• Progress in Medical Physics
• /
• v.27 no.1
• /
• pp.37-45
• /
• 2016

In proton therapy, in vivo proton beam range verification is very important to deliver conformal dose to the target volume and minimize unnecessary dose to normal tissue. For this purpose, a multi-slit prompt-gamma camera module made of 24 scintillation detectors and 24-channel signal processing system is under development. In the present study, we have developed and tested a dual-mode signal processing system, which can operate in the energy calibration mode and the fast data acquisition mode, to process the signals from the 24 scintillation detectors. As a result of performance test, using the energy calibration mode, we were able to perform energy calibration for the 24 scintillation detectors at the same time and determine the discrimination levels for the detector channels. Further, using the fast data acquisition mode, we were able to measure a prompt-gamma distribution induced by a 45 MeV proton beam. The measured prompt gamma distribution was found similar to the proton dose distribution at the distal fall-off region, and the estimated beam range was $17.13{\pm}0.76mm$, which is close to the proton beam range of 16.15 mm measured by an EBT film.

• Analytical Science and Technology
• /
• v.12 no.2
• /
• pp.125-129
• /
• 1999

Portable-type two electrode system for the determination of highly concentrated hydrogen peroxide (10-75%) has been studied. The electrode body was made with teflon rod (length=10 cm, diameter=1.5 cm) to withstand the highly corrosive power of hydrogen peroxide. Glass carbon rod (diameter=3 mm) was used as the working electrode and a carbon cylinder (i.d.=5 mm; o.d.=9 mm) was used as counter electrode. The applied voltage for the determination of $H_2O_2$ was 0.8 V. Diluting the highly concentrated samples taken from the industrial batch to 10% or less, it was possible to make quantitative determinations, while eliminating the interference from the stabilizer contained in the sample and preventing the surface of the electrode from oxidative corrosion. Employing hydrogen peroxide permeable membrane (teflon membrane${\leq}100{\mu}m$) for the electrode system, it was possible to measure the content of $H_2O_2$ in highly concentrated samples directly, quantitatively and reproducibly with no extra dilution step. However, it was necessary to change the internal electrolyte frequently to maintain the analytical performance of the electrode.

• Analytical Science and Technology
• /
• v.25 no.6
• /
• pp.350-363
• /
• 2012

To determine ionic species in snowpit samples using ion chromatography system, we described the performance of ion chromatography(IC) system, cleaning method of bottle, and interference by filtering procedure. The limit of detection, reproducibilities, and accuracies determined with BCR$^{(R)}$-408 were 0.01-0.26 ${\mu}g$/L, 0.4-17.4%, 4.5-12.0% for cations and 0.02-0.26 ${\mu}g/L$, 0.1-27.6%, 1.3-5.6% for anions, respectively. Lab blank test for sample bottle indicated that $CH_3CO_2{^-}$, $HCO_2{^-}$, and $NH_4{^+}$ can be easily contaminated in the lab environment. The positive interferences of $NO_3{^-}$ were partly attributed to the cleaning method of bottle. The filtering of melted snow sample should be carefully applied because it can positively affect the concentration levels of some ionic species. Finally, this method was applied to measure ionic species in snowpit samples from the upward area near NEEM camp and the uncertainties of measurement data of $F^-$ were also estimated.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.29 no.5
• /
• pp.427-435
• /
• 2009

Cylindrical structures such as pipes and shafts are widely used in various industrial facilities. Recently, researches on magnetostrictive transduction of torsional waves have been actively reported for the nondestructive evaluation of those cylindrical structures. However, the existing magnetostrictive patch transducer has somewhat inconvenient and time.consuming process like patch bonding to a structure since it should employ a magnetostrictive patch having strong magnetostriction. To overcome these limitations of the existing transducer, in this work, we develop a novel modular magnetostrictive transducer to generate and measure torsional waves to inspect a cylindrical structure. The proposed transducer can be applied as viscous liquid coupling with shear couplant or dry coupling without coupling media instead of patch bonding to a structure. We describe a detailed structure of the modular transducer and conduct some experiments to verify its performance.

• Tunnel and Underground Space
• /
• v.10 no.4
• /
• pp.526-532
• /
• 2000

The uniaxial compressive strength of rock mass is known as the major factor in the assessment of drillability and the optimum excavation design in full-face tunnel excavation by TBM. Referring to worldwide cases, TBM has been applied mostly to the rock mass within the strength range of 80~250 MPa. Recently, a water way tunnel has been constructed as a part of Milyang dam project by TBM within the rock masses where the rock type is mainly granite with some granophyre, hornfels and andesite. Their uniaxial compressive strengths in extended area are estimated higher than 260 MPa. In this paper, the relation between the penetration rate and the rock mass properties is analyzed and TBM application to the very hard rocks is discussed. As a result that three suggestions to predict the TBM net penetration rate are analyzed, NTH method seems a better approach than other methods in the extremely hard rocks. NTH prediction matches with the results of actual values with the variations of 2~20%. Hardness measurement by Schmidt hammer and RMR estimation are carried out along the L = 5.3 km entire TBM tunnel alignment. The net penetration rate measured monthly is shown to be reciprocally proportional to Schmidt rebound hardness and RMR where coefficients of correlation, $R^2$are 0.705 and 0.777 respectively. As a result, they are good quantitative indices for the prediction of TBM net penetration rate in the extremely hard rocks. Magnitude of in-situ stress has a certain effect on TBM performance, and it is required to measure the in-situ stresses in TBM excavation design.

• Journal of Technology Innovation
• /
• v.19 no.1
• /
• pp.1-27
• /
• 2011

This paper aims to measure and analyze R&D productivities and efficiencies of 17 major OECD countries including Korea over the 1984-2008 period by using the Malmquist Productivity Index and Data Envelopment Analysis, classifying R&D performance into an output and outcome aspects. It also searches the Korea's current status and characteristics in each R&D stage to enhance Total Factor Productivity (TFP) compared with other developed countries. Our major findings are the followings: (i) Korea's productivity index of R&D input vis-a-vis R&D output is very high (13.39% annual growth rate) compared with those of major advanced countries, whereas the annual average of efficiency index is very low (0.33), i.e. Korea's technical efficiency index has risen to 0.83 at the last time series started at 0.10 point and come up to the level of major advanced countries. (ii) the Korea's productivity index of R&D output vis-a-vis R&D outcome is very low (14.02% annual reduction rate) compared with those of major advanced countries, whereas the annual average of efficiency index is very high (0.22), i.e. Korea's integrated frontier technical efficiency index has dropped to 0.057 at the last time series started at 1.00 point and coming up to the level of major advanced countries. (iii) The productivity of R&D input vis-a-vis R&D outcome is positively correlated with that of R&D output vis-a-vis R&D outcome and the growth of R&D input factors. In a nutshell, it implicates that the effort to take advantage of R&D outputs, namely establishing the diffusion and commercialization system of technical knowledge to the level of developed countries, should be strengthened over that on the growth of R&D investment and output for enhancing R&D productivity and efficiency in Korea.

• Journal of Intelligence and Information Systems
• /
• v.8 no.1
• /
• pp.119-139
• /
• 2002

In electronic catalogs, each item is represented as an independent unit while the parts of the item can be composed of a higher level of functionality. Thus, the search for this kind of product database is limited to the retrieval of most similar standard commodities. However, many industrial products need to configure optional parts to fulfill the required specifications. Since there are many paths in finding the required specifications, we need to develop a search system via the configuration process. In this system, we adopt a two-phased approach. The first phase finds the most similar template, and the second phase adjusts the template specifications toward the required set of specifications by the Constraint and Rule Satisfaction Problem approach. There is no guarantee that the most similar template can find the most desirable configuration. The search system needs backtracking capability, so the search can stop at a satisfied local optimal satisfaction. This framework is applied to the configuration of computers and peripherals. Template-based reasoning is basically the same as case-based reasoning. The required set of specifications is represented by a list of criteria, and matched with the product specifications to find the closest ones. To measure the distance, we develop a thesaurus of values, which can identify the meaning of numbers, symbols, and words. With this configuration, the performance of the search by configuration algorithm is evaluated in terms of feasibility and admissibility.

• Journal of KIISE
• /
• v.41 no.11
• /
• pp.943-957
• /
• 2014

Removing noise, called denoising, is an essential factor for the more intuitive and more accurate results in boundary image matching. This paper deals with a partial denoising problem that tries to allow a limited amount of partial noise embedded in boundary images. To solve this problem, we first define partial denoising time-series which can be generated from an original image time-series by removing a variety of partial noises and propose an efficient mechanism that quickly obtains those partial denoising time-series in the time-series domain rather than the image domain. We next present the partial denoising distance, which is the minimum distance from a query time-series to all possible partial denoising time-series generated from a data time-series, and we use this partial denoising distance as a similarity measure in boundary image matching. Using the partial denoising distance, however, incurs a severe computational overhead since there are a large number of partial denoising time-series to be considered. To solve this problem, we derive a tight lower bound for the partial denoising distance and formally prove its correctness. We also propose range and k-NN search algorithms exploiting the partial denoising distance in boundary image matching. Through extensive experiments, we finally show that our lower bound-based approach improves search performance by up to an order of magnitude in partial denoising-based boundary image matching.

• The KIPS Transactions:PartD
• /
• v.10D no.5
• /
• pp.793-804
• /
• 2003

In the latest, it's increasing an applied technology to be related with growth of industry circles. It's one of them a software to be used in industry circles. and It's most important part to apply an industrial equipment, so software to take charge of major part is indicative performance of quipment. At this time, it's inspired an evaluation and measurement of software quality to have within industrial equipment, and it's forming the research and development by the inside and outside of the country. For this, it's constructed a valuation metric to be based on ISO/IEC 12119, the International Standard for general the terms desired of quality of software and ISO/IEC 9126-2, the International Standard of the terms valuation of qualify for evaluation and measure, and for this accomplishment, It has been designed and developed industrial software international standard compatible approval system which approve a quality based on quality test result of industrial software using the ISO/IEC 14598-6 that international standard for organization of evaluation module.

• Journal of KIISE:Software and Applications
• /
• v.30 no.1_2
• /
• pp.153-163
• /
• 2003

In this paper, we propose a new technique of image based rendering(IBR) for the pose transformation of a face by using only a frontal face image and its mesh without a three-dimensional model. To substitute the 3D geometric model, first, we make up a standard mesh set of a certain person for several face sides ; front. left, right, half-left and half-right sides. For the given person, we compose only the frontal mesh of the frontal face image to be transformed. The other mesh is automatically generated based on the standard mesh set. And then, the frontal face image is geometrically transformed to give different view by using Invertible Meshwarp Algorithm, which is improved to tolerate the overlap or inversion of neighbor vertexes in the mesh. The same warping algorithm is used to generate the opening or closing effect of both eyes and a mouth. To evaluate the transformation performance, we capture dynamic images from 10 persons rotating their heads horizontally. And we measure the location error of 14 main features between the corresponding original and transformed facial images. That is, the average difference is calculated between the distances from the center of both eyes to each feature point for the corresponding original and transformed images. As a result, the average error in feature location is about 7.0% of the distance from the center of both eyes to the center of a mouth.