• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2019년도 추계 학술논문 발표대회
• /
• pp.35-36
• /
• 2019

Major influence factors for piercing depth of concrete against small caliber bullet are target's property such as compression strength of concrete and bullet's property such as the velocity and weight of it. In particular about the bullet's property, velocity and incidence angle could be controlled by specific position or distance between targets and shooter, but the angle of yaw of bullet dose not. Because the the angle of yaw of bullet causes lower piercing force of bullet, some errors on piercing depth of concrete could be appeared by live fire test for the evaluation of protective performance. Therefore, we have checked the error canceling effect on the piercing depth of concrete by single shot and barrage of small caiber bullets. As a result, we identified that the error of piercing depth by the angle of yaw of bullet could be cancelled by barrage.

• 소성∙가공
• /
• 제21권3호
• /
• pp.202-206
• /
• 2012

Marking is a process that engraves letters or a pattern onto the surface of sheet metal. During marking, it is important to set the proper working conditions for clarity of the letters. In this study a simple case for forming circular protrusions by half-piercing and embossing was initially attempted to determine the working conditions which gave good results with respect to shape accuracy. Corner-radius and flatness of circular protrusions made under several experimental conditions were measured and compared. It is shown that the precision of protrusions by half-piercing is superior to that of embossing, and the clearance between punch and die exerts a strong influence on the shape accuracy rather than the penetration percentage into the thickness of the sheet metal. The marking dies for "SNUT" letters, as an example, by applying the above results were manufactured with four different clearances. The working variables for the experiment were clearance and marking depth. For the very shallow depth of 0.1mm the letters were not clearly read. Letters marked under other conditions were easily distinguished with increasing marking depth. It was confirmed that the half-piercing technique with proper values of the working variables gives good quality for the marking of sheet metal.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2004년도 학술발표회
• /
• pp.557-562
• /
• 2004

A surface-piercing barrier model is presented for understanding morphological development in the sheltered region and investigating the main factors causing the severe accumulation. Surface-piercing structures like vertical barriers, surface docks and floating breakwaters are recently favored from the point of view of a marine scenario since they do not in general partition the natural sea. The numerical solutions are compared with experimental data on wave profiles and morphological change rates within a rectangular harbor of a constant depth protected by surface-piercing thin breakwaters as a simplified problem. Our numerical study involves several modules: 1) wave dynamics analyzed by a plane-wave approximation, 2) suspended sediment transport combined with sediment erosion-deposition model, and 3) concurrent morphological changes. Scattering waves are solved by using a plane wave method without inclusion of evanescent modes. Evanescent modes are only considered in predicting the reflection ratio against the vertical barrier and energy losses due to vortex shedding from the lower edge of plate are taken into account. A new relationship to relate the near-bed concentration to the depth-mean concentration is presented by analyzing the vertical structure of concentration. The numerical solutions were also compared with experimental data on morphological changes within a rectangular harbor of constant water depth. Through the numerical experiments, the vortex-induced flow appears to be not ignorable in predicting the morphological changes although the immersion depth of a plate is not deep.

• 한국군사과학기술학회지
• /
• 제10권2호
• /
• pp.69-75
• /
• 2007

So far, anti-piercing depths for concrete slabs have been determined using Conventional Weapon's Effects Program(CONWEP) that was developed by the U. S. Army's Corps of Engineering. However, it has been suggested by a number of field officers that the values computed by CONWEP tend to be too high for protective facilities used in small military units and that indiscriminate application of these values to such facilities would lead to uneconomical penetration-proof designs. In this study, gunshots onto RC slabs were carried out using KM80 bullets in order to measure the piercing depths. The observed depths and the depths offered by the CONWEP system differed greatly from each other by up to 119 centimeters. Based on the depth values obtained through this experiment, we have proposed a new equation to calculate effective anti-piercing depths for RC slabs against small caliber bullets.

• 소성∙가공
• /
• 제23권1호
• /
• pp.23-28
• /
• 2014

The aspect ratio of a hole is defined as the ratio of the thickness to the diameter of the sheet metal. Most holes in the sheet metal industry are made by piercing. However, for thick sheets, which have an aspect ratio greater than 2, a machining process like drilling instead of piercing is usually used to make holes. In the current study, piercing, which is a shearing process, is evaluated to punch a hole with a high aspect ratio by using a newly designed die set-up. The piercing die was manufactured to prevent the punch from buckling and also to improve the alignment between the die components. An aluminum alloy sheet was selected for the experiments. The influence of several process parameters such as sheet thickness, clearance and stripping force were investigated. Experimentally, a hole with an aspect ratio of 5 was pierced. The resulting hole had a clean surface and the dimensional accuracy of pierced hole was considerably improved with decreasing clearance between punch and die. It is also shown that the larger penetration depth of the effective sheared surface can be achieved for high aspect ratio piercing relative to conventional piercing with a low aspect ratio.

• 해양환경안전학회지
• /
• 제20권3호
• /
• pp.312-317
• /
• 2014

In this paper, the wave run-up height and depression depth around air-water interface-piercing circular cylinder have been numerically studied. The Reynolds Averaged Navier-Stokes equations (RANS) and continuity equations are solved with Reynolds Stress model (RSM) and volume of fluid (VOF) method as turbulence model and free surface modeling, respectively. A commercial Computational Fluid Dynamics (CFD) software "Star-CCM+" has been used for the current simulations. Various Froude numbers ranged from 0.2 to 1.6 are used to investigate the change of air-water interface structures around the cylinder and experimental data and theoretical values by Bernoulli are compared. The present results showed a good agreement with other studies. Kelvin waves behind the cylinder were generated and its wave lengths are longer as Froude numbers increase and they have good agreement with theoretical values. And its angles are smaller with the increase of Froude numbers.

• 소성∙가공
• /
• 제22권8호
• /
• pp.437-441
• /
• 2013

Recently, the engraving of letters or a pattern on a product surface has received more attention especially in trying to satisfy the customer requirements. Half-piecing is a protrusion forming process that pierces only 40~50% of the material thickness. In the current study, the half-piercing technique for making clear letters by protruding sheet material was selected and studied. The influence of clearance and penetration depth was investigated by measuring the camber and extruded length of a protrusion after experiments. In addition, a numerical analysis was performed for the same working conditions and compared with experimental results. It is shown that, as the clearance increases, the camber of a protrusion increases rapidly and the extruded length decreases slightly. The deformation pattern around the cutting edge during half-piercing changes from an extrusion mode to a shearing mode as the clearance changes from minus to plus values. It is also confirmed that the experimental results show a good agreement with the numerical analyses.

• Design & Manufacturing
• /
• 제2권3호
• /
• pp.40-44
• /
• 2008

Shaving in sheet metal forming is defined as a finish process to make the sheared surface clean which was blanked or pierced in the previous shearing stage. In this study the new shaving technique is applied to the progressive operation. The specimen is automatically fed by continuous movement of the strip. Which improve the positioning accuracy higher. For this study a square part which consist of blanking and piercing is selected for investigation and the progressive die which includes pre-piercing, pierce-shaving, half-blanking and blank-shaving etc is prepared for specimens of steel sheet(SPCC) and aluminum alloy sheet(AL5052). Experiments are carried out for several working variables such as shaving allowance, pre-shearing clearance and relative half-blanking depth. Consequently it was confirmed that the shaving by progressive die can be successfully employed to produce the clean parts requiring shaving process and optimum working conditions for shaving SPCC and AL5052 sheet metal are shaving allowance of 0.2mm(1.3% of thickness) and pre-shearing clearance of 5%.

• 대한조선학회논문집
• /
• 제30권1호
• /
• pp.104-114
• /
• 1993

본 논문에서는 점성유동에 미치는 자유표면의 영향을 조사하기 위하여 자유표면을 수직으로 관통하는 원통 주위의 유동을 수치 시뮬레이션 하였다. 수치해석 방법으로서 Artificial Compressibility Method를 사용하였으며, 계산은 낮은 레이놀드수의 영역에 국한하였다. 계산결과는 자유표면에 가까운 유체영역에서 유선, 점성항력 등에 적지않은 영향이 있음을 보여주고 있다. 자유표면의 존재는 물체 후류 중의 와류를 물체로 부터 분리시키는 방향으로, 점성항력을 감소시키는 방향으로 작용하는 것으로 보인다.

• 한국건축시공학회지
• /
• 제20권1호
• /
• pp.43-51
• /
• 2020

소부대 방호시설의 주된 목적은 적의 모든 무기체계에 대한 완벽한 방호가 아니며, 한국군의 경우, 지근탄에 대한 방호를 적용하고 있다. 특히 소구경 탄자의 경우, KM 80탄을 기준으로 설정하고 있는데, 이에 대한 경험적 설계방법과 구조공학적 설계방법 모두 현실을 제대로 반영하지 못한다는 선행연구들이 있다. 이에 실사격 실험을 수행한 선행연구에서는 콘크리트 슬래브의 소구경 탄자에 대한 관입저항력 계산식을 제안한 바 있다. 그러나, 해당 실험에서는 콘크리트 강도만을 변수로 설정하였고 콘크리트의의 두께, 굵은골재의 종류, 탄자의 편주각, 고강도 콘크리트 등에 대한 변수가 고려되지 않았다. 따라서 본 연구에서는 콘크리트의 두께와 자철광의 함량에 따른 방탄성능을 평가하였다. 그 결과 탄자의 편주각에 의한 오차를 연발사격에 의해 상쇄시킬 수 있다는 것과 자철광의 함량과 콘크리트 두께는 방호성능 향상에 영향을 주지 않는다는 것을 통계적으로 확인하였다.