6W for 3 h with a dark adsorption of 17.5% to the nanoparticles, as determined by inductively coupled plasma-mass spectrometry (ICP-MS). The developed separation method can be used for the speciation and preconcentration of selenium cations in environmental and biological analysis.

• Corrosion Science and Technology
• /
• v.6 no.1
• /
• pp.18-23
• /
• 2007

DLC coatings have been deposited onto substrate of STS 316L and Ti alloy using r.f. PACVD (plasma-assisted chemical vapor deposition) with a mixture of $C_{6}H_{6}$ and $SiH_{4}$ as the process gases. Corrosion performance of DLC coatings was investigated by electrochemical techniques (potentiodynamic polarization test and electrochemical impedance spectroscopy) and surface analysis (scanning electron microscopy). The electrolyte used in this test was a 0.89% NaCl solution of pH 7.4 at temperature $37^{\circ}C$. The porosity and protective efficiency of DLC coatings were obtained using potentiodynamic polarization test. Moreover, the delamination area and volume fraction of water uptake of DLC coatings as a function of immersion time were calculated using electrochemical impedance spectroscopy. This study provides the reliable and quantitative data for assessment of the effect of substrate on corrosion performance of Si-DLC coatings. The results showed that Si-DLC coating on Ti alloy could improve corrosion resistance more than that on STS 316L in the simulated body fluid environment. This could be attributed to the formation of a dense and low-porosity coating, which impedes the penetration of water and ions.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.6
• /
• pp.119-126
• /
• 2014

Micro-holes of conductive ceramic are required in micro structures. Micro-electrical discharge machining (Micro-EDM) is an effective machining method since EDM is as process for shaping hard metals and complex-shaped holes by spark erosion in all kinds of electro-conductive materials. However, as the depth of micro hole increases, the machining condition becomes more unstable due to inefficient removal of debris between the electrode and the workpiece. In this paper, micro-EDM was performed to evaluate machining characteristic such as electrode wear, machining time, taper angle, radial clearance with varying voltage and ultrasonic vibration on 10 vol.% Carbon-nanotube reinforced conductive $Al_2O_3$ composite fabricated by spark plasma sintering in previous research.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2002.11a
• /
• pp.14-19
• /
• 2002

In this study, as Cu diffusion barrier, tantalum nitrides were successfully deposited on Si(100) substrate and SiO2 by plasma assisted atomic layer deposition(PAALD) and thermal ALD, using pentakis (ethylmethlyamino) tantalum (PEMAT) and $NH_3$ as precursors. The TaN films were deposited on $250^{\circ}$C by both method. The growth rates of TaN films were $0.8{\AA}$/cycle for PAALD and $0.75{\AA}$/cycle for thermal ALD. TaN films by PAALD showed good surface morphology and excellent step coverage for the trench with an aspect ratio of h/w - $1.8 : 0.12 \mu\textrm{m}$ but TaN films by thermal ALD showed bad step coverage for the same trench. The density for PAALD TaN was $11g/\textrm{cm}^3$ and one for thermal ALD TaN was $8.3g/\textrm{cm}^3$. TaN films had 3 atomic % carbon impurity and 4 atomic % oxygen impurity for PAALD and 12 atomic % carbon impurity and 9 atomic % oxygen impurity for thermal ALD. The barrier failure for Cu(200nm)/TaN(l0nm)/$SiO_2(85nm)$/Si structure was shown at temperature above $700^{\circ}$C by XRD, Cu etch pit analysis.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.12
• /
• pp.3950-3956
• /
• 2012

In order to improve the bioactivity and mechanical properties of hydroxyapatite (HAp), chitosan (Chi) was in situ combined into HAp to fabricate a composite scaffold by a sublimation-assisted compression method. A highly porous film with sufficient mechanical strength was prepared and the bioactivity was investigated by examining the apatite formed on the scaffolds incubated in simulated body fluid. In addition, the cytotoxicity of the HAp/Chi composite was studied by evaluating the viability of murine fibroblasts (L-929 cells) exposed to diluted extracts of the composite films. The apatite layer was assessed using scanning electronic microscopy, inductively coupled plasma-optical emission spectrometry and weight measurement. Composite analysis showed that a layer of micro-sized, needle-like crystals was formed on the surface of the composite film. Additionally, the WST-8 assay after L-929 cells were exposed to diluted extracts of the composite indicated that the HAp/Chi scaffold has good in vitro cytocompatibility. The results indicated that HAp/Chi composites with porous structure are promising scaffolding materials for bone-patch engineering because their porous morphology can provide an environment conductive to attachment and growth of osteoblasts and osteogenic cells.

• Journal of the Korean Ceramic Society
• /
• v.37 no.1
• /
• pp.96-101
• /
• 2000

Comparative studies on microstructure, and mechanical and anti-oxidation properties between TiN and Ti-Si-N films were performed. The Ti-Si-N films were deposited on high-speed steel and silicon wafer substrates by plasma-assisted chemcial vapor deposition(PACVD) technique. The Si addition to TiN film caused to change the microstructure such as grain size refinement, randomly multi-oriented microstructure, and nano-sized codeposition of silicon nitride in the TiN matrix. The Ti-Si-N film, contains Si content of ∼7 at.%, showed the micro-hardness value of ∼3400 HK, which was higher than the pure TiN film whose hardness was ∼1500HK. The Ti-Si(7 at.%)-N film also showed much improved anti-oxidation properties compared with those of the pure TiN film. These properties were also related to the microstructure of Ti-Si(7 at.%)-N film was formed and retarded further oxidation of the nitridelayer. These properties were also related to the microstructure of Ti-Si(7 at.%)-N film which was characterized by nano-sized precipitates of silicon nitride phase in the TiN matrix and randomly oriented grains.