• Journal of the Mineralogical Society of Korea
• /
• v.15 no.4
• /
• pp.315-327
• /
• 2002

Al-pillared clay was synthesized by constructing pillars of aluminum oxides at the interlayer of montmorillonite in bentonite. XRD, DTA and chemical analyses of Al-pillared clay were performed to examine mineralogical properties. Batch adsorption experiments were also conducted to determine the adsorption properties of this synthesized clay for phosphate ions. XRD analyses showed that the interlayer space of Al-pillared clay expanded to 18.03 $\AA$ at room temperature and shifted to $17 \AA$ after heating to $550^{\circ}C$. A small change in interlayer space after heating indicates high thermal stability. The interlayer expansion by glycerol was also very small. From DTA analyses, pillared clay showed the characteristic endothermic peaks at 270 and $420^{\circ}C$ , which might be caused by dehydration in framework of pillars between interlayers. Adsorption experiment revealed that Al-pillared clay had an excellent adsorption capacity to the phosphate ions, whereas montmorillonite had very low adsorption capacity to phosphate ions. In phosphate solution concentration up to 300 mg/L, 2 g of pillared clay could uptake almost 100% of phosphate ions from 20 mL of solution. After heat treatment of the phosphate adsorbed pillared clay at 50$0^{\circ}C$ to remove phosphate, the calcined pillared clay could adsorb phosphate ions with a little decreased adsorption efficiency. This fact indicates that Al-pillared clay can be recycled for the adsorption of phosphate ions.

• Applied Chemistry for Engineering
• /
• v.10 no.2
• /
• pp.304-309
• /
• 1999

Aluminum-pillared clay was prepared by the intercalation of Al-hydroxy oligomer into domestic bentonite. The solid products are characterized by XRD, nitrogen adsorption/desorption, EDX, and SEM. The solid products show relatively high specific surface areas in the range of $104{\sim}228m^2/g$, and their specific surface area, micropore surface area, and micropore volume increase with increasing the mole ratio of OH/Al. From the results of pore size distribution calculated by BJH equation, it was found that aluminum-pillared clay also contains much mesopore near $40{\AA}$. These results indicate that Al-hydroxy oligomer was intercalated into bentonite, and aluminum oxide was pillared among the layers of bentonite, and micropore and mesopore was finally developed into layers. As OH/Al mole ratio increases, the thermal stability of aluminum-pillared clay increases. This result can be explained by the fact that the density of layers is increased due to the formation of aluminum pillars.

• Bulletin of the Korean Chemical Society
• /
• v.21 no.10
• /
• pp.1049-1051
• /
• 2000

A chromia-pillared clay has been prepared by ion exchange type intercalation reaction between the sodium ion in montmorillonite and the trimeric chromium oxyformate (TCF) ion, and by subsequent heat-treatment. The structural and thermal properties have been systematically studied by thermal analysis, powder XRD, IR spec-troscopy, and XAS. The gallery height of~6.8 $\AA$ upon intercalation of the TCF ion suggests that the $Cr_3O$ plane is parallel to the aluminosilicate layers. Even though the basal spacing of TCF intercalated clay decreases slightly upon heating, the layer structure was retained up to $550^{\circ}C$ as confirmed by XRD and TG/DTA. Ac-cording to the EXAFS spectroscopic analysis, it is identified that the (Cr-Cr) distance of 3.28 $\AA$ between vertex-linked CrO6 octahedra in TCF splits into 2.64 $\AA$, 2.98 $\AA$, and 3.77 $\AA$ due to the face-, edge-, and corner-shared CrO6 octahedra after heating at $400^{\circ}C$, implying that a nano-sized chromium oxide phase was stabilized within the interlayer space of clay.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2006.06a
• /
• pp.23-24
• /
• 2006

The International Maritime Organization announced that the regulation of nitrogen oxide put into force for vessels constructed after 2000 from May, 2005 as agenda is satisfied on May, 2004. A honeycomb-typed Pillared Inter-Layered Clay(PILC) catalyst was developed for do-NOx SCR system in 2004. This catalyst has been applied to 9H25/33 engine that is one of the main diesel engines in Engine Machinery Division of the Hyundai Heavy Industries CO., LTD. In addition, we have tried to develop better catalysts in the aspects of easy synthetic method and performance.

• Bulletin of the Korean Chemical Society
• /
• v.19 no.11
• /
• pp.1185-1188
• /
• 1998

Layered nanocomposite, SiO2/TiO2 sol pillared clay, has been prepared by the ion exchange reaction of Na' ion in montmorillonite with positively charged mixed SiO2/TiO2 sol. The nanosized sol particles were synthesized by mixing SiO2 sol solution with TiO2 one, which is obtained by acidic hydrolysis of TEOS and TiCl4, respectively. From powder XRD, the basal spacing (d001) of the sample calcined at 400 ℃ was found to be ca. 60 Å, due to the multistacking of nanosized SiO2 and TiO2 sol particles, which was confirmed by the pore size analysis from 129Xe NMR and micropore analysis calculated from nitrogen adsorption. The BET specific surface area shows the value of 684 m2g-1 (Langmuir 1115 m2g-1), which is the highest among various pillared clays ever reported previously, and the total porosity is found to be 0.51 mlg-1, and the pores are mainly composed of micropore with a size of ca. 11.8 Å. This result agrees with the adsorption capacity obtained from water adsorption. According to diffuse reflectance ultraviolet-visible spectroscopy, it is found that the TiO2 particles stabilized in the interlayer space of montmorillonite are quantum-sized of ca. 20 Å.

• Environmental Engineering Research
• /
• v.25 no.2
• /
• pp.186-196
• /
• 2020

Pillared clays with Zr and Fe/Cu/Zr polycations have been prepared from natural clays found in large deposits of Kazakhstan and assessed as catalysts for the catalytic wet peroxide oxidation (CWPO), using 4-nitrophenol (4-NP) as model compound. The performance of the catalysts was followed by measuring the concentration of 4-NP, H₂O₂ and the total organic carbon (TOC), considering C_4-NP = 5 g L^-1, $C_{H_2O_2}$ = 17.8 g L^-1, C_cat = 2.5 g L^-1, initial pH = 3.0 and T = 50℃. At those selected conditions, the pillared clays showed higher activity than natural clays in the CWPO of 4-NP. The conversion of the model pollutant was complete when Fe/Cu/Zr-PILCs were used, with the TOC removal reaching 78.4% after 24 h with the best Fe/Cu/Zr-PILC. The H₂O₂, 4-NP and TOC time-evolution was well described by a kinetic model based on TOC lumps in three blocks, considering the initial TOC (corresponding to 4-NP), the production of oxidizable intermediates and the formation of refractory products.

• Journal of the Korean Ceramic Society
• /
• v.41 no.1
• /
• pp.81-85
• /
• 2004

Nanoporous materials with nanometer-sized pores, are of great interest in the various applications such as selective adsorbents, heterogeneous catalysts and catalyst supports because of their high porosity, surface area, and size selective adsorption properties. This study is aimed to prepare nanoporous catalytic materials on the basis of two-dimersional clay by pillaring of $SiO_2$ sol particles. $SiO_2$ Pillared Montmorillonite (Si-PILM) was prepared by ion exchanging the interlayer $Ni^{2+}$ ions of clay with $SiO_2$ nano-sized particles of which the surface was modified with nicked polyhydroxy cations sach as $Ni_4(OH)_4^{4+}$. Nano-sized $SiO_2$ particles were formed by the controlled hydrolysis of tetraethyl orthosilicate (TEOS). Upon pillaring of $Ni^+$-modified $SiO_2$ nano particles between the clay layers, the basal spacing was expanded largely to $45{\AA}$ and the extremely large specific surface area ($S_{BET}$) of $760m^2/g$ was obtained.

• Journal of Korean Society on Water Environment
• /
• v.23 no.6
• /
• pp.966-972
• /
• 2007

A novel organoclay has been developed with aluminium-pillared clay modified with an amphoteric surfactant, N-Dodecyl-N,N-dimethyl-3-ammonio-1-propanesulfonate (DDAPS). This novel organoclay is expected to have phosphorus removal capacity as well as organic and inorganic contaminant removal capacity, due to aluminum inside the clay structure. It also exhibited less surfactant desorption than conventional cation surfactant-based organoclays. Phosphorus in water can be decreased from 0.2 mg/L to 0.0012 mg/L in 27 hours with this organoclay. Also, cadmium could removed from water using this proposed organo-clay. Experiments were performed under various pHs and amphoteric surfactants sorption capability was the highest at pH 5 when more of the amphoteric surfactant head group took on positive charges.

• Proceedings of the Korea Air Pollution Research Association Conference
• /
• 2003.05b
• /
• pp.99-99
• /
• 2003

육상에서 발생하는 공해 물질뿐만 아니라 해상에서 발생하는 공해 물질에 대한 관심이 높아진 가운데 선박에서 발생하는 탄화수소, 질소산화물, 일산화탄소, 이산화황 및 입자상 물질의 규제에 관한 방안이 가시화되고 있는 현실이다. 선박엔진에서 발생하는 질소산화물 제거 연구를 위해서 당사에서는 엔진 연료 분사 시스템에 관한 연구와 더불어 후처리 설비인 SCR 연구를 병행하고 있다. 본 연구는 당사 개발 촉매인 PILC(Pillared Interlayer Clay)를 이용한 SCR 적용에 관한 연구 결과중 촉매 특성에 관한 부분이다. (중략)

• Environmental Engineering Research
• /
• v.21 no.2
• /
• pp.203-210
• /
• 2016

Hybrid materials were obtained modifying the bentonite (BC) and local clay (LC) using hexadecyltrimethylammonium bromide (HDTMA) or the clay were pillared with aluminum followed by modification with HDTMA. The materials were characterized by the SEM, FT-IR and XRD analytical tools. The batch reactor data implied that the uptake of $17{\beta}$-estradiol (E2) by the hybrid materials showed very high uptake at the neutral pH region. However, at higher and lower pH conditions, slightly less uptake of E2 was occurred. The uptake of E2 was insignificantly affected changing the sorptive concentration from 1.0 to 10.0 mg/L and the background electrolyte (NaCl) concentrations from 0.0001 to 0.1 mol/L. Moreover, the sorption of E2 by these hybrid materials was fairly efficient since within 30 mins of contact time, an apparent equilibrium between solid and solution was achieved, and the data was best fitted to the PSO (pseudo-second order) and FL-PSO (Fractal-like-pseudo second order) kinetic models compared to the PFO (pseudo-first order) model. The fixed-bed column results showed that relatively high breakthrough volume was obtained for the attenuation of E2 using these hybrid materials, and the loading capacity of E2 was estimated to be 75.984, 63.757, 58.965 and 49.746 mg/g for the solids BCH, BCAH, LCH and LCAH, respectively.