• Journal of the Korean Institute of Gas
• /
• v.20 no.5
• /
• pp.89-95
• /
• 2016

Keeping the gas pipelines in the common utility tunnel is useful because it has a lower risk of corrosion than conventional burial, and can prevent from excavating construction. But, explosions in common utility tunnels can cause greater damage from the blast overpressure compared to outdoor explosions, due to nature of the confined environment. Despite this fact, however, research on common utility tunnels has been limited to fire hazard and little has been studied on the dangers of explosions. This study developed scenarios of methane gas explosion caused by gas leak from gas piping within the common utility tunnel followed by unknown ignition; the study then calculated the extent of the impact of the explosion on the facilities above, and suggested the needs for designing additional safety measures. Two scenarios were selected per operating condition of safety devices and the consequence analysis was carried out with FLACS, one of the CFD tools for explosion simulation. The overpressures for all scenarios are substantial enough to completely destroy most of the buildings. In addition, we have provided additional measures to secure safety especially reducing incident frequency.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.3 no.1
• /
• pp.31-40
• /
• 2005

High temperature - high pressure apparatus was developed to simulate nickel fewite corrosion products which were main compositions of the radioactive crud in the nuclear power plant. Corrosion product similar to the crud was obtained by a tube accumulator system. Nickel alloy (Inconel 690) and carbon steel (SA106 Gr. C) were corroded at 270 $\^{circ}C$ in the corrosion product generator. Ni ions and Fe ions dissolved by corrosion reaction were able to be transported to the accumulator because the crud generation mechanism was the solubility change with temperature. To evaluate the properties of simulated corrosion products, scanning electron microscope (SEM) observation and EDAX analysis were performed. SEM observation of corrosion product showed the needlelike or crystal structure of oxide depending on precipitating location. The crystal oxide was the nickel ferrite, which was similar to the crud in nuclear power plants.

• Journal of the Korean Geosynthetics Society
• /
• v.14 no.2
• /
• pp.11-21
• /
• 2015

According to the damage investigation in 2002, the failures of river levee were caused by overflow, erosion, and unstable body conditions due to piping, inappropriate embanking materials, and poor compaction. Especially, overflow was identified as a main reason that induces levee failure by 39.5% from the distribution of failure types. The major parameters, such as levee collapsing angle (${\theta}$), levee collapsing rate (k) affect inundation velocity and area size during the analysis of inundation modeling, however, domestic research effort on this area is still insufficient. In this paper authors conducted levee failure experiments of 4 levee height types, 0.20 m, 0.25 m, 0.30 m, and 0.40 m based on theassumption of Froude Similarity (${\lambda}_{Fr}=1$). As a result, the authors suggested a levee failure mechanism according to the levee heights (H), a collapse extension lengthwhich is around, levee collapse angle (${\theta}$), levee collapse rate (k).

• Journal of the Korean Society for Nondestructive Testing
• /
• v.29 no.2
• /
• pp.93-97
• /
• 2009

An advantage of a magnetostrictive strip transducer for a long-range guided wave inspection is that the wave patterns are relatively clear and simple when compared to a conventional piezoelectric ultrasonic transducer. Therefore, if we can characterize the evolution of defect signals, it could be a promising tool for a structural health monitoring of pipes for a long period of time as well as an identification of flaws. However, when evaluating a signal during a realistic field examination, it should be careful because of some spurious signals or false indications, such as signals due to a directionality, multiple reflections, mode conversion, geometrical reflections etc. Mode converted signals from a realistic piping mockup were acquired and analysed. We found mode conversions between a torsional guided wave T(0,1) mode and a flexural F(1,3) or longitudinal L(0,2) mode generated by a magnetostrictive strip transducer. Based on the experimental observations, an interpretation of the source of the mode conversion is discussed in a viewpoint of electromagnetic properties and structure of the strip transducer.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.10 no.2 s.21
• /
• pp.41-47
• /
• 2004

Plate has cutout inner bottom and girder and Door etc. in hull construction absence is used much, and this is strength in case must be situated, but establish in region that high stress interacts sometimes fatally in region that there is no big problem usually by purpose of weight reduction, a person and freight movement, piping etc.. Because cutout‘s existence is positioning in this place, and, elastic bucking strength by load causes large effect in ultimate strength. Therefore, perforated plate elastic bucking strength and ultimate strength is one of important design criteria to decide structural elements size at early structure design step of a ship. Therefore, we need reasonable & reliable design formula for elastic bucking strength of the perforated plate. The author computed numerically ultimate strength change about several aspect ratios, cutout dimension, and plate thickness by using ANSYS Finite element analysis code based on finite element method in this paper.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.59 no.4
• /
• pp.43-52
• /
• 2017

This study analyzed pore water pressure, earth pressure and settlement through laboratory model tests in order to suggest the effective remodeling method in the case of reinforcing the upstream and downstream slope of deteriorated reservoirs that has no cores and filters or is not functional. The method of remodeling the upstream slope using dredge soil is first prevent seepage by installing the core, and the leakage water can be rapidly discharged through a filter installed on the downstream slope. Therefore, it is considered a highly efficient method of remodeling that reduces piping phenomena and increasing the storage capacity of the reservoir. The variation of earth pressure without the core and filter was greater than with it, while the change largely showed in the upstream slope, the downstream slope did not show any significant changes. The remodeling method of the downstream slope with the core appeared differently pore water pressure depending on the presence of the vertical and horizontal filters. In the upstream slope, the pore water pressure rises sharply, the base and middle gradually increased, and the downstream slope appeared small. The pore water pressure of embankment with a vertical and horizontal filter will be smaller than without it. The remodeling of deteriorated reservoir that does not have the function of the filter, the vertical filter must be installed in a position that is higher than the expected seepage line by removing portions of the downstream slopes. Since the horizontal filter is an important structure that provides stable drainage during an earthquake or concentrated leak, it is necessary to examine any change in the seepage characteristics depending on the filter intervals via three-dimensional finite element analysis, and it should be connected to the tow-drain to reduce the possibility of the collapse of the reservoir.

• Journal of Korea Water Resources Association
• /
• v.47 no.4
• /
• pp.307-319
• /
• 2014

Because of the rapid rising of water related disasters due to the global warming, the extreme design criteria of levee construction for severe flood has been applied in several developed countries such as USA and Netheland. In Korea, the national river restoration projects were carried out on 4 major rivers in recent several years. The projects consisted of riverbed dredge and levee reinforcement, and new construction have caused wide change of river environment. However, concrete countermeasures for levee safety and river management have not been suggested until now. Therefore, this study assesses the levee safety of Yulji levee located in Hoechon, Nakdong Basin, where the Levee Seepage Monitoring System installed. The stability of levee is assessed based on the simulation performed by SEEP/W(2D unsaturated seepage model) and the simulated results are compared with the observed data. The effects of the flood wave and levee shape on the levee safety are investigated through several simulations.

• Corrosion Science and Technology
• /
• v.12 no.6
• /
• pp.280-287
• /
• 2013

Flow accelerated corrosion(FAC) of the carbon steel piping in pressurized water reactors(PWRs) has been major issue in nuclear industry. Severe accident at Surry Unit 2 in 1986 initiated the worldwide interest in this area. Major parameters influencing FAC are material composition, microstructure, water chemistry, and hydrodynamics. Qualitative behaviors of FAC have been well understood but quantitative data about FAC have not been published for proprietary reason. In order to minimize the FAC in PWRs, the optimal method is to control water chemistry factors. Chemistry factors influencing FAC such as pH, corrosion potential, and hydrazine contents were reviewed in this paper. FAC rate decreased with pH up to 10 because magnetite solubility decreased with pH. Corrosion potential is generally controlled dissolved oxygen (DO) and hydrazine in secondary water. DO increased corrosion potential. FAC rate decreased with DO by stabilizing magnetite at low DO concentration or by formation of hematite at high DO concentration. Even though hydrazine is generally used to remove DO, hydrazine itself thermally decomposed to ammonia, nitrogen, and hydrogen raising pH. Hydrazine could react with iron and increased FAC rate. Effect of hydrazine on FAC is rather complex and should be careful in FAC analysis. FAC could be managed by adequate combination of pH, corrosion potential, and hydrazine.

• Spatial Information Research
• /
• v.17 no.1
• /
• pp.103-115
• /
• 2009

Recently, the seabed facility is gradually being increased based on the development of harbor and the coastal area. However, the comparison between the survey data with the chart still shows the significant differences leading to various disasters over sea accident. Therefore, in this study, the investigation on the seabed facility were performed in 5 areas through an accuracy analysis using an up-to-date surveying equipment(MBES, SSS and SBP). Based on the study more systematic management on the seabed facility, more accurate method on the surveying, and some considerations on the related policies are suggested. Through the study, we obtained more accurate measurement on depth and seabed piping forms in Jakdo and Pyong-tack, on sunken ship in a Mok-po, on seabed crater in Je-ju. In addition, it was possible to present the method for the construction of information infra and a connection with the seabed facility. The criteria on the equipment's specification, surveying method and procedures are set by the experiments and the investigation and surveying accuracy on the seabed facilities are also suggested.

• Fashion & Textile Research Journal
• /
• v.18 no.4
• /
• pp.399-411
• /
• 2016

This research reviewed the developmental process of domestic outdoor wear and later analyzed the images given out by men's outdoor wear. The research results are as follows. First, military supplies left by American soldiers were dyed or reformed and then worn, and daily wear were mainly worn in the 1960s. Wears made from light and waterproof materials were worn and equipments were used in the 1970s. High functioning materials which allowed simultaneous breathability, waterproof and thermal insulation functions were used for wears in the 1980s. For the jacket especially, functionality was enhanced sith zippers, snaps and velcro to prevent cold air penetration in the 1990s. Florescent piping decorations and logo decorations, and prints and colors which reflected the trend, were used to emphasize fashionity and decorativeness in the 2000s. Second, Sophisticated image emphasized urban feeling with toned-down windbreaker jackets without much detail, with down jacket and pants. Casual image expressed a relaxed feeling with windbreaker jacket, shirts, jumper, vest and pants made of cotton, mesh knit and denim. Active image emphasized functionality by brightly colored windbreaker jackets, down jacket and pants. Ethnic image expressed an exotic mood with windbreaker jackets with stylized prints, with jumper, down jacket and pants. Military image showed a strong masculine feeling with jackets adorned with epaulettes, khaki colors and camouflage prints, with jumper, T-shirts, vest, shorts and pants. Avantgarde image exuded an experimental and unique feeling with jackets made of various colors and materials, such as cotton, jersey and glossy materials, with down jacket and jersey pants.