• Journal of the Korean Graphic Arts Communication Society
• /
• v.29 no.2
• /
• pp.83-92
• /
• 2011

A inorganic powder EL lamp was made by screen printing technique with phosphor ink and dielectric ink. The thickness change of a phosphor ink layer and a dielectric ink layer were not influenced on dielectric content, but rely on phosphor size and vehicle. Once finishing screen printing technique with phosphor ink and dielectric ink, and its surface has been printed again before not drying of phosphor ink and dielectric ink. Then phosphor ink and dielectric ink were not transferred. The electric capacity of inorganic powder EL lamp was more influenced on dielectric content than the thickness of dielectric ink layer, and it was more dependent on the thickness of phosphor ink layer than the thickness of dielectric ink layer.

• Journal of the Korean Ceramic Society
• /
• v.41 no.5
• /
• pp.406-409
• /
• 2004

A blue phosphor(ZnS:Cu) is manufactured by solid state reaction for ACPEL(AC powder EL). The effect of artificial defect on phosphor surface on the ZnO phase conversion and resulting luminescence have been studied. It was found that ZnS:Cu could converse to cubic phase more easily due to the formation of artificial defect on 1st fired phosphor by ball-milling process, resulting in improvement of luminescence of phosphor phosphors under the driven EL condition. We found out an optimized ball-mill condition through considering effect of each ball-mill conditions such as milling time and milling rpm on defect. Also we determined relationship between emission luminescence and phase of phosphor based on analyses of crystal structures of phosphors. A significant improvement above 30% was observed in electroluminescence by the artificial defect on ZnS:Cu phosphors compared to non-treated phosphors.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.2
• /
• pp.27-37
• /
• 1997

Photoluminescent and cathodoluminescent charcteristics of inorganic luminescent materials were investigated ot develop possible phosphors for thin film electroluminescent (TFEL) device applications. Mg, Zn, and Photoluminescent and cathodoluminescent charcteristics of inorganic luminescent materials were investigated ot develop possible phosphors for thin film electroluminescent (TFEL) device applications. Mg, Zn, and $Si_3N_4$ powders were used to synthesize $(Mg_xZn_{1-x})SiN_2$ host materials. $Tb_4O_7$ and $Eu_2O_3$ powdrs were added as luminescent centers. Very sharp emission spectra of $Tb^{3+}$ ions were observed from $Mg._5Zn._5SiN_2:Tb$ sampels sintered at $1400^{\circ}C$ for an hour and the maximum intensity of emission spectra occured at wavelength of 550nm (green light). Synthetic conditions of $(Mg_xZn_{1-x})SiN_2:Eu$ phosphors were optimized for the hghest luminescence. The Eu concentrations were varied from 0.2% to 1.6%. Before firing, the powders were mixed using ballmills, methanol, acetone, or D.I. water. The Mg/Zn ratio also were varied from x=0.3 to x=0.7. The maximum PL intensity was obtained from a sample with 1.2% Eu concentration and the powder was mixed with methanol and dried before firing. The maximum intensity of the emission spectra occurred t the wavelength of 470nm(blue light). TFEL devices fabricated by using sputter deposition of $(Mg._3Zn._7)SiN_2:Eu$ phosphor layer showed yellowish white emission at the phosphor field of 2MV/cm.

• Korean Journal of Materials Research
• /
• v.16 no.4
• /
• pp.248-252
• /
• 2006

An investigation is reported on the coating of ZnS:Cu,Cl phosphors by $HfO_2$ using atomic layer deposition method. Hafnium oxide films were prepared at the chamber temperature of $280^{\circ}C$ using $Hf[N(CH_3)_2]_4\;and\;O_2$ as precursors and reactant gas, respectively. XPS and ICP-MS analysis showed the surface composition of coated phosphor powder was hafnium oxide. In FE-SEM analysis, the surface morphology of uncoated phosphors became smoother and clearer as the number of ALD cycle increased from 900 to 1800. The photoluminescence intensity for coated phosphors showed $7.3{\sim}13.4%$ higher than that of uncoated. The effect means that the reactive surface is uniformly coated with stable hafnium oxide to reduce the dead surface layer without change of bulk properties and also its absorptance is almost negligible due to ultrathin(nano-scaled) films. The growth rate is about $1.1{\AA}/cycle$.

• Journal of the Semiconductor & Display Technology
• /
• v.18 no.1
• /
• pp.10-14
• /
• 2019

In this study, we synthesized two $Y_3Al_5O_{12}:Ce^{3+}$ phosphors ($7{\mu}m$-sized and $2{\mu}m$-sized YAG) with different sizes by controlling particles sizes of starting materials of the phosphors for white LED. In the smaller one ($2{\mu}m$-sized YAG), its photoluminescence intensity in the reflective mode was 63 % that of the bigger one ($7{\mu}m$-sized YAG); the quantum efficiencies were 93 % and 70 % for the smaller and the bigger ones. Two kinds of white LED packages with the same color coordinates were fabricated with a blue package (chip size $53{\times}30$) and two phosphors. The luminous flux of the white LED package with the smaller YAG phosphor was 92 % of that with the bigger one, indicating that the quantum efficiency of phosphor dispersed inside LED package was higher than that of the pure powder. It was consistently confirmed by the optical simulation (LightTools 6.3). It is notable according to the optical simulation that the white LED with the smaller phosphor showed 24 % higher luminous efficiency. If the smaller one had the same quantum efficiency as the bigger one (~93 %). Therefore, it can be suggested that the higher luminous efficiency of white LED can be possible by reducing the particle size of the phosphor along with maintaining its similar quantum efficiency.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.29 no.2
• /
• pp.33-44
• /
• 2011

The inorganic powder EL lamp was made by screen printing technique with a phosphor ink and a dielectric ink. The thickness of a phosphor ink layer and a dielectric ink layer is $35{\mu}m$ and $54{\mu}m$ respectively. A increasing ratio of the luminance of inorganic powder EL lamp to be a 1P1PD-phosphor ink layer in which increased voltage at constant frequency is higher 12% than when increased frequency at constant voltage. It is higher 57% than when increased frequency at constant voltage that the rate of increase of the luminance of inorganic powder EL lamp to be a 2PD-phosphor ink layer in which increased voltage at constant frequency. Finally, when increased voltage at constant frequency, a increasing ratio of the luminance of inorganic powder EL lamp to be a 2PD-phosphor ink layer is higher about 40% than that to be a 1P1PD-phosphor ink layer.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.27-32
• /
• 2006

The present status and prospects for further development of thin-film electroluminescent (TFEL) devices using oxide phosphors are described. High-luminance oxide TFEL devices have been recently developed using a new combinatorial deposition technique featuring rf magnetron sputtering with a subdivided powder target. In addition, new flexible oxide TFEL devices have been fabricated on an oxide ceramic sheet and operated stably in air above $200^{\circ}C$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.386-386
• /
• 2012

For white light emitting diode (LED) applications, it has been reported that Y3Al5O12:Ce3+ (YAG:Ce) in nano-sized phosphor performs better than it does in micro-sized particles. This is because nano-sized YAG:Ce can reduce internal light scattering when coated onto a blue LED surface. Recently, there have been many reports on the synthesis of nano-sized YAG particles using bottom-up method, such as co-precipitation method, sol-gel process, hydrothermal method, solvothermal method, and glycothermal method. However, there has been no report using top-down method. Top-down method has advantages than bottom-up method, such as large scale production and easy control of doping concentration and particle size. Therefore, in this study, nano-sized YAG:Ce phosphors were synthesized by a high energy beads milling process with varying beads size, milling time and milling steps. The beads milling process was performed by Laboratory Mill MINICER with ZrO2 beads. The phase identity and morphology of nano-sized YAG:Ce were characterized by X-ray powder diffraction (XRD) and field-emission scanning electron microscopy (FESEM), respectively. By controlling beads size, milling time and milling steps, we synthesized a size-tunable and uniform nano-sized YAG:Ce phosphors which average diameters were 100, 85 and 40 nm, respectively. After milling, there was no impurity and all of the peaks were in good agreement with YAG (JCPDS No. 33-0040). Luminescence and quantum efficiency (QE) of nano-sized YAG:Ce phosphors were measured by fluorescence spectrometer and QE measuring instrument, respectively. The synthesized YAG:Ce absorbed light efficiently in the visible region of 400-500 nm, and showed single broadband emission peaked at 550 nm with 50% of QE. As a result, by considering above results, high energy beads milling process could be a facile and reproducible synthesis method for nano-sized YAG:Ce phosphors.

• Journal of the Korean Society of Radiology
• /
• v.15 no.3
• /
• pp.391-399
• /
• 2021

Eu²⁺ doped polyphosphate NaSr(PO₃)₃ blue-emitting phosphors were synthesized by the conventional solid state method in a reductive atmosphere. The phase formation of NaSr(PO₃)₃ phosphors were characterized by using the X-ray powder diffraction (XRD) measurement. The photoluminescence emission and excitation spectra of the NaSr(PO₃)₃:Eu²⁺ phosphor, and decay curves were measured. Under the near-UV excitation, the phosphor exhibits a band emission around 420 nm assigned to the 4f⁶5d→f7(8S^7/2) transition of Eu²⁺. The temperature dependent emission spectra and decay curves were measured to elevate the thermal properties of the Eu²⁺ doped phosphors. The as-prepared NaSr(PO₃)₃:Eu²⁺ phosphors show a strong temperature dependent performance, which can serve as a promising temperature sensor.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.173-173
• /
• 2009

높은 휘도를 갖는 $Eu^{2+}$가 도핑된 $Sr_3MgSi_2O_8$ 형광체는 고상반응법을 사용하여 합성하였다. 몰 비에 따른 조성을 정밀전자저울을 사용 무게를 칭량하여 에탄올을 용매로 하여 혼합, 건조 후 하소 온도는 $1000^{\circ}C$, 합성 온도는 $1200^{\circ}C$에서 $1400^{\circ}C$까지 $H_2$ 5% Ar 95% 환원분위기에서 소성 온도 별 결정상을 관찰하였고, 그 형태에 따라서는 Powder상태일 때와 Powder를 Press하여 bulk상태로써의 결정상의 변화를 연구하였다. 그 결과 분말상태와 성형을 가한 pellet의 두 가지 형태로 합성하여 비교한 결과 성형공정을 거친 시료의 경우가 분말 상태일 때 보다 좋지 못한 결정상이 관찰되었다. $Sr_3MgSi_2O_8$의 미세구조는 SEM으로 관찰하였다.