• Advances in concrete construction
• /
• v.14 no.1
• /
• pp.1-13
• /
• 2022

Due to the physical-chemical characteristics of some bottom ash (BA), there are technical, economic and environmental limitations to find a destination that will add value to it. In Brazil, this residue is eventually used for filling coal extraction pits or remains in sedimentation ponds, creating a susceptible panorama to environmental issues. The geopolymers binders are one of the alternatives to the proper use high amounts of these materials. In this work, geopolymeric binder pastes were produced with BA mixed to activators with different alkali contents (expressed as %Na₂O), as well as the incorporation of soluble silicates (Ms content). The production of binary geopolymeric pastes based on the use of two industrial wastes: fluid catalytic cracking (FCC) and aluminum anodizing sludge (AAS), was also assessed. The content in mass of BA/FCC and BA/AAS ranged from 100/0, 90/10; 80/20 and 70/30. Systems with soluble silicates as activator in a molar ratio SiO₂/Na₂O of 1.0 (Ms = 1.0) and Na₂O content of 15%, showed the best results of mechanical strength (42 MPa at day 28^th). The improvement is up to 5X when compared to NaOH based systems. For systems with partial replacement of BA of 10% of AAS and 20% of FCC (80/20), the presence of soluble silicates was also effective to increase compressive strength.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.25 no.1
• /
• pp.51-59
• /
• 2017

In 2014, there were approximately 4,762 fatalities on Korean roads. The fatality rate has decreased by 6.5 %, as compared to that of the previous year. The pedestrian-vehicle fatalities (1,795) have also decreased by 6 % over the previous year. However, the percentage of the pedestrian fatalities has increased from 37.9 % to 38.7 % during the same period. This is why further research is required, even though the KNCAP pedestrian safety assessment and KMVSS for pedestrian protection currently exist. This paper studied the Upper Legform to Bonnet Leading Edge Test at the front of the vehicles, which has not been introduced yet in Korea. The test method and procedure of the new BLE test in the Euro NCAP test protocol have been reviewed, and the physical tests on SUV and sedan with different bonnet leading edge heights have also been conducted and reviewed. In addition, the test results and characteristics have been analyzed via comparison with the former BLE test and each vehicle type.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.6
• /
• pp.31-38
• /
• 2003

It has been recently reported that the presence of sulphate causes abnormal volume changes in lime-stabilized soils. Volume changes in lime-stabilized soils can take place due to sulphate compounds such as ettringite. Sulphate compounds caused a variety of serious geotechnical hazards such as swelling pressure and damages to light structures and pavements. This paper discusses the influence of sulphate on the soil specimens treated with quicklime and chemical additives. The physical and mechanical characteristics were studied by means of laboratory tests. The results showed that the presence of sulphate treated soil reduced the shear strength of the lime treated soils and increased the swelling properties. SEM and XRD results indicated that the presence of sulphate producted needle-like crystals such as ettringite. Moreover, the role of needle-like crystals in specimen was probably related to the swelling properties.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.12 no.1
• /
• pp.55-59
• /
• 2009

As one of the methods for recycling the FRP from the small and medium waste ships, separation of roving layer from the mat has some merits in a sense of the recycling energy and the environmental effects. Similar characteristics, however, between the roving and the mat even with different ratio of the resin and the glass and the thickness of the roving, much thinner than the mat, make the mechanically automatic differentiation difficult. In this study spectrochemical differentiation between the two layers has been made using (1) boiling concentrated sulfuric acid which can dissolve the resin in the FRP layer, (2) methanol and isopropanol solution saturated with KOH which can dissolve the glass, or (3) hydrogen fluoride(HF) solution which can reacts with $SiO_2$ fragments of the glass. Furthermore coloring water-soluble dye following the HF treatment makes the roving layer more distinguishable photo-physically.

• International Journal of Highway Engineering
• /
• v.14 no.1
• /
• pp.17-24
• /
• 2012

This study evaluated the performance of Korean epoxy asphalt mixtures using several laboratory tests. Four types of epoxy asphalt mixtures were manufactured based on 13mm dense graded asphalt mixtures: three Korean and one Japanese epoxy asphalt mixtures where 20% or 40% of asphalt binder was replaced by epoxy resins. Curing time was determined as 3 and 6 hours for the mixtures containing 40% and 20% of epoxy resins, respectively. From the laboratory tests including wheel tracking, indirect tension fatigue, bending beam, and moisture susceptibility tests, it was concluded that the epoxy asphalt mixtures had superior performance than conventional asphalt mixtures except moisture susceptibility. Also, the performance of the Korean epoxy asphalt mixtures was comparable to the Japanese mixtures. Thermal coefficient, bond strength, and indirect tension tests were conducted to examine the applicability of the Korean epoxy asphalt mixtures to concrete repair. Its adhesion was strong enough to be bonded to surrounding concrete materials and its tensile strength was comparable to the concrete, but thermal expansion coefficient was 5 times greater than the surrounding concrete.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.397-400
• /
• 2008

To carry out this study efficiently, the material, physical and mechanical properties of the existing high temperature area was identified and the thermal transportation of structural elements was carried out through the finite element analysis method(ABAQUS) for 40 to 100 MPa high strength concrete based on Fiber Cocktail mixing. The results are as follows. First, it was analyzed that 40, 50 and 60 MPa high strength concretes have a thermal transportation properties similar to the analysis model of 30 MPa normal concrete. Second, it was analyzed that the analysis model of 80 and 100 MPa high strength concrete have slightly lower thermal transportation properties compared to normal model. Third, this study didn't consider the explosive spalling by the pore pressure within high strength concrete. If the properties for the pore pressure within high strength concrete is considered and database by strength and by inner temperature of various high strength concrete and steel materials are established in the future, it is interpreted that the technical foundation will be laid for performance-based design of fire-resistant construction.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.4
• /
• pp.499-505
• /
• 2021

The purpose of this study is to investigate experimentally the physical/chemical properties of concrete surface according to types of formworks. Plywood formwork and coated plywood formwork were prepared. In addition, plywood formwork with sand paper was prepared to simulate deterioration of concrete or rough surface of concrete. Normal concrete was used in this study. The properties of concrete surface were investigated by visual inspection, scanning electron microscopy and energy-dispersive X-ray spectroscopy techniques, elemental mapping, 2D and 3D surface profile measurement, and zeta potential measurement. Test results showed that concrete in a coated formwork had smooth surface and concrete in the formwork with sand paper had rough surface. It was observed that properties of concrete surface depended on types of formworks. Furthermore, differences in surface roughness were significantly higher than those in chemical compositions and zeta potential.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.36 no.3
• /
• pp.535-543
• /
• 2016

This study has been carried out to evaluate the CBR characteristics and the correlations among every soil properties of National road in Yeongnam region. Total of 480 soil samples were collected from 41 administrative districts for more than 30 years. Their physical and mechanical properties such as natural water content, the Atterberg limit, No. 200 sieve passing, the compaction test and the CBR test results were involved. The soils in Yeongnam region, SM, SC, SP and CL by USCS have predominated approximately 79%. The test results show that average CBR values of gravel and sand range from 12.7% to 20.3% and those of silt and clay range from 4.8% to 7.1%. It means that average CBR values of fine grained soils are less than a half of coarse grained one. Natural water content, No. 200 sieve passing, optimum moisture content and maximum dry density of soils are well correlated with CBR values. Especially, it presents that No. 200 sieve passing is the best correlation factor with CBR value. If consider the partition off this region into 6 zones of classified by mother rock, the correlation between CBR value and every soil properties tends to increase. It is suggested that tables, figures and the regressions described in this paper may be available for designers and engineers to understand the characteristics of an embankment materials in Yeongnam region.

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.12
• /
• pp.71-78
• /
• 2011

This paper aims to present the evaluation of engineering characteristics and reusing possibility of waste powders produced in dolomite and limestone nonmetal mining by physical and mechanical experiments on compaction, uniaxial compressive strength, permeability, chemical composition, and so on. Granite soil, 2 types of limestone waste powder, and 1 type of dolomite waste powder were used for main materials, and cement and bentonite were used for admixed materials in this experiments. The findings based on the experimental results are the severe difference of chemical composition of the dolomite & limestone waste powder and the crushed rock waste powder, and the outstanding of engineering characteristics of the dolomite waste powder with high content of MgO compared with the limestone waste powder. The engineering properties on compaction, uniaxial compressive strength, and permeability are enhanced with increase of admixed ratio of waste powder on granite soil. From the experimental results, it can be suggested that the dolomite waste powder admixed with in-situ granite soil is useful as geo-materials with considering of distribution costs.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1996.06a
• /
• pp.5-18
• /
• 1996

The solid state cesium ion source os alumino-silicate based zeolite which contains cerium. The material is an ionic conductor. Cesiums are stably stored in the material and one can extract the cesiums by applying electric field across the electrolyte. Cesium ion bombardment has the unique property of producing high negative ion yield. This ion source is used as the primary source for the production of a negative ion without any gas discharge or the need for a carrier gas. The deposition of materials as an ionic species in the energy range of 1.0 to 300eV is recently recognized as a very promising new thin film technique. This energetic non-thermal equilibrium deposition process produces films by “Kinetic Bonding / Energetic Condensation" mechansim not governed by the common place thermo-mechanical reaction. Under these highly non-equilibrium conditions meta-stable materials are realized and the negative ion is considered to be an optimum paeticle or tool for the purpose. This process differs fundamentally from the conventional ion beam assisted deposition (IBAD) technique such that the ion beam energy transfer to the deposition process is directly coupled the process. Since cesium ion beam sputter deposition process is forming materials with high kinetic energy of metal ion beams, the process provider following unique advantages:(1) to synthesize non thermal-equilibrium materials, (2) to form materials at lower processing temperature than used for conventional chemical of physical vapor deposition, (3) to deposit very uniform, dense, and good adhesive films (4) to make higher doposition rate, (5) to control the ion flux and ion energy independently. Solid state cesium ion beam sputter deposition system has been developed. This source is capable of producing variety of metal ion beams such as C, Si, W, Ta, Mo, Al, Au, Ag, Cr etc. Using this deposition system, several researches have been performed. (1) To produce superior quality amorphous diamond films (2) to produce carbon nitirde hard coatings(Carbon nitride is a new material whose hardness is comparable to the diamond and also has a very high thermal stability.) (3) to produce cesiated amorphous diamond thin film coated Si surface exhibiting negative electron affinity characteristics. In this presentation, the principles of solid state cesium ion beam sputter deposition and several applications of negative metal ion source will be introduced.