• Journal of the Korean Home Economics Association
• /
• v.25 no.1
• /
• pp.11-18
• /
• 1987

The purpose of this study was to investigate the crease recovery and the elastic recovery as a function of the direction of plain woven fabrics. The crease recovery was measured by Mosanto's Method and the elastic recovery was investigated by Autograph for ten kinds of plain woven fabric samples. The results were as follows; 1. Values of crease recovery were in the order of bias>weft>warp. 2. The lengthening of recovery time had a little effect on crease recovery. 3. The directions of crease recovery were affected by that of thread twist. 4. The linearity was shown between total crease recovery and warp-weft crease recovery. 5. The linearity was found between crease recovery and elastic recovery in the fabrics.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.22 no.10
• /
• pp.704-709
• /
• 2010

The effect of oil on flow boiling of R-123 in a plain tube bundles was experimentally investigated for a range of quality and heat flux. It is shown that the heat transfer coefficient decreased as the oil concentration increased. Comparison with the previous pool boiling data reveals that the reduction of heat transfer coefficient by oil is more pronounced in pool boiling, and the difference increased with the increase of oil concentration and heat flux. Within the experimental range, the variation of mass flux or quality has negligible effect on the heat transfer coefficient.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.17 no.2
• /
• pp.61-67
• /
• 2009

In the present study, an experiment was conducted to investigate the heat and mass transfer performance of heat exchangers used in the condensing gas boiler. Two types of spiral circular fin-tube heat exchangers and a plain tube were tested in the flue gas of propane and dry air. Heat and mass transfer coefficients were measured and compared with the previous correlations. The experimental data for the sensible heat transfer of the plain tube reasonably agreed with the previous correlations for dry air and flue gas. However, the mass transfer coefficient of the plain tube was greater than the previous correlations. The pH, $NO_x$, and $SO_x$ data of condensate were provided.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.05b
• /
• pp.393-396
• /
• 2005

This paper presents the results of drying shrinkage of concrete using shrinkage-reducingadmixture(DSRA) studied by the authors through mock-up test. DSRA is proportioned by expansive admixture and shrinkage reducing agent(SRA). Flowing concrete method is also applied to assist the concrete to reduce drying shrinkage by decreasing water content at the same time. The use of EA and SRA does not affect fluidity, bleeding and setting time. Compressive strength of concrete using EA along with SRA exhibited less than that of plain concrete. However, The compressive strength with combination of EA-SRA along with flowing concrete method shows comparable to that of plain concrete. The application of developed method can contribute to reducing drying shrinkage by as much as 30-40$\%$ compared with that of plain concrete.

• Tuberculosis and Respiratory Diseases
• /
• v.40 no.4
• /
• pp.353-356
• /
• 1993

Advent of new imaging modalities such as computed tomography, magnetic resonance imaging and ultrasound contributed greately to the specific imaging diagnosis. However plain chest X-ray is still most prequently used for imaging diagnosis of respiratory disease in clinical pratic and it is important to make a good quality of X-ray film and good interpretation. The optimal chest X-ray should be taken with full inspiration without rotation and motion and the exposure is at the level of barely demonstrable thoracic vertebral disc space. It is recommended that higk KVP technique for detection of lesions which is overlaped by mediastinum, heart and rib cage. It is better to examine chest X-ray film start at some distance(6-8 feet) and closer to the film later on and the reader should not read a film in fatigue condition. The reading room should be quiet and relately dark illumination. It is important, to make a good X-ray film and good interpretation to reduce the observer error.

• Structural Engineering and Mechanics
• /
• v.57 no.2
• /
• pp.265-280
• /
• 2016

A NLFE model was proposed to investigate the mechanical behavior of short columns, cast using plain or fibrous lightweight aggregate concrete (LWAC), and subjected to elevated temperatures of up to $700^{\circ}C$. The model was validated, before its predictions were extended to study the effect of other variables, not studied experimentally. The three-dimensional NLFE model was developed using ANSYS software and involved rational simulation of thermal mechanical behavior of plain and fibrous LWAC as well as longitudinal and lateral steel reinforcement. The prediction from the NLFE model of columns' mechanical behavior, as represented by the stress-strain diagram and its characteristics, compared well with the experimental results. The predictions of the proposed models, considering wide range of lateral reinforcement ratios, confirmed the behaviors observed experimentally and stipulated the importance of steel confinement in preserving post-heating mechanical properties of plain and fibrous LWAC columns, being subjected to high temperature.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.13 no.3
• /
• pp.128-137
• /
• 2005

In this study, dry and wet surface pressure drop and heat transfer characteristics of heat exchangers having plain fins were investigated. Nine samples having different fin pitches and rows were tested. The wet surface heat transfer coefficient was reduced from experimental data using enthalpy-potential method. The wet surface heat transfer coefficients were approximately equal to the dry surface values except for one row configuration. For one row configuration, the wet surface heat transfer coefficients were approximately $30\%$ lower than the dry surface values. For the pressure drop, the wet surface yielded approximately $30\%$ higher values compared with the dry surface counterpart. Data were compared with existing correlations.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2000.09a
• /
• pp.413-420
• /
• 2000

Cheju Island has nature of typical trass through volcanic activities in many times. The soil in Cheju Island has principally sprung from basalt and partially made up of trachyte, trachyte's nature and site. Also ancient relics, plain coarse pottery's kilns and pantiles kilns are homogeneously distributed all over the Cheju Island. In this study, as a result of X-ray fluorescence spectrometer and Mossbauer spectroscopy of a sample are from plain coarse pottery and pantiles in 5 regions of Cheju Island. It is thought that these samples are partially formed from neutral volcanic rock like trachyte and Atomicity state of iron is almost Fe$\^$3+/. Also the magnetic hyperfine field length of goethite, contained these samples is less than synthetic goethite magnetic hyperfine field length and this result shows that disintegration of inner magnetic order, created by partial substitution of diamagnetic positive ion containing Fe$\^$3+/ and Al$\^$3+/ in goethite lattice.

• Proceedings of the KIEE Conference
• /
• 1999.07g
• /
• pp.3004-3006
• /
• 1999

In this paper, we present the ball position and path plain method for the robot-soccer using optical flow. As we compare a optical flow method with a general method within the accurate and effective ball position information of robot-soccer or the path planning, we prove accurate and effective optical flow algorithm to apply ball position and path plain for robot-soccer

• Journal of the Korean Society of Safety
• /
• v.19 no.1
• /
• pp.31-37
• /
• 2004

The mechanical strength and crack propagation of plain woven carbon fiber fabric laminate composites are examined by acoustic emission(AE). AE signals are measured during the tensile test and fracture tests. Thus, the relationship between AE signal and load-displacement curves and crack extension length are shown. Also the fracture mechanisms in terms of AE characteristics are discussed in viewpoint of crack propagation behavior.