• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.42 no.2
• /
• pp.163-170
• /
• 2022

The present study investigates NO_x-removal and sound-absorption performances of photocatalytic porous concrete prepared by various TiO₂ application methods. Photocatalytic porous concrete samples were prepared by one of the following: 1) mechanically mixing TiO₂ during casting; 2) mixing bottom ash aggregate pretreated with TiO₂ during casting; and 3) spraying TiO₂ solution to the normally fabricated porous concrete. The test results indicated that the mechanical mixing of TiO₂ decreased the compressive strength as the added TiO₂ content increased. The use of pretreated bottom ash aggregate reduced the porosity, yet the compressive strength of the concrete was similar to that measured from the former method. Porous concrete samples sprayed with the TiO₂ solution exhibited enhanced compressive strength, while the porosity was analogous to those measured from other methods. The NO_x-removal performance was the highest in the samples sprayed with the TiO₂ solution, followed by the samples using pretreated bottom ash aggregate and mechanically mixed TiO₂. The samples with mechanically mixed TiO₂ identified a relationship between soundabsorption performance and porosity. However, no particular tendency was observable in the samples with other TiO₂ application methods.

• Journal of Environmental Health Sciences
• /
• v.30 no.5 s.81
• /
• pp.358-365
• /
• 2004

The photocatalytic oxidation of Rhodamine B(RhB) was studied using photocatalytic reactor filled with module of quartz tube. Module of quartz tube consisted of small quartz tube (inner diameter, 1.5 mm; outer diameter, 3 mm) bundle coated with powder $TiO_2$ and uncoated large quartz tube (inner diameter, 20 mm; outer diameter, 22 mm). Two 30 W germicidal lamp was used as the light source and the reactor volume was 0.5 l. The effects of parameters such as the coating materials and numbers, initial concentration, $H_{2}O_2$ dose and metal deposition (Ag, Pt and Fe) and simultaneous application of $H_{2}O_2$ and metal deposition. The results showed that the initial reaction constant of quartz module coated with powder $TiO_2$ was higher 1.4 time than that of the $TiO_2$ sol and optimum coating number is twice. In order to increase reaction rate, simultaneous application of photocatalytic and photo-fenton reaction using Fe coating and dose $H_{2}O_2$ dose increased reaction rate largely.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.8
• /
• pp.2512-2518
• /
• 2014

The praseodymium-doped $TiO_2$ photocatalyst samples, which could degrade methyl orange under UV irradiation, were prepared by sol-microwave method for improving the photocatalytic activity of $TiO_2$. The resulting materials were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), Transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), Raman spectra, Fourier transform infrared spectra (FTIR) and Ultraviolet-visible diffuse reflectance spectra (UV-vis DRS). It was found Pr doping retarded the growth of crystalline size and the phase transformation from anatase to rutile, and narrowed the band gap energy. Praseodymium doping brought about remarkable improvement in the photoactivity. The optimal dopant amount of Pr was 2% by molar of cement and the calcination temperature was $500^{\circ}C$ for the best photocatalytic activity. The improvement of photocatalytic activity was ascribed to the occurrence of lattice distortion and the effective containment of the recombination of the electron-hole by $Pr^{3+}$.

• Analytical Science and Technology
• /
• v.13 no.5
• /
• pp.646-651
• /
• 2000

The photocatalytic degradation of Mordant Yellow-12 (MY-12) was investigated using a UV-Visible Spectrophotometer and pH meter. The UV-Visible absorbance spectra of the MY-12 contaminated water before and after treatment were presented in figure. The decrease of absorbance occurs at the range of 250 and 450 nm, this result suggests that photocatalytic degradation involves destruction of the aromatic rings in this experiment. More than 32% of the MY-12 was decomposed after one hour in 26-W fluorescent lamp, whereas it was 17% and 24% respectively in 15-W and 21-W lamps. MY-12 was decomposed completely after three hours in 26-W fluorescent lamp. The destruction rate constants were calculated from the change of absorbance and pH.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 1998.11a
• /
• pp.73-74
• /
• 1998

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2001.11a
• /
• pp.23-23
• /
• 2001

• Journal of Korean Society on Water Environment
• /
• v.16 no.4
• /
• pp.445-457
• /
• 2000

This study was carried out comparing with ozone oxidation and photocatalytic degradation for removal of geosmin. In the change of pH, Ozonation, UV-Germicidal lamp and Halogen lamp irradiation and Halogen $lamp/TiO_2$ Powder was very slowly changing, but UV-Germicidal $lamp/TiO_2$ Powder was rapidly changed from 7.0 to 7.7 until 300min of irradiation time, and varied a little after. Geosmin degradation ratio was as following, UV-Germicidal $lamp/TiO_2$ $Powder(200mg/L){\geq}O_3$ > UV-Germicidal $lamp/TiO_2$ $Pw(100mg/L)$ > UV-Germicidal lamp > Halogen lamp. The result of investigation of generated by-products were 3-Heptanone, two sort of aldehydes and three sort of alcohols by ozonation. But It was not generated by photocatalytic degradation.

• Journal of Korean Society for Atmospheric Environment
• /
• v.24 no.1
• /
• pp.91-99
• /
• 2008

A multilayer tower-type photoreactor, in which $TiO_2$-coated glass-tubes were installed, was used to measure the vapor-phase BTEX removal efficiencies by ozone oxidation ($O_3$/UV), photocatalytic oxidation ($TiO_2$/UV) and the combination of ozone and photocatalytic oxidation ($O_3/TiO_2$/UV) process, respectively. The experiments were conducted under various relative humidities, temperatures, ozone concentrations, gas flow rates and BTEX concentrations. As a result, the BTEX removal efficiency and the oxidation rate by $O_3/TiO_2$/UV system were highest, compared to $O_3$/UV and $TiO_2$/UV system. The $O_3/TiO_2$/UV system accelerated the low oxidation rate of low-concentration organic compounds and removed organic compounds to a large extent in a fixed volume of reactor in a short time. Therefore, $O_3/TiO_2$/UV system as a superimposed oxidation technology was developed to efficiently and economically treat refractory VOCs. Also, this study demonstrated feasibility of a technology to scale up a photoreactor from lab-scale to pilot-scale, which uses (i) a separated light-source chamber and a light distribution system, (ii) catalyst fixing to glass-tube media, and (iii) unit connection in series and/or parallel. The experimental results from $O_3/TiO_2$/UV system showed that (i) the highest BTEX removal efficiencies were obtained under relative humidity ranging from 50 to 55% and temperature ranging from 40 to $50^{\circ}C$, and (ii) the removal efficiencies linearly increased with ozone dosage and decreased with gas flow rate. When applying Langmuir-Hinshelwood model to $TiO_2$/UV and $O_3/TiO_2$/UV system, reaction rate constant for $O_3/TiO_2$/UV system was larger than that for $TiO_2$/UV system, however, it was found that adsorption constant for $O_3/TiO_2$/UV system was smaller than that for $TiO_2$/UV system due to competitive adsorption between organics and ozone.

• Food Science and Biotechnology
• /
• v.17 no.6
• /
• pp.1345-1348
• /
• 2008

Titanium dioxide ($TiO_2$) shows antibacterial effects when exposed to near ultra violet (UV) light. In this study, $TiO_2$ photocatalytic continuous reactor was designed and applied to food-borne pathogens such as Vibrio parahaemolyticus ATCC 17802, Salmonella choleraesuis ATCC 14028, and Listeria monocytogenes ATCC 15313. $TiO_2$ films were prepared by conventional sol-gel dip-coating method using titanium tetra iso-propoxide (TTIP). The antibacterial activity of photocatalytic reactor with various flow rates and UV-A illumination time showed effective bactericidal activity. As the UV-A illumination time increased, survival rates of those bacteria decreased. After 60 min of UV-A illumination, the survival rates of V. parahaemolyticus and S. choleraesuis were less than 0.1%. However, that of L. monocytogenes was about 5% at that time point. These results present an effective way to exclude pathogenic bacteria from aqueous foods.

• Journal of Environmental Science International
• /
• v.17 no.2
• /
• pp.171-176
• /
• 2008

The VOCs have a direct influence on indoor air pollution, and stimulate respiratory organs and eyes in human body. Also, most of VOCs are a carcinogenic substances and causes to SBS (sickness building syndrome). Therefore, this study was progressed in photocatalysis of VOCs using UV/$TiO_2$ which was a benign process environmentally. The experiments were performed to know photodegradation characteristics as crystalline structure of $TiO_2$ which had anatase, rutile and P-25 (anatase : rutile = 70 : 30). The main purpose of this study was to identify photocatalytic characteristics as inlet concentration of reactants, $H_2O$, and residence time.