• Journal of the Korean Wood Science and Technology
• /
• v.44 no.1
• /
• pp.106-112
• /
• 2016

This study investigated electrical properties and far-infrared ray emission according to the carbonizing temperature and phenol-formaldehyde (PF) resin impregnation ratio of ceramics manufactured using sawdust and rice husk. The far-infrared ray emission values and emission energy values decreased as the carbonizing temperature increased. The far-infrared ray emission values of the ceramics manufactured using a carbonizing process at $600^{\circ}C$ and a board with a PF resin impregnation ratio of 60 percent was 0.930; the emission energy presented the highest value of $4.32{\times}10w/m^2$. The electric resistance decreased as the carbonizing temperature increased. For the increase in the carbonizing temperature above $1200^{\circ}C$, ceramics was very close to a conductor due to the small resistance. The power consumption increased by the decrease of electric resistance and increase of the electric current in the case of a higher resin impregnation ratio.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.3
• /
• pp.360-367
• /
• 2017

This study was carried out to compare the characteristics of low density fiberboards (LDFs) manufactured with different adhesive types such as melamine urea formaldehyde (MUF), phenol formalehyde (PF), emulsified MDI (eMDI) and latexes resins. As results, hard LDFs were successfully manufactured by MUF, PF and eMDI resins. Thermal conductivities of all LDFs were significantly lower than commercial medium density fiberboard. Especially, all LDFs showed comparable thermal insulation performance with extruded polystyrene foam (XPS). LDF manufactured with eMDI resins showed the highest physical properties such as thickness/length swelling by water absorption and bending strength.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.6
• /
• pp.872-882
• /
• 2017

The objective of this study was to evaluate the properties of bamboo oriented strand board (B-OSB) from andong (Gigantochloa psedoarundinacea) and betung (Dendrocalamus asper) with and without steam treatment. Strands were steam-treated at $126^{\circ}C$ for 1 h under 0.14 MPa pressure. The extractive content of bamboo strands before and after steam treatment were determined according to a standard (TAPPI T 204 om-88). Three-layer B-OSB with the core layer perpendicular to the surface and back layers were formed and binded with 8% of phenol formaldehyde (PF) resin with the addition of 1% of wax. The evaluation of physical and mechanical properties of the boards were conducted in accordance with the JIS A 5908:2003 standard. The results showed that steam treatment of bamboo strands significantly reduced the extractive content. Steam treatment tended to increase the dimensional stability and mechanical properties of B-OSB from andong and betung. The results showed that the dimensional stability and bending strength of B-OSB from betung was higher than those of andong. The internal bond strength of B-OSB from andong was higher than betung owing to a greater amount of extractives dissolved during the steam treatment.

• Korean Journal of Materials Research
• /
• v.16 no.5
• /
• pp.302-307
• /
• 2006

The formation and processing of organic insulators on the device performance have been studied in the fabrication of organic thin film transistors (OTFTs). The series of polyvinyls, poly-4-vinyl phenol(PVP) and polyvinyltoluene (PVT), were used as solutes and propylene glycol monomethyl ether acetate(PGMEA) as a solvent in the formation of organic insulators. The cross-linking of organic insulators was also attempted by adding the thermosetting material, poly (melamine-co-formaldehyde) as a hardener in the compound. The electrical characteristics measured in the metal-insulator-metal (MIM) structures showed that insulating properties of PVP layers were generally superior to those of PVT layers. Among the layers of PVP series: PVP(10 wt%) copolymer, 5 wt% cross-linked PVP(10 wt%), PVP(20 wt%) copolymer, 5 wt% cross-linked PVP(20 wt%) and 10 wt% cross-linked PVP(20 wt%), the 10 wt% cross-linked PVP(20 wt%) layer showed the lowest leakage current characteristics. Finally, inverted staggered OTFTs using the PVP(20 wt%) copolymer, 5 wt% cross-linked PVP(20 wt%) and 10 wt% cross-linked PVP(20 wt%) as gate insulators were fabricated on the polyether sulphone (PES) substrates. In our experiments, we could obtain the maximum field effect mobility of 0.31 $cm^2/Vs$ in the device from 5 wt% cross-linked PVP(20 wt%) and the highest on/off current ratio of $1.92{\times}10^5$ in the device from 10 wt% cross-linked PVP(20 wt%).

• Journal of the Semiconductor & Display Technology
• /
• v.5 no.1 s.14
• /
• pp.39-43
• /
• 2006

The polyvinyl series organic films as gate insulators of thin film transistor(TFT) have been processed and characterized on the polyether sulphone (PES) substrates . The poly-4-vinyl phenol(PVP) and polyvinyl toluene (PVT) were used as solutes and propylene glycol monomethyl ether acetate(PGMEA) as a solvent in the formation of organic insulators. The cross-linking of organic insulators was also attempted by adding the thermosetting material, poly (melamine-co-formaldehyde) as a hardener in the compound. The electrical characteristics measured in the metal-insulator-metal (MIM) structures showed that insulating properties of PVP layers were generally superior to those of PVT layers. Among the layers of PVP series; copolymer PVP(10 wt%), 5wt% cross-linked PVP(10 wt%), copolymer PVP(20 wt%), 5 wt% cross-linked PVP(20 wt%) and 10 wt% cross-linked PVP(20 wt%), the 10 wt% cross-linked PVP(20 wt%) layer showed the lowest leakage current of 1.2 pA at ${\pm}10V$. The ms value of surface roughness and the capcitance per unit area are 2.41 and $1.76nF/cm^2$ in the case of 10 wt% cross-linked PVP(20 wt%) layer, respectively.

• Journal of the Korean Wood Science and Technology
• /
• v.33 no.5 s.133
• /
• pp.57-65
• /
• 2005

Following our previous reports for finger-jointed woods with various finger profiles studied for the efficient use of small diameter logs and woods containing various defects, twelve types of finger-jointed woods glued with three kinds of adhesives and with two sizes of finger pitches were made with sitka spruce and red pine. The effects of the adhesives and finger pitches on bending creep performances of finger-jointed woods were investigated. The shape of creep curves differed among the used adhesives and finger pitches of finger-jointed woods for both tested species. Their creep curves showed a linear behavior beyond about one hour, and the N values fitted to power law increased with increasing finger pitches. The initial deformation increased with increasing finger pitches, regardless of the tested species and kinds of adhesives, whereas the effect of finger pitches on the creep deformation was not clear. For finger-jointed woods glued with polyvinyl acetate (PVAc) resin, creep failure occurred in 106 hours after the load was applied. And the difference of the creep compliance between finger-jointed woods glued with resorcinol-phenol formaldehyde (RPF) resin and aqueous vinyl urethane (AVU) resin was small. The ratios for creep performances of finger-jointed woods glued with RPF resin and AVU resin versus solid wood were higher in creep deformation than initial deformation for both species, and the difference between both adhesives was not found. The relative creep decreased with increasing finger pitches, and the marked differences was not found between RPF resin and AVU resin.

• Journal of the Korean Applied Science and Technology
• /
• v.33 no.1
• /
• pp.168-175
• /
• 2016

The surface of glass fiber bundle was modified with functionalized silanes and phenolic resin to improve the tensile strength as well as the adhesion of glass fiber to matrix phenolic resin. The surface modification of reinforcing glass fiber can play a significant role in controlling whole composite characteristics. We applied surface modification of glass fiber with two different functionalized silanes, such as glycidyltrimethoxysilane(G-silane) and aminopropyltriethoxysilane (A-silane), and phenol formaldehyde(PF) resin in one pot or separated process under different coating compositions and temperatures. Thermal treatment temperature is very important factor to improve the mechanical properties of modified glass fiber. Modified glass fiber bundle treated at $170^{\circ}C$ showed the highest tensile strength of $10.05g_f/D$. Surface analyses by scanning electron microscope(SEM) and FT-IR spectroscopy were used to characterize the surface coatings on glass fiber bundles. Mechanical property changes as functions of treatment conditions and coupling agent types were also explained.

• Journal of the Korean Society of Tobacco Science
• /
• v.29 no.1
• /
• pp.30-40
• /
• 2007

The objective of this study was to investigate the contribution of various smoke constituents to the toxicological activity of total particulate matter(TPM) or the gas/vapor phase(GVP). These components included phenol compounds, aromatic amines, polycyclic aromatic hydrocarbons, heterocyclic amines, and carbonyl compounds. The mutagenic and cytotoxic potencies were assessed using the Salmonella mutagenicity assay with S. typimurium TA98 strain and the neutral red uptake cytotoxicity assay(NRU) with BALB/c 3T3 fibroblast cells, respectively. The Salmonella mutagenicity test showed that heterocyclic amines exhibited significantly higher levels of toxicity compared to other smoke constituents. Among them, 2-amino-3,4-dimethylimidazo[4,5-f]quinoline(MeIQ) was shown the most mutagenic compound with a specific mutagenicity of $7.9{\times}10^5\;revertants/{\mu}g$. An analysis of the possible contribution revealed that MeIQ account for only 0.85% of the 2R4F-TPM mutagenicity in TA98. NRU data demonstrated that high cytotoxic activity was obtained for hydroquinone, formaldehyde, and acrolein. Based on the results of the present study, the contribution of acrolein to the cytotoxicity of the GVP fraction was calculated as 61%. Thus, a large proportion of the cytotoxic activity of this complex mixture, cigarette smoke gas phase, can be attributed to the acrolein.

• Journal of the Korean Wood Science and Technology
• /
• v.32 no.6
• /
• pp.57-66
• /
• 2004

To study the efficient usage of small diameter logs and woods containing defects such as knots, slope of the grain and decay, six types of finger-jointed woods with various finger profiles were made of poplar, pine and oak with different density. We investigated the effect of finger profile on static bending strength performances of finger-jointed woods. The efficiency of bending MOE, MOR and deflection showed the highest value in poplar finger-jointed wood with the lowest density of three species, and the lowest value in oak finger-jointed wood with the highest density of three species. The values markedly decreased with increasing finger pitch for finger-jointed wood glued with polyvinyl acetate (PVAc) resin for all tested species, whereas for the finger-jointed wood glued with resorcinol-phenol formaldehyde (RPF) resin, the influence of finger pitch on the efficiency of MOE was not found in all tested species, and those on the efficiency of MOR and deflection indicated the same trend as finger-jointed wood glued with PVAc resin in the case of pine and oak finger-jointed wood with higher densities. It was found that the values tended to decrease with increasing density of species on the whole and the desirable finger pitches were L (6.8 mm) for poplar, M (4.4 mm) for pine and S (3.5 mm) for oak in a view of economy. For finger-jointed wood glued with PVAc resin, the fitness between a tip and a root width of a pair of fingers δ of 0.5 mm indicated the highest efficiency of MOE for all species. And, the influence of δ on MOR was only found in oak finger-jointed wood glued with RPF resin and the desirable δ value for oak was 0.1 mm. However, it was found that the influence of δ on the strength performance was very small.

• Journal of the Korean Wood Science and Technology
• /
• v.32 no.3
• /
• pp.42-51
• /
• 2004

Wood veneer-bamboo zephyr composite board (WBCB) was manufactured to evaluate the properties of bamboo as alternative raw materials for the manufacture of composite panels. Bamboo zephyr was prepared using Moso bamboo (Phyllostachys pubesens Mazel. et Z), Giant timber bamboo (Phyllostachys bambusoides Sieb. et Zucc), and Hachiku bamboo (Phyllostachys nigra var. henosos Stapf). The effect of age and species of bamboo on zephyr production was investigated in terms of the pass number of bamboo split through the rollers, and the width increasing rate of bamboo split. Five-ply WBCBs were produced with Keruing veneers as face and back layers, leading to three layers of bamboo zephyr sheets as core layer. Each layer was placed so that its grain direction was at right angles to that of the adjacent layer and the layers were bonded together with phenol-formaldehyde (PF) resin.The pass number of bamboo split was increased with an increase of the thickness of culm wall. At the same thickness, Moso bamboo showed no effect of the age of bamboo on the pass number. The pass number of split of Giant timber bamboo was lower than that of Moso bamboo. No significant effect of bamboo species and age on the width of zephyr produced was observed. The width of zephyr obtained could be expressed as a function of diameter multiplied by thickness of culm wall. The physical and mechanical properties of WBCB manufactured in all given conditions did not show any significant differences, and they were above the requirement of Korean Standard (KS).