• Polymer(Korea)
• /
• v.36 no.2
• /
• pp.145-148
• /
• 2012

The effects of the linearly polarized UV (LPUV) irradiation and thermal treatment of a photo-degradable polyimide (CBDA-ODA) alignment layer (AL) on its AL properties, liquid crystal (LC) alignment, and LCD characteristics have been investigated. The best quality of LC photo-alignment have been induced by the LPUV-irradiation with much (about 5~10 times) less dosage than that generating the maximum anisotropy of the AL. A thermal treatment of the LPUV-irradiated AL has effectively removed the undesirable, low-M.W. fragments of the AL generated during the photo-decomposition and increased the stability of the AL, which has resulted in improvement of the LC alignment and the LCD property.

• Textile Coloration and Finishing
• /
• v.25 no.3
• /
• pp.172-180
• /
• 2013

Aramid fibers are being used increasingly in a wide range of application due to low density, high specific strength, high modulus, and high thermal resistance. But owing to its special physical and chemical structures, it is sensitive to absorb the ultraviolet light which will degrade the fiber's useful mechanical properties and structure. In this paper, the sol-gel technique was used to improve the photo-stability of p-aramid fibers. $TiO_2$, modified $SiO_2$/$TiO_2$ sol were used as coating solutions. The influence of the such coatings on the photo-stability of p-aramid fiber was investigated by an accelerated photo-ageing method using xenon lamp. The photo-stability of p-aramid fiber showed obvious improvement after the modified silica binding coating. But the amorphous $TiO_2$ sol coatings showed a negative effect. After 144h light exposure, the modified silane binder-coated fibers showed less degradation in mechanical properties with the retained tensile strength greater than about 70% of the original value.

• Nuclear Engineering and Technology
• /
• v.31 no.5
• /
• pp.506-511
• /
• 1999

The pilot system for radioactive liquid laundry waste was developed with treatment capacity, 1ton/hr and set up in the Yong Kwang unit #4. The system is composed of tank module, RO systems and a UV/$H_2O$$_2$photo-oxidation unit. The RO system consists of the BW unit (low-pressure RO for brackish water desalination) and the SW unit (high-pressure RO for seawater desalination). The BW unit possesses 4 RO membranes and it can reduce the feed water volume down to 1/10. This concentrated feed water can be reduced again up to 1/10 in its volume in the SW unit composed of 4 RO membranes. The UV/$H_2O$$_2$ photo-oxidation process unit was used for the detergent degradation. The operation of the pilot system was carried out and verified in its capability through the continuous operation and concentration operation using the actual liquid waste from the power plant. The design criteria and data for industrialization were yielded. The efficiency of the UV/$H_2O$$_2$ photo-oxidation process and the optimum operational procedure were evaluated. The decontamination factors for radioactive cobalt and cesium were measured. This on-site test showed the experimental result in the DF$\geq$300 and volume reduction factor$\geq$100.

• Korean Journal of Materials Research
• /
• v.30 no.6
• /
• pp.279-284
• /
• 2020

In this work, a carbon-doped carbon nitride photocatalyst is successfully synthesized through a simple centrifugal spinning method after heat treatment. The morphology and properties of the prepared photo catalyst are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV-vis spectrophotometer (UV-vis), and specific surface area. The results show that the band gap of the prepared sample, g-CN-10 is 2.1 eV, is significantly lower than that of pure carbon nitride, 2.7 eV. As the amount of cotton candy increased, the absorption capacity of the prepared catalyst for visible light is significantly enhanced. In addition, the degradation efficiency of Rhodamine B (RhB) by sample g-CN-10 is 98.8 % over 2 h, which is twice that value of pure carbon nitride. The enhancement of photocatalytic ability is attributed to the increase of specific surface area after the carbon doping modifies carbon nitride. A possible photocatalytic degradation mechanism of carbon-doped carbon nitride is also suggested.

• Journal of the Korean Ceramic Society
• /
• v.52 no.6
• /
• pp.502-507
• /
• 2015

We examined the photo catalytic activity and catalytic recyclability of CdSe/graphene nanocomposites fabricated via modified hydrothermal technique. The prepared composites were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) with energy dispersive X-ray (EDX), transmission electron microscopy (TEM), Raman spectroscopic analysis, and X-ray photoelectron spectroscopy (XPS). The photocatalytic behavior was investigated through decomposition of RBB as a standard dye under visible light radiation. Our results indicate that there is significant potential for graphene based semiconductor hybrids materials to be used as photocatalysts under visible light irradiation for the degradation of organic dyes from industry effluents.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.191-191
• /
• 2007

By employing a photo-sensitive PVA as a photoresist, we first demonstrated simultaneous patterning and passivation of P3HT active layer. The passivation layers were obtained by annealing the organic layers after developing PVA and over-etching the P3HT layer. The fabricated OTFTs were electrically characterized. The OTFTs after the passivation exhibited the field-effect of ${\sim}5.9{\times}10^{-4}cm^2/V{\cdot}s$, on/off current ratio of ${\sim}10^3$. The value of OTFTs a little degradation with time in air but it appeared different unpassivated OTFT.

• Proceedings of the KSRS Conference
• /
• 2003.11a
• /
• pp.817-819
• /
• 2003

Land degradation is a crucial issue in mountainous areas and is manifested in a variety of processes. For its assessment, application of existing models is not straightforward. In addition, data availability might be a problem. In this paper, a procedure for land degradation assessment is described, which follows a four-step approach: (1) detection, inventory and mapping of land degradation features, (2) assessing the magnitude of soil loss, (3) study of causal factors, and (4) hazard assessment by applying decision trees. This approach is applied to a case study in the Middle Mountain region of Nepal. The study shows that individual mass movement features such as debris slides and slumps can be easily mapped by photo interpretation techniques. Application of soil loss estimation models helps get insight on the magnitude of soil losses. In the study area soil losses are higher in rainfed crops on sloping terraces (highest soil loss is 32 tons/ha/yr) and minimal under dense forest and in irrigated rice fields (less than 1 ton/ha/yr). However there is high frequency of slope failures in the form of slumps in the rice fields. Debris slides are more common on south-facing slopes under rainfed agriculture or in degraded forest. Field evidences and analysis of causal factors for land degradation helps in building decision trees, the use of which for modelling land degradation has the advantage that attributes can be ranked and tested according to their importance. In addition, decision trees are simple to construct, easy to implement and very flexible in adaptations.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1697-1699
• /
• 1996

EPDM compound can be cured with either the sulfur and peroxide based systems. In this study, heat resistance and weatherability of EPDM compounds depending on curing systems were investigated. The test results showed that the peroxide-cured EPDM was more resistant to heat ageing and UV photo-degradation than the sulfur-cured EPDM and it is due to C-C bond is more stable than C-S, S-S bond.

• YAKHAK HOEJI
• /
• v.43 no.6
• /
• pp.703-708
• /
• 1999

The effect of antioxidants on photochemical reaction of pefloxacin by UVB (290~320 nm) was investigated and the possible mechanism of phototoxicity on the skin was also studied. The photo-degradation of pefloxacin by UVB was suppressed by cysteine, reduced glutathione and ascorbic acid, but was promoted by ${\alpha}-tocopherol$. Squalene, accounts for more than 10% of skin surface lipids, was peroxidized by pefloxacin through both radical and singlet oxygen mechanism.

• Journal of Korean Society on Water Environment
• /
• v.29 no.5
• /
• pp.666-673
• /
• 2013

Chloroform is harmful volatile organics and representatives of Trihalomethane (THM). Well-known removal methods of Chloroform are photo oxidation or OH radical oxidation. Plasma on water surface at slightly vacuum condition (45 torr) can produce OH radical and it will help chloroform removal. 81.5% of chloroform is removed by vacuum and plasma in 10 min.. Plasma can totally oxidize it till 2.8% and partially oxidize chloroform up to 18.5%. Water-surface plasma is good method to remove chloroform in short time.