• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.985-990
• /
• 1995

Recently, the development of high speed and high precision NC-lathe for piston head machining is needed for the complexity and diversity of the piston head shape used in automobile reciprocating engine. THe piston head has many complex shapes in the aspect of fuel economy, such as ovality, profile, double ovality and recess. Among them, for the maching of the over shape of 0.1~1mm the cutting tool should move periodically symchronized with the rotation of piston workpiece. The cutting tool feeed system must have high positioning accuracy for the precise machining, high speed for the fast maching and high dynamic stiffness for the cutting force. The linear brushless DC motor is used for satisfying these coditions. The ballbush guide and supporting guide using turcite is used for the guidance of the feed drive system. Linear encoder, digital servo ampllifer and controller are used for driving the motor. THis paper presents the design and simulation of the new tool feed system for noncircular machining.

• Tribology and Lubricants
• /
• v.13 no.2
• /
• pp.89-95
• /
• 1997

This paper considers two dimensional analysis for lubrication between the single piston ring and the cylinder liner. The piston ring is treated as a reciprocating, hydrodynamic bearing with combined sliding and squeeze motion. Reynolds' equation is used, to model lubrication with Reynolds' cavitation boundary condition. This analysis is developed to get the cyclic variation of minimum film thickness and viscous frictional force. Two types of piston ring face shape are considered. This result can be used to study the influence of ring shape design parameter to improve the characteristics of sealing and lubrication.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.21 no.3
• /
• pp.255-263
• /
• 2018

This paper investigated design requirements for piston pumps, which were used as the power source of light rescue vehicle, and designed a piston pump satisfying such requirements. In order to satisfy the driving specification of the rescue device, the pump needs to be designed using the displacement volume of 110 cc/rev, the pressure of 350 bar and the rotation speed of 2,200 rev/min. The design was verified by flow and structural analyses respectively. The shape of the piston pump was optimized in terms of both flow characteristics and structural stability. A test equipment was also fabricated to verify the developed piston pump and test conditions were established. Finally, the developed piston pump was tested for its performance and operating temperature.

• 유체기계공업학회:학술대회논문집
• /
• 2005.12a
• /
• pp.448-453
• /
• 2005

Temperature Control Valve (TCV) is one of the useful temperature control devices, which is used to control constant temperature of working fluid in power and chemical plants and domestic water supply systems. TCV is composed of body, cylinder and piston, and the body shape has a symmetrical H-type. In general, it has several inlet and outlet holes, and its shape is like as tubular sleeve. The piston has three rings two rings of the end of piston have the function of controlling inlet flow rate with hot and cold working fluids, the center ring has the function of preventing hot and cold water from intermixing. Consequently, the shapes of piston and cylinder are the main design parameters in the performance of TCV. In this study, numerical analyses were carried out with two different piston and cylinder shapes to investigate the functions as a temperature control valve and the flow characteristics according to piston opening grade in TCV. Using a commercial code, FLUENT, velocity and pressure fields in TCV are obtained under steady, standard $k -{\epsilon}$ turbulence model and no-slip condition.

• Transactions of Materials Processing
• /
• v.26 no.1
• /
• pp.28-34
• /
• 2017

Multi-pass shape rolling is performed to produce long products of arbitrary cross-sectional shapes. In the past, the multi-pass shape rolling process has been designed by the trial and error method or the experience of experts based on the empirical approach. Particularly, the design of roll caliber in shape rolling is important to improve product quality and dimensional accuracy. In this paper, the caliber design and pass schedule of multi-pass shape rolling were proposed for manufacturing piston ring wire. In order to design roll caliber, major shape parameter and dimension was determined by analysis of various caliber design. FE-simulation was conducted to verify effectiveness of proposed process design. At first, forming simulation was performed to predict shape of the product. Then, fracture of the wire was evaluated by critical damage value using normalized Cockcroft-Latham criteria. The experiment was carried out and the results are within the allowable tolerance.

• Tribology and Lubricants
• /
• v.31 no.5
• /
• pp.221-228
• /
• 2015

It is possible to prevent a piston from contacting the cylinder by changing the shape of the piston or by applying micro-textures, such as micro-grooves or micro-holes, over the piston surface. Usually, the minimum radial clearance reaches its minimum value at the beginning of the suction stroke because the pressure around the piston is low and almost axisymmetric such that the net pressure force on the piston is not sufficiently high to support the piston from touching the cylinder. In this study, we apply a series of saw-tooth-shaped grooves on the piston surface, and numerically investigate the effects of groove depth, groove angle, and the number of grooves with radial clearance variations using a finite difference method. We conduct a dynamic analysis of the piston for various changes in groove geometries to obtain the minimum radial clearance variation for the entire compression cycle. The minimum radial clearance increases while friction loss decreases when we apply the series of saw-tooth-shaped grooves on the piston. In addition, we analyze the impact of the change in the groove shape variable due to changes in radial clearance. Leakage variations are relevant to radial clearance, but have almost no effect on the groove parameters.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.24 no.2
• /
• pp.244-250
• /
• 2015

We propose a simulation technique to estimate the reduction effect of the pressure/flow pulsation by analysis of the pulsation variables and notch shape of the valve plate of a swash-plate-type variable piston pump. First, using SimulationX$^{(R)}$, we perform a theoretical kinematic analysis according to the variable swash-plate angle and rotational velocity in order to design a single-piston pump. In designing the notch shape of the valve plate of the swash-plate-type variable piston pump as one of the pulsation variables, we investigate the effect of the pulsation by comparing two notch types (circular type and V type). Then, we extend our analysis to a nine-piston pump model. This paper not only confirms the effect of the pressure/flow pulsation according to pulsation variables but can also be applied to the development of a SimulationX$^{(R)}$-based simulation technique for notch-shape optimization for a swash-plate-type variable piston pump.

• IE interfaces
• /
• v.12 no.1
• /
• pp.68-78
• /
• 1999

A noncircular cutting such as a piston cutting has depended on the copy-machining because of its complex shape. But the copy-machining needs a master model and brings about a low quality of the piston caused by being worn out of the master model. And the lower cutting speed reduces the productivity. In this paper, for solving these problems, a specialized software system and its subsequent procedure are presented. The shape of a piston consists of an oval, an offset, recesses, and eccentricities. The paper describes these shapes as a consistent equation that is a function of the rotational angle and the position of longitudinal direction(Z-axis). It is simple to define the characteristic geometry of a piston and to generate a tool path for CNC machining. This paper proposes the a proper structure of a 4-axes CNC(Computerized Numerical Control) lathe for machining the piston. As well as X-axis and Z-axis, are attached to the machine a C-axis for rotation and a Y-axis for higher speedy prismatic motion parallel to X-axis.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.842-845
• /
• 2000

The purpose of this paper is to investigate the influences on mechanical properties of motor pistons manufactured by casting, conventional forging and powder forging, using the comparison of characteristics like microstructure, hardness, tensile strength, and elongation. To form conventional forging piston, the experiment of visioplasticity was performed. As the model material, plasticine was used. To form powder forging piston, the shape of piston was simplified as simple cup shape. Material properties like workability, density variation before and after forging, and strain loci of material during forging were investigated. Powder forging and conventional forging technologies were effective to gain dense microstructure. In powder forging, distribution of such dense microstructuer was uniform. For hardness, pistons from powder forging and conventional forging technologies were much better than that from casting. For tensile strength and elongation, powder forging and conventional forging technologies were also advantageous.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.10a
• /
• pp.358-364
• /
• 1998

Lubricational characteristics at the interface between the piston ring and the cylinder liner are considered in this paper. To verify that surface shape and operating conditions of the engine can affect the state of lubrication, the changes of the minimum film thickness and friction force are calculated with various conditions. Oil starvation and open-end boundary condition are used to determine computational boundaries as reported on previous paper for lubrication analysis for the piston ring. From this analysis, it can be found that lubricational characteristics are seriously affected by degree of oil starvation, surface shape and operating conditions.