• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.12
• /
• pp.1118-1122
• /
• 2006

In this study, in order to develop the low temperature sintering multilayer piezoelectric actuator, PMN-PNN-PZT system ceramics were manufactured and their microstructure, ferroelectric and piezoelectric properties were investigated. By increasing sintering temperature, remanent polarization$(P_r)$ was increased due to the increase of sinterability and grain size. However, coercive $field(E_c)$ showed an opposite tendency to remanent polarization owing to the feasibility of domain wall motion. At the sintering temperature of $900^{\circ}C$, dielectric $constant({\varepsilon}_r)$, electromechanical coupling $factor(k_p)$, piezoelectric $constant(d_{33})$ and mechanical quality $factor(Q_m)$ showed the optimal value of 1095, 0.60, 363 and 1055, respectively, for multilayer piezoelectric actuator application.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.290-291
• /
• 2007

In this study, in order to develop low temperature sintering ceramics for multilayer piezoelectric actuator, sensers, transducers, PMN-PNN-PZT ceramics were manufacrtured with the sintering temperature, and their piezoelectric and dielectric properties were investigated. At the composition ceramics sintered at $900^{\circ}C$, desity, dielectric constant$({\varepsilon}_r)$, electromechanical coupling factor(kp), piezoelectric constant$(d_{33})$ and mechanical quality factor(Qm) showed the optimal value of $7.86g/cm^3$, 1417, 0.634, 410pC/N and 1138, respectively.

• Journal of the Korean Ceramic Society
• /
• v.51 no.6
• /
• pp.623-628
• /
• 2014

Orthorhombic $Ba(Ti_{0.94}Zr_{0.06})O_3$ single crystals are fabricated using the cost-effective solid-state single crystal growth (SSCG) method; their dielectric and piezoelectric properties are also characterized. Measurements show that (001) $Ba(Ti_{0.94}Zr_{0.06})O_3$ single crystals have an electromechanical coupling factor ($k_{33}$) higher than 0.83, piezoelectric charge constant ($d_{33}$) of about 400 [pC/N], and piezoelectric voltage constant ($g_{33}$) higher than 50 [${\times}10^{-3}Vm/N$]. The transition temperature ($T_{OT}$) of the (001) $Ba(Ti_{0.94}Zr_{0.06})O_3$ single crystals between orthorhombic and tetragonal phases is also observed to be about $61^{\circ}C$. Because their electromechanical coupling factor ($k_{33}$) and piezoelectric voltage constant ($g_{33}$) are higher than those of soft PZT ceramics, it is expected that (001) $Ba(Ti_{0.94}Zr_{0.06})O_3$ single crystals can be used as "lead-free" piezoelectric materials in many piezoelectric applications.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.10
• /
• pp.935-941
• /
• 2006

In this paper, the dielectric and piezoelectric properties of $0.4Pb(Ni_{1/3}Nb_{2/3})O_3+0.6Pb(Zr_{405}Ti_{595})O_3+X\;wt%\;Fe_2O_3$ ceramics were investigated with the addition of $Fe_2O_3$ and sintering temperature. Dielectric constant and piezoelectric constant increased with amount of $Fe_2O_3$ to 0.25 wt% and then decreased the further addition of $Fe_2O_3$. It seems that $Fe_2O_3$ acts as a sintering aid at the sintering temperature of $1150^{\circ}C$. By the addition of $Fe_2O_3$., sintering temperature of the system was lowered from $1250^{\circ}C\;to\;1100^{\circ}C$. The piezoelectric properties showed the maximum value of ${\varepsilon}r=4669,\;d_{33}=810(10^{-12}m/V)$, kp = 77 %, Qm = 55, in $0.4Pb(Ni_{1/3}Nb_{2/3})O_3\;-0.6Pb(Zr_{0.405}Ti_{0.595})O_3+0.25wt%\;Fe_2O_3$ ceramics having composition near the morphotropic phase boundary. The composition may be appropriate for actuator materials because of high piezoelectric constant and electromechanical coupling factor.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.3
• /
• pp.214-219
• /
• 2000

In this paper the structural dielectric and piezoelectric properties of Pb［(M $g_{1}$2// $W_{1}$2/)$_{x}$-(N $i_{1}$3//N $b_{2}$3/)$_{0.15-x-(Zr_{0.5})}$ $Ti_{0.5}$)$_{0.85}$］ $O_3$ (x=0.0~0.10) ceramic were investigated with the substitution of Pb(M $g_{1}$2// $W_{1}$2/) $O_3$. According to the substitution of Pb(M $g_{1}$2//W/1/2/) $O_3$ curie temperatures were slightly decrease due to the decrease of the tetrag-onality of crystal structure and coercive fields were decreased. Up to the substitution of Pb(M $g_{1}$2// $W_{1}$2/) $O_3$ 3mol%,remnant polarization dielectric constant piezoelectric constant were increased. Dielectric constant and electro-mechanical coupling factor( $k_{p}$, $k_{31}$ ) were appeared the highest value of 2230, 0.64, and 0.38 and piezoelectric constant( $d_{33}$ , $d_{31}$ ) was the largest value of 418, 202($\times$10$^{-12}$ /C/N), respectively, when the substitution amount of Pb(M $g_{1}$2// $W_{1}$2/N) respectively, when the substitution amount of Pb(M $g_{1}$2// $W_{1}$2/) $O_3$ was 3mol%.s 3mol%.%.

• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.1
• /
• pp.54-62
• /
• 1994

This paper presents active control methodologies to suppress structural deflections of a composite beam using a distributed piezoelectric-film actuator and sensor. Three types of different controllers are employed to achieve vibration suppression. The controllers are established depending upon the information on the velocity components of the structrue and on the deflection magnitudes as well. They are constant-amplitude controller(CAC), constant-gain mcontroller(CGC), and constant-amplitude-gain controller(CAGC). For the minimization of the residual vibration (chattering in a settled phase), which is the practical shortcoming of the conventional CAC dur to time delay phenomenon of the hardware system, a new control algoritym CAGCis designed by selecting switching constants in an optimal manner with respect to the initial tip deflection and the applied voltage. The experimental investigations of the transient and forced vibration control for the first vibrational mode are undertaken in order to compare the suppression efficiency of each control algorithm. Moreover, simultaneous controllability of various vibrational modes through the proposed scheme is also experimentally verified by pressenting both the transfer function and the phase.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.9
• /
• pp.766-770
• /
• 2007

In this study, in order to develop low temperature sintering ceramics for multilayer piezoelectric actuator, $0.07Pb(Mn_{1/3}Nb_{2/3})O_3-xPb(Ni_{1/3}Nb_{2/3})O_3-(0.93-x)Pb(Zr,Ti)O_3$ ceramics system were fabricated using $Li_2CO_3-Bi_2O_3-CuO$ sintering aids and the specimens were sintered at $930^{\circ}C$. Thereafter, their piezoelectric and dielectric characteristics were investigated according to the amount of PNN substitution. At 9 mol% PNN substitution, density, electromechanical coupling factor ($k_p$), dielectric constant, mechanical quality factor ($Q_m$) and piezoelectric constant ($d_{33}$) showed the optimum value of $7.86g/cm^3$, 0.60, 1640, 1323 and 387 pC/N, respectively. It is considered that these values are suitable for piezoelectric divece application such ad multilayer piezoelectric actuator and ultrasonic vibrator with pure Ag internal electrode.

• Journal of Powder Materials
• /
• v.17 no.5
• /
• pp.404-408
• /
• 2010

The effects of high energy ball-milling (HEBM) on the sintering behavior and piezoelectric properties of 0.1 wt% $Li_2CO_3$ doped 0.8Pb($Mg_{1/3}Nb_{2/3}$)$O_3$-0.2Pb($Zr_{0.475}Ti_{0.525}$)$O_3$ (PMN-PZT) ceramics were investigated. It was found that HEBM treatment was quite effective to reduce the average particle size down to 300 nm, leading to increased density as well as enhanced piezoelectric properties of a sintered specimen even though prolonged HEBM resulted in unwanted secondary phases that caused a degradation of piezoelectric properties. The dielectric constant ($\varepsilon_r$), piezoelectric coupling factor ($k_p$) and piezoelectric constant $d_{33}$ of 0.1 wt% $Li_2CO_3$ doped PMN-PZT ceramics prepared via HEBM for 10 h reached 2040, 0.68 and 554 pC/N, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.12
• /
• pp.1039-1043
• /
• 2007

In this paper, in order to develop low temperature sintering ceramics for multilayer piezoelectric actuator application, PMN-PZN-PZT ceramics were fabricated using $LiCO_3,\;Bi_2O_3$ and CuO as sintering aids. And also, their piezoelectric and dielectric properties were investigated according to the milling time. All the specimens sintered at $930\;^{\circ}C$ showed tetragonal phases without secondary phases. With increasing milling time, piezoelectric and dielectric characteristic of specimens increased up to 60 hours milling time and then decreased due to the agglomeration of fine particle. Accordingly, it seems that 60 hour is optimum milling condition. At the sintering temperature of $930\;^{\circ}C$ and milling time of 60 hour, density, dielectric constant(${\varepsilon}_r$), electromechanical coupling factor (kp), mechanical quality factor (Qm), piezoelectric d constant showed the optimum value of $7.95\;g/m^3$, 1382, 0.546, 1749, 330 pC/N, respectively for multilayer piezoelectric actuator application.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.1
• /
• pp.35-39
• /
• 2006

In this study, in order to develop the multilayer piezoelectric actuator and ultrasonic resonator, PMN-PNN-PZT ceramics were fabricated by sintering with $Li_2CO_3-Na_2CO_3$ as sintering aids at $950^{\circ}C$ and their piezoelectric and dielectric characteristics were investigated as a function of PNN substitution. With increasing PNN substitution, dielectric constant(${\epsilon}_r$), electromechanical coupling factor(kp), and piezoelectric d constant($d_{33}$) were increased to $12 mol\%$ PNN substitution and then showed a tendency to decrease rapidly With increasing PNN substitution, crystal structure changed from tetragonal to rhombohedral at $12 mol\%$ PNN substitution and then secondary phase was appeared and its intensity was increased. At the $12 mol\%$ PNN substituted PMN-PZT composition ceramic sintered at $950^{\circ}C$, density, kp, $d_{33}$ and Qm showed the optimum value of $7.79 g/cm^3$, 0.599, 419 pC/N, and 894, respectively for multilayer piezoelectric actuator application.