• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 C
• /
• pp.1378-1380
• /
• 2001

Ohmic contacts have been fabricated on p-type 4H-SiC using Pt/Ti. Low resistivitf Ohmic contacts of Pt/Ti to p-type 4H-SiC were investigated. Specific contact resistances were measured using the transmission line model method, and the physical properties of the contacts were examined using x-ray diffraction, scanning electron microscopy. Ohmic behavior with linear current-voltage characteristics was observed following anneals at $900^{\circ}C$ for 90sec at a pressure of $3.4{\times}10^{-5}$ Torr. The Pt/Si/Ti films was measured lower value of the specific contact resistance by the annealing process, and the contact resistances were improved more than one order compared to Ti contact the annealed sample. Scanning electron microscopy shows that the Pt layer effectively reduce the oxidation of Ti films. And results are obtained as $4.6{\times}10^{-4}$ ohm/$cm^2$ for a Pt/Ti metal structure after a vacuum annealing at $900^{\circ}C$ for 90sec. Titanium has a relatively high melting point, thus Ti-based metal contacts were attempted in this study.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.209.2-209.2
• /
• 2015

Two dimensional layered materials, such as transition metal dichalcogenides (TMDs) family have been attracted significant attention due to novel physical and chemical properties. Among them, molybdenum disulfide ($MoS_2$) has novel physical phenomena such as absence of dangling bonds, lack of inversion symmetry, valley degrees of freedom. Previous studies have shown that the interface of metal/$MoS_2$ contacts significantly affects device performance due to presence of a scalable Schottky barrier height at their interface, resulting voltage drops and restricting carrier injection. In this study, we report a new device structure by using few-layer graphene as the bottom interconnections, in order to offer Schottky barrier free contact to bi-layer $MoS_2$. The fabrication of process start with mechanically exfoliates bulk graphite that served as the source/drain electrodes. The semiconducting $MoS_2$ flake was deposited onto a $SiO_2$ (280 nm-thick)/Si substrate in which graphene electrodes were pre-deposited. To evaluate the barrier height of contact, we employed thermionic-emission theory to describe our experimental findings. We demonstrate that, the Schottky barrier height dramatically decreases from 300 to 0 meV as function of gate voltages, and further becomes negative values. Our findings suggested that, few-layer graphene could be able to realize ohmic contact and to provide new opportunities in ohmic formations.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.764-768
• /
• 2002

Characteristics of ohmic Co/Si/Co contacts to n-type 4H-SiC are investigated systematically. The ohmic contacts were formed by annealing Co/Si/Co sputtered sequentially. The annealings were performed at $800^{\circ}C$ using RTP in vacuum ambient and $Ar:H_2$(9:1) ambient, respectively. The specific contact resistivity$(\rho_c)$, sheet resistance$(R_s)$, contact resistance$(R_c)$, transfer length$(L_T)$ were calculated from resistance$(R_T)$ versus contact spacing(d) measurements obtained from TLM(transmission line method) structure. While the resulting measurement values of sample annealed at vacuum ambient were $\rho_c=1.0{\tiimes}10^{-5}{\Omega}cm^2$, $R_c=20{\Omega}$ and $L_T$ = 6.0 those of sample annealed at $Ar:H_2$(9:1) ambient were $\rho_c=4.0{\tiimes}10^{-6}{\Omega}cm^2$, $R_c=4.0{\Omega}$ and $L_T$ = 2.0. The physical properties of contacts were examined using XRD and AES. The results showed that cobalt silicide was formed on SiC and Co was migrated into SiC.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집 Vol.14 No.1
• /
• pp.197-200
• /
• 2001

In this letter, we report on the investigation of Ni/Si/Ni Ohmic contacts to n-type 4H-SiC. Ohmic contacts have been formed by a vacuum annealing and $N_2$ gas ambient annealing method at $950^{\circ}C$ for 10 min. The specific contact resistivity ( $\rho_{c}$ ), sheet resistance($R_s$), contact resistance($R_c$), transfer length($L_T$) were calculated from resistance($R_T$) versus contact spacing(d) measurements obtained from 10 TLM(transmission line method) structures. The resulting average values of vacuum annealing sample were $\rho_{c}=3.8{\times}10^{-5}\Omega cm^{3}$, $R_{c}=4.9{\Omega}$, $R_{T}=9.8{\Omega}$ and $L_{T}=15.5{\mu}m$, resulting average values of another sample were $\rho_{c}=2.29{\times}10^{-4}\Omega cm^{3}$, $R_{c}=12.9{\Omega}$ and $R_{T}=25.8{\Omega}$. The physical properties of contacts were examined using X-Ray Diffraction and Auger analysis, there was a uniform intermixing of the Si and Ni, migration of Ni into the SiC.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2002년도 추계기술심포지움논문집
• /
• pp.73-77
• /
• 2002

n형 SiC를 이용한 오옴성 접합을 알아보고자 Cu/Si/Cu 형태의 접합실험을 실시하였다. 오옴성 접합의 형성을 위하여 Cu/Si/Cu를 증착 하고 열처리를 시행하였다. 열처리는 RTP를 이용한 진공상태의 2-step 방법으로 시행하였다. 접합에 계산을 위하여 TLM구조로, 면 저항(Rs), 접촉저항(Rc), 이동거리(L$_{T}$), 패드간거리(d), 저항(R$_{T}$)값을 구하면 접합비 저항(Pc) 값을 알 수 있다. 이로 인한 결과 값은 접촉저항 값은 2$\Omega$이었고, 이동간 거리는 1$\mu\textrm{m}$이었으며 접합비저항($\rho$c)=1.0x$10^{-6}$ $\Omega$$\textrm{cm}^2$ 값을 얻을 수 있었다. 물리적 변화를 AES 및 XRD를 이용하여 알아보았다. SiC 계면 상에 Cu의 변화로 인한 silicide형성이 이루어짐을 알 수 있었다.있었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집
• /
• pp.197-200
• /
• 2001

In this letter, we report on the investigation of Ni/Si/Ni Ohmic contacts to n-type 4H-SiC. Ohmic contacts have been formed by a vacuum annealing and N$_2$ gas ambient annealing method at 950$^{\circ}C$ for 10 min. The specific contact resistivity($\rho$$\sub$c/), sheet resistance(R$\sub$S/), contact resistance(R$\sub$S/), transfer length(LT) were calculated from resistance(R$\sub$T/) versus contact spacing(d) measurements obtained from 10 TLM(transmission line method) structures. The resulting average values of vacuum annealing sample were $\rho$$\sub$c/=3.8x10$\^$-5/ Ω$\textrm{cm}^2$ , R$\sub$c/=4.9Ω, R$\sub$T/=9.8Ω and L$\sub$T/=15.5$\mu\textrm{m}$, resulting average values of another sample were $\rho$$\sub$c/=2.29x10$\^$-4/ Ω$\textrm{cm}^2$ , R$\sub$c/=12.9Ω, R$\sub$T/=25.8Ω. The Physical properties of contacts were examined using X-Ray Diffraction and Auger analysis, there was a uniform intermixing of the Si and Ni, migration of Ni into the SiC.

• IMMUNE NETWORK
• /
• 제9권5호
• /
• pp.158-168
• /
• 2009

Tumor therapy using cytokines has been developed for last two decades. Several recombinant cytokines and tumor cell vaccines produced by cytokine gene transfer have been in clinical trials, but several side effects hamper routine clinical applications. Many cytokines are originally expressed as membrane-bound form and then processed to secretory form exerting paracrine effects. Though functional differences of these two types of cytokines are elusive yet, the membrane-bound form of cytokine may exert its effects on restricted target cells as a juxtacrine, which are in physical contacts. With the efforts to improve antitumor activities of cytokines in cancer patients, developing new strategies to alleviate life-threatening side effects became an inevitable goal of tumor immunologists. Among these, tumor cell vaccines expressing cytokines as membrane-bound form on tumor cell surface have been developed by genetic engineering techniques with the hope of selective stimulation of the target cells that are in cell-to-cell contacts. In this review, recent progress of tumor cell vaccines expressing membrane-bound form of cytokines will be discussed.

• 한국생활과학회지
• /
• 제24권3호
• /
• pp.341-358
• /
• 2015

This study aims to identify predictors of driving cessation among Korean elderly. Data from 2011 Elderly Survey conducted by Ministry of Health and Welfare and Korea Institute for Health and Social Affairs were used for the analysis. Based on Webber, Porter, Menec(2010)'s comprehensive theoretical framework for mobility, the model of this study tests five major determinants of driving cessation including financial, psychosocial, environmental, physical and cognitive factors. Results of logistic regression analysis showed that economic status, marital status, contacts with relatives and friends, residential location, taking medication, muscle strength, age, gender, and job were significant predictors of driving cessation of older drivers. Specifically, lower economic status, unmarried status, less contacts with relatives and friends, living in the city, taking medication, weaker muscle strength, older age, female, non-working status were significant risk factors for driving cessation. Practical implications in light of study findings were discussed.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.518-519
• /
• 2006

A connection between pulse-periodical laser radiation power and stability of liquid-metal contacts between powder particles during selective laser sintering (SLS) is determined based on analysis solving the problem of stability of liquid column in the gravity and capillary forces field. On the grounds of obtained relationships the optimization of pulse-periodical laser radiation power and SLS-process duration is realized, that allows to produce voluminous powder porous materials with pre-determined physical and mechanical properties and surface geometry. Results of metallographic investigations of powder porous materials of titanium powder produced with technological regimes calculated by means of obtained relationships are given in the work

• 전자공학회지
• /
• 제13권1호
• /
• pp.86-95
• /
• 1986

The basic physical principles involved in the operation of monolithic magnetic sensors are reviewed and technological aspects outlined. More or less conventional devices based on Hall effect, magnetoresistance or current path deflection are described. It is shown that such sensors with 2, 3, 4 or 5 terminal contacts are achievable with standard silicon integrated circuit process. Several kinds of magnetodiodes (p+nn+,p+n, Schottky, MOS, memory, CMOS) have been fabricated on Si and on SOS films and present attractive properties. Finally, the magneto-transistor family is discussed with emphasis to split-terminals, CMOS, unijunction and fila-mentary devices.