• 설비공학논문집
• /
• 제5권3호
• /
• pp.157-168
• /
• 1993

Pipe network of hot water heat supply system in an apartment house was analyzed. Flowrate and supply heat capacity of each household in which constant flowrate balancing valve is installed in a single zone system were calculated and the results were investigated. In the existing piping system, the non-uniformity of heat supply with floors due to the static pressure and temperature difference between supply main and return main can not be avoided and this tendency get intense with the increase of the height of building. The non-uniformity of heat supply can be prevented by the installation of balancing valve at each household, however if the performance of supply pump is not sufficient to overcome the energy loss due to the installation of balancing valve for constant flow rate or if the selection of the valve capacity is not adequate, the valves will may lose their controllability.

• 한국지반공학회지:지반
• /
• 제11권4호
• /
• pp.75-86
• /
• 1995

내관과 외관으로 구성된 모형 개단 말뚝을 압력 토조속에 상이한 설치방법으로 관입한 후,실제 지진 기록을 이용하여 모델링시킨 유사 지진을 작용시켜 개단 말뚝에서의 지지력 저감 특성을 고찰하였다. 유사 지진 진동에 의한 극한 지지력 감소율은, 타격 관입 말뚝에서 약 20%였으며, 진동 관입 말뚝의 경우 약 40%에 달하였다. 또한,외주변 마찰력의 감소는 극한 지지력 감소의 대부분을 차지하여 약 80%였으며, 선단 강재부 지지력과 관내토 폐색력은 각각 약 10%였으며, 이러한 경향은 말뚝의 설치방법에 따라 크게 달라지지 않았다.

• 조명전기설비학회논문지
• /
• 제24권11호
• /
• pp.23-29
• /
• 2010

The principal factor determining an optimum design method for cathodic protection is finding the protection current for preventing the corrosion of existing, already laid pipe. Some factors currently used to test designs include the sizes and lengths of pipes, soil resistivity, and the coating damage rate. We believe this method and current formulae are not optimum due to the uncertainty of determining the coating damage rate and the corrosion protection current's density. This paper analyzes the amount of protection current obtained by performing a temporary current test using data describing existing laid pipe. We then propose determining the corrosion protection current by using the temporary current test after modifying the formula. In addition, we suggest a way to choose optimized cathodic protection and the process of design by executing the design and taking account of such factors as a site condition of 34km-long non-protected water supply pipe lines (stages I and II) in ${\bigcirc}{\bigcirc}$ region, climate, interferences, and durability.

• 한국조명전기설비학회지:조명전기설비
• /
• 제6권5호
• /
• pp.38-44
• /
• 1992

In this paper, electrification pipe modeled on the oil path that insulating oil flow in the high power transformer is manufactured in order to prevent the accident cause from streaming electrification generated when insulating off flow at a solid-liquid interface, and the streaming current is measured and analyzed according to the shape of oil path in electrification pipe. From the result of this study, the streaming current increases linearly with increasing of a oil velocity and it increases at lower temperature and decreases at higher temperature than [$46^{\circ}C$]. The smoother the flow of insulating oil is the more the streaming current decreases.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 춘계학술대회 논문집 전기설비전문위원
• /
• pp.58-60
• /
• 2007

This paper introduces the IN-FLEX system using aluminum clad flex cable, which is expected to alternate the conventional wiring method, such as, a steel pipe wiring method, and a synthetic resin pipe wiring method. The aluminum clad flex cable has a superior operation characteristics in heat dissipation property, in installation and maintenance facility, flammability, and appearance. Moreover, the IN-FLEX system adopted an easy connection mechanism which enable to reduce the time, hands and expense for the installation and maintenance of the system. Certification tests verifying the superior operation characteristics and reliability of the system using aluminum clad flex cable were carried with standard method in KOLAS certification institute.

• 한국조명전기설비학회지:조명전기설비
• /
• 제8권6호
• /
• pp.56-62
• /
• 1994

유동대전 현상을 밝히기 위해 간단한 유순환 장치에 설치된 프레스보드관(pressboard pipe)을 통하여 변압기 유를 순환시키면서 기초적인 실험을 행하였다. 특히, 측정 전극에 교류전계를 인가할 때 이것이 유동대전에 미치는 영향에 대하여 고찰하였다. 측정값은 절연유내에 분포된 전하의 분리와 완화에 기초를 둔 이론적 개념으로부터 유도된 공식에 의하여 검토되었다. 유동 대전은 외부에 교류전계를 인가하는 것에 의하여 증가하는 경향을 나타냈으며, 이는 교류전계의 전기력이 계면부근의 절연유내에 분포되어 있는 과잉전하에 영향을 준 결과로 나타난 현상임을 알 수 있었다.

• 한국안전학회지
• /
• 제23권5호
• /
• pp.79-83
• /
• 2008

The corrugated stainless steel tubing(CSST) for the fuel gas piping system can be installed easily and quickly. It is often constructed under the ceiling and the wall which has a good flexibility and installation in comparison with iron pipe. However, the quality of the CSST is determined to depend upon the welding skill of stainless steel tubing. In this study, it is tested by controlling jet point of Ar as inert and cooling gas, and also compared with the bead state of welding point and the performance. As a result, it has the best condition when the jet point of Ar is located behind $5{\sim}10mm$ of the welding point.

• 한국가시화정보학회지
• /
• 제14권3호
• /
• pp.15-21
• /
• 2016

The circular and flat heat pipe were experimentally investigated by using neutron imaging technique. This experimental study was performed at the DINGO of OPAL research reactor, Australia. The diameter of the circular heat pipe is 10 mm and the dimension of flat is $10(width){\times}3(thickness)mm2$, respectively. We used the distilled water as a coolant. The coolant distributions and 2-phase flow patterns were measured under heating conditions. Experimental results show that neutron imaging technique is a good tool to visualize the 2-phase flow and phenomena in the heat pipe. The coolant distributions and 2-phase flow patterns depend on installation posture of the heat pipe and volume ratio of the coolant. Finally, it was discussed to calculate the void fraction by neutron imaging technique.

• Nuclear Engineering and Technology
• /
• 제41권3호
• /
• pp.287-294
• /
• 2009

Due to thermal hydraulics phenomena, such as thermal stratification, various events occur to the parts of a nuclear power plant during their lifetimes: e.g. cracked and dislocated pipes and thermally fatigued, bent, and damaged supports. Due to the operational characteristics of the parts of the steam generator feedwater inlet horizontal pipe, thermal stratification takes place particularly frequently. However, the thermal stress due to thermal stratification at the steam generator feedwater inlet horizontal pipe was not reflected in the design stage of old plants(Kori Unit No.1, 2, 3 and 4, Yeonggwang Unit No. 1 and 2, and Uljin Unit No. 1 and 2; referred to as old-style power plants hereinafter). Accordingly, a verification experiment was performed for thermal stratification in the horizontal inlet nozzle steam generator of old-style plants. If thermal stratification occurred in the horizontal pipe of an old-style power plant, numerical analysis of the temperature distribution of the pipes and fluids was conducted. The temperature distributions were compared at the curved part of the pipe and the horizontal pipe before and after the installation of the improved thermal sleeves designed to alleviate thermal stress due to thermal stratification. The thermal stress reduction measure was proven effective at the steam generator inlet horizontal pipe and the curved part of the pipe.

• 대한조선학회논문집
• /
• 제56권2호
• /
• pp.152-160
• /
• 2019

In this study, we propose a piping material supply management method using CAD system. The piping materials installed in super large offshore plants have very complicated connection conditions. Therefore, it is very difficult to determine the order of receipt of a large number of installation materials. Therefore, we have developed a system that can automatically check the preparation rate of installation materials prior to the installation process. We have developed an algorithm to obtain connection information among installation items from PDMS system. We have developed an algorithm that can determine the order of installation materials to be installed using the connection information. The order of the installation material is determined by taking into account the constraint conditions for the complete installation of the piping material. We confirm the effectiveness of the developed algorithms in the operating system. This system is also used to manage installation schedules and plan the installation manpower.