• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.5A
• /
• pp.299-305
• /
• 2012

The objective of this paper is to obtain the basic data in order to develop an eco-friendly concrete through evaluation on the properties of polymer cement mortar and concrete using PVAc (Polyvinyl Acetate), as a kind of water-soluble polymer. For this purpose, the physical properties of cement mortar and concrete which does not contain the PVAc as the control batch were compared and analyzed with those using the PVAc. And then, the replacement amount of the PVAc was 3%, 6%, 9% and 12% by binder, respectively. And also, the properties of concrete using the PVAc were evaluated, by adding an antifoaming agent in order to control the air contents increasing with an increase of amount of polymer usage. As a result, in the case of polymer cement mortar using the PVAc, it presented that the compressive strength reduced, while the performance of flexural strength and drying shrinkage increased. When the replacement of the PVAc was 6% within concrete, the compressive, tensile, flexural strength and elastic modulus were increased.

• Journal of the Korean Society of Tobacco Science
• /
• v.6 no.1
• /
• pp.39-49
• /
• 1984

In the tobacco industry, it is important to study the change of mechanical property occurring the expansion process. The purpose of this study is to attain basic data for development of a tobacco expansion method. 1 . Freon gas was adsorbed to tobacco under various conditions of temperature, relative humidity and pressure, and then the amount of freon gas adsorbed was analyzed by GC. Freon adsorption rate of Burley 21 was more than that of By104 at the same condition and about 17 $\pm$ 1% moisture content produced better adsorption rate. 2. Freon adsorbed sample were heated to about $150^{circ}C\;to\;230^{\circ}C$ in a drying oven and recycle duct form about 2 to 30 seconds, and then the change of mechanical property were measured. Heated leaf was damaged when the tissue was pressed by the force of above $0.5x10^8dyn/cm^2$. The optimum condition of no damage of the sample was below the temperature of 15$0^{\circ}C$ and heating time of 10 seconds. It was more economically advantages to treated sample in a recycle duct than to be in a drying oven. By this process, the specific volume of the heated sample was increased from 80 to 110 percent in comparison to that of untreated sample.

• Journal of the Korean Applied Science and Technology
• /
• v.19 no.1
• /
• pp.25-32
• /
• 2002

Two PU flame-retardant coatings, 2,3-DBPO/N-l00 (DBPON) and 2,3-DBPO/IL (DBPOI), were prepared by curing 2,3-dibromo modified polyester (2,3-DBPO) with isocyanate curing agent Desmodur N-l00 (or Desmodur IL) at room temperature. The physical properties and flame-retardancy of the two coatings were tested and compared. As a result, the pot-life, yellowness index, lightness index difference, $60^{\circ}$ specular gloss, cross-hatch adhesion, viscosity, and accelerated weathering resistance of DBPON were better than those of DBPOI; the fineness of grind of the two coatings were the same; and the drying time, hardness, and abrasion resistance of DBPOI were better than those of DBPON. The flame retardancy of the flame-retardant coatings increased with the content of the flame retarding component, 2,3-dibromopropanoic acid (2,3-DBP); and the LOI values of the two coatings were in a range of $27{\sim}29%$ when the content of 2,3-DBP was 30wt%.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.41 no.2
• /
• pp.20-25
• /
• 2009

Many researches are carried out for developing the technology to substitute the surface sizing, although this process improves physical properties and water resistance of paper. This is because surface sizing has fundamental limitation to increase drying energy consumption and to restrict speed of paper machine. However, practical and effective technologies were not developed yet. In this study, we investigated the possibility of the substitution of surface sizing using internal starches, such as cationic starch and oxidized starch. To identify effects of internal starches on physical and optical properties, papers were not only made by adding internal starches into pulp slurry but papers surface sized with oxidized starch were also prepared to compare physical and optical properties. Consequently, tensile strength and internal bond of paper containing internal starches were higher than those of surface sized paper by controlling the type and addition level of cationic starch.

• Advances in concrete construction
• /
• v.7 no.3
• /
• pp.175-181
• /
• 2019

Low-calcium fly ash (LCFA) were used to prepare cement/LCFA specimens in this study. The basic physical properties including water demand, fluidity, setting time, soundness and drying shrinkage of cement/LCFA paste were investigated. The effects of curing time, immersion time and wet-dry cycles in 3% $Na_2SO_4$ solution on the compressive strength and the microstructures of specimens were also discussed. The results show that LCFA increases the water demand, setting time, soundness of cement paste samples. 50% and 60% LCFA replacement ratio decrease the drying shrinkage of hardened cement paste. The compressive strength of plain cement specimens decreases at the later immersion stage in 3% $Na_2SO_4$ solution. The addition of LCFA can decrease this strength reduction of cement specimens. For all specimens with LCFA, the compressive strength increases with increasing immersion time. During the wet-dry cycles, the compressive strength of plain cement specimens decreases with increasing wet-dry cycles. However, the pores in the specimens with 30% and 40% LCFA at early ages could be large enough for the crystal of sodium sulfate, which leads to the compressive strength increase with the increase of wet-dry cycles in 3% $Na_2SO_4$ solution. The microstructures of cement/LCFA specimens are in good agreement with the compressive strength.

• Korean journal of food and cookery science
• /
• v.16 no.1
• /
• pp.47-56
• /
• 2000

The purpose of this study was to develop a drying method of Gangjung. a traditional Korean snack, thus to reduce the drying time and to improve the quality of Gangjung. Two drying methods, hot air drying and far infrared ray drying were used by changing conditions such as air velocity(0.4, 1.2, 1.6 m/s), temperature(40, 50, 60$\^{C}$), and aging. Optimal moisture content of dried Gangjung pellet was 17% which was proper for frying. Cracks appeared on the surface of Gangjung pellet at lower levels of moisture content. Far infrared ray drying saved drying time about 20%. Both hot air drying and far infrared ray drying at 0.4 m/s of air velocity tended to show better quality of Gangjung than those dried at higher air velocities. The expansion volume and texture of Gangjung drying at 40$\^{C}$ was better than other temperature conditions, regardless of drying methods. Quality of Gangjung, dried at single stage without aging, was superior to those dried at double stage including aging process. Moreover, single stage drying save the drying time at least 24 hr. Gangjung dried at high temperature became hard and less brittle in sensory evaluation. In image analysis, air cell distribution in inner structure of Gangjung became uniform and fine as drying temperature decreased to 40$\^{C}$. Overall, Gangjung made of Gangjung pellet by the use of far infrared ray drying at 40$\^{C}$ without aging, showed the best quality in terms of physical and sensory properties.

• Fashion & Textile Research Journal
• /
• v.20 no.5
• /
• pp.600-607
• /
• 2018

Polypropylene fibers, while having many advantages such as light weight, sweat fast drying, water-repellent, drainage, thermal insulation, anti-static property has a drawback in dyeing. In recent years, the development of dyeable polypropylene fibers has expanded its value in the textile market. The purpose of this study is to fabricate composite spun yarns using polypropylene, acrylic, rayon and wool and to analyze tensile properties, uniformity characteristics, bending properties, hairiness, and surface shape according to the degree of fineness and blended ratio. The specimens consisted of 100% polypropylene spun yarn pp30, pp40 and ppa(pp/acrylic), ppr(pp/rayon), ppw(pp/wool), 5 altogether sed in this study. The results of the study are as follows. The breaking strength of polypropylene spun yarn blended with rayon and acrylic was higher than that of 100% polypropylene spun yarn. The polypropylene spun yarn is higher the fineness been shown to decrease the breaking strength and elongation. The bending properties of polypropylene spun yarns were in the order of ppa>ppr>pp40>pp30>ppw. The unevenness of ppw, ppr, and ppa was higher than pp40 and pp30. With the exception of ppw with crimp properties, pp30 and pp40 were found to have a hairiness index greater than ppr, ppa. In the microscopic photographs of polypropylene spun yarn, pp30, which had the highest hairiness index, was found to have a thick yarn and a large number of hairs, and ppw had hairs of 3 mm or more protruding elongated outwardly.

• The Journal of Natural Sciences
• /
• v.8 no.1
• /
• pp.137-143
• /
• 1995

The purpose of this study is to investigate the change of shrinkage, tensile strength, elasticity, light-fastness and color-fastness of 100% cotton upper under wear after acidic treatment and repeated washing and drying. Both of warp and welt were shrinked, especially in the early washing stage. Tensile strength was not weakened by 15 times of repeated washing. Hunter whiteness(HW) of white-underwear decreased, but color difference($\Delta$E) and yellow index(YI) increased corresponding to the frequency of washing and sunlight drying. The discoloration of color-underwear was significant in the early stage.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.6 no.2
• /
• pp.116-121
• /
• 2005

Immobilization technique by PVA encapsulation is an effective alternative for wastewater treatment. However little information is available about the effect of PVA characteristics on physical properties as an encapsulation media. This study aims at investigating the effect of the preparation methods of PVA and filler addition to media on the solubility of PVA. The solubility decreased as the freezing temperature decreased and the vacuum-drying was applied. Addition of the PAC (Powered Activated Carbon) and organoclay decreased the solubility of the PVA gels. Organoclay was more effective for lowering the solubility about 25% than the PAC. Nitrification with the PVA-coating media was less sufficient than with the polyurethane media due to the mass transfer restriction for oxygen and nutrients.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.919-922
• /
• 2008

This paper reports the physical and shrinkage properties of concrete using expansive additive(E) and three shrinkage reducing admixtures(SRA1, 2, 3) in order to reduce shrinkage of concrete. For the properties of fresh concrete, the use of SRA1, 2, 3 results in a increase in fluidity and decrease in the dosage of super plasticizer as much as 0.05$\sim$0.1%. And For the properties of hardened concrete, the use of SRA1, 2, 3 results in a decrease in compressive, tensile and flexural strength slightly. For drying shrinkage properties, the use of SRA3 is the most effective for reduction of shrinkage, and the next best way to reduce shrinkage is combination with expansive additive(E) and shrinkage reducing admixture(SRA) or the using of expansive additive(E).