• 대한기계학회논문집A
• /
• 제25권11호
• /
• pp.1720-1729
• /
• 2001

Wear characteristics of Nylon and acetal pinions against steel gears for different pitch line velocities was studied with a power circulating gear test rig under unlubricated condition. Specific wear rate was measured as a function of tooth number, module, tooth width and total revolution. The worn tooth surfaces were examined with a profile projector. The Nylon pinion showed lower specific wear rate than the acetal pinion. However, the Nylon pinion was fractured at high tooth loads, whereas the acetal pinion exhibited a steady wear behavior. The wear characteristics of Nylon pinion varied significantly with the Pitch line velocity. Wear occurred most severely at the tooth tip and the region immediately below the pitch line of pinion. The dominant wear mechanisms were adhesion and abrasion.

• 한국음향학회:학술대회논문집
• /
• 한국음향학회 1994년도 FIFTH WESTERN PACIFIC REGIONAL ACOUSTICS CONFERENCE SEOUL KOREA
• /
• pp.963-970
• /
• 1994

In speech signal processing, it is very important to detect the pitch exactly. The algorithms for pitch extraction that have been proposed until now are not enough to detect the fine pitch in speech signal. Thus we propose the new algorithm which takes advantage of the G-peak extraction. It is the method to find MZCI(maximum zer-crossing interval) which is defined as cut-off bandwidth rate of LPF (low pass filter)and detect the pitch period of the voiced signals. This algorithm performs robustly with a gross error rate of 3.63% even in 0 dB SNR environment. The gross error rate for clean speech is only 0.18%. Also it is able to process all course with speed.

• 말소리와 음성과학
• /
• 제8권4호
• /
• pp.131-138
• /
• 2016

This study analyzes the characteristics of good impression using speech manipulation scripts and investigates the characteristics of preferred speech voice. Fourty male and female college students participated in this study. They have been exposed to the Gyeongsang dialect spoken by their friends and family for more than 15 years. Two sample voices(1 male and 1 female), considered as giving good impression, were subject to voice analysis. Two students were asked to read the sample paragraph of 'Walking' and their voice samples were analyzed through Praat. The collected speech data were manipulated into 4 different sets by changing pitch level, degree of loudness and speech rate. First, both men and women received good impression more from pitch-lowered sound than from the original one. Second, men tended to receive good impression more from slightly louder voice than from the natural-pitched one. Third, it was shown that men often felt more drowned to a voice at slightly faster speech rate than at the original speech rate. Overall, both male and female listeners favored lower pitch over the original pitch. Men tended to prefer louder voice sound while women preferred less loud one. Men received better impression at a lower speech rate but women at a faster speech rate.

• 한국음향학회지
• /
• 제13권5호
• /
• pp.77-82
• /
• 1994

음성신호 처리에서, 피치를 정확하게 찾아내는 것이 매우 중요하다. 현재까지 많은 피치 검출 방법들이 제안되어 왔지만, 광범위한 화자와 다양한 음성 데이터로부터 정확한 피치를 찾는 것은 어렵다. 따라서 본 논문에서는 G-peak 검출을 이용한 새로운 피치 검출 알고리즘을 제안한다. 이 방법은 G-peak 의 MZCI (최대 영교차 간격) 을 LPF (low-pass filter)의 차단대역폭으로 결정하여 음성신호의 피치를 검출하는 방법이다. 본 알고리즘은 0dB SNR 환경 하에서 3.36%의 그로스 에러를 나타내는 잡음에 강인한 방법이다. 또한 잡음이 없는 음성의 그로스 에러는 0.18%였고, 모든 과정은 고속 처리가 가능하다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.296-296
• /
• 2012

LCD panel 검사를 위한 Probe unit은 대형 TV 및 모바일용 스마트폰을 중심으로 각광을 받고 있는 소모성 부품으로 최근 pitch의 미세패턴화가 급속히 진행되고 있다. 본 연구에서는 Slit Wafer 제작 공정을 최적화하기 위해 25 um pitch의 마스크를 설계, 제작하였다. 단공과 장공을 staggered 형태로 배열하여 25 um/25 um line/space pitch로 설계하였다. 또한 단위실험을 위해 직접 25 um pitch로 설계하여, 동일한 실험조건을 적용하여 최적 조건을 찾고자 하였다. 반응변수는 Etch rate 및 profile angle로 결정하였으며, 약 200~400 um 에칭된 slit의 상단과 하단의 폭, 그리고 식각깊이를 SEM 측정사진을 통해 정한 후 etch rate 및 profile angle을 결정하였다. 인자는 식각속도 및 wall의 각도를 결정하는 식각 및 passivation 가스의 유량, chamber 압력(etching/passivation), 식각시간 등으로 정하였으며, 이들의 최대값과 최소값 2 수준으로 실험계획을 설계하였다. 식각 조건에 따라 8회의 실험을 수행하였다. 가스의 유량은 SF6 400 sccm, C4F8 400 sccm, 식각 싸이클 시간은 5.2~10.4 sec, passivation 싸이클시간 4 sec로 하였으며, 압력은 식각시 7.5 Pa, passivation 시 10 Pa로 할 경우가 가장 sharp하게 나타났다. Coil power 와 platen power는 각각 2.6 KW, 0.14 KW로 하였으며, 최적화를 위한 인자의 값들은 이 범위에서 조절하였다. 이러한 인자의 조건 조절을 통해 etch rate는 5.6 um/min~6.4 um/min, $88.9{\sim}89.1^{\circ}$의 profile angle을 얻을 수 있었다.

• 한국지능시스템학회논문지
• /
• 제24권4호
• /
• pp.366-371
• /
• 2014

본 논문에서는 정격풍속 이상에서 발전량을 일정하게 유지하기 위하여 회전속도의 변화율을 이용한 신경망 피치제어기가 제안되었다. 제안된 신경망 피치제어기는 발전기의 정격 회전속도와 현재 회전속도의 차이를 기본정보로 사용하고 추가적으로 발전기 회전속도의 변화율을 사용하였다. 시뮬레이션은 Matlab/simulink에서 수행되었으며, 시뮬레이션을 통해 제안된 피치제어기를 사용한 풍력발전기는 발전기의 정격 회전속도인 122.9[rad/s]로 잘 유지 되는 것을 확인하였다.

• 설비공학논문집
• /
• 제17권3호
• /
• pp.268-276
• /
• 2005

The aim of this paper is to suggest one efficient method for the various requirements of performance during the process designing and producing an impeller. The study considers that the revisions of a pitch angle of an impeller at an axial turbo fan affect an air flow rates and a static pressure rise. The axial turbo fan specified with the 250 Pa maximum static pressure and 1300 CMH fan air flow rates was tested and analyzed by CFD. The Numerical results show that the air flow rates are calculated to 1,175 CMH, 1,223 CMH, 1,270 CMH, 1,340 CMH and 800 CMH in cases that the pitch angles are $44^{\circ},\;49^{\circ},\;54^{\circ},\;59^{\circ},\;and\;64^{\circ}$ respectively. Also the static pressure rises are shown to 108 Pa, 122Pa, 141 Pa, 188 Pa and 63 Pa at the same cases. The air flow rate is increased linearly according to the changes of the pitch angle from $44^{\circ}\;to\;59^{\circ}$ and the maximum air flow rate passing the impeller is increased to $13\%$ over at the case of $59^{\circ}$ pitch angle compared with the reference case of $54^{\circ}$ pitch angle. The static pressure rise is increased linearly according to the changes of the pitch angle from $44^{\circ}\;to\;54^{\circ}$, too. The static pressure rise at the $59^{\circ}$ pitch angle is increased to $33\%$ over compared with the $54^{\circ}$ pitch angle. The result shows that the revisions of pitch angle make the static pressure rise increase widely. However the air flow rates and the static pressure rise at the $64^{\circ}$ pitch angle are suddenly decreased because of over-changed pitch angle.

• 한국군사과학기술학회지
• /
• 제14권6호
• /
• pp.1026-1030
• /
• 2011

This paper presented here contains development of variable stability system(VSS) control laws for the KIFS (Korean In-Flight Simulator) aircraft to simulate the dynamics of F-16 aircraft. Development of VSS Control law for pitch rate, roll rate, yaw rate simulation for three specified flight conditions using Model Following Technique with rate feedback autopilot for stability provision. The direct lift force controller was also added to the developed VSS control law to simulate the pitch rate and normal g-load simultaneously. The simulation results show high accuracy of F-16 aircraft's pitch, roll, yaw rate and g-load simulation.

• International Journal of Automotive Technology
• /
• 제8권6호
• /
• pp.753-760
• /
• 2007

In this paper, a roll and pitch estimation algorithm using a set of accelerometers and wireless sensor networks(S/N) is presented for use in a passenger vehicle. While an inertial measurement unit(IMU) is generally used for roll/pitch estimation, performance may be degraded in the presence of longitudinal acceleration and yaw motion. To compensate for this performance degradation, a new roll and pitch estimation algorithm is proposed that uses an accelerometer array, global positioning system(GPS) and in-vehicle networks to get information from yaw rate and roll rate sensors. Angular acceleration and roll and pitch approximation are first calculated based on vehicle kinematics. A discrete Kalman filter is then applied to estimate both roll and pitch more precisely by reducing noise from the running engine and from road disturbance. Finally, the feasibility of the proposed algorithm is shown by comparing its performance experimentally with that of an IMU in the framework of an indoor test platform as well as a test vehicle.

• 한국세라믹학회지
• /
• 제35권9호
• /
• pp.974-980
• /
• 1998

This study is concerned with the production of carbon fiber reinforced carbon(C/C) with polyaromatic mesophase pitch as matrix precursor and with the investigation of friction-wear characteristics in ambient air using a constant speed type of friction tester. The main problem in using the polyaromatic mesophase as the matrix precursor is the high viscosity which may limit the complete impregnation of the fiber preform in the vacuum. To solve these problems two dimensional carbon fiber fabrics were infiltrated with meso-phase pitch in the pitch impregnator. After the impregnation and the heat treatment process. C/C com-posites were characterized by density porosity to monitor the influence of high pressure and temperature. It showed that the bulk density was increased and the apparent porosity and the density increasing rate was reduced as repeating the impregnation the carbonization and the heat treatment. The friction-wear charac-teristics of C/C composites were investigated by measuring the average friction coefficient and the specific wear rate as functions friction speed and friction pressure using a constant speed type of friction tester. C/C composite4s showed the average friction coefficient to be reduced as increasing the friction speed and the friction pressure.