• 제목/요약/키워드: percent C

검색결과 1,601건 처리시간 0.028초

왕겨 연소기(燃燒機)를 이용(利用)한 온수(溫水)보일러 시스템 개발(開發) (I) -실험적(實驗的) 연구(硏究)- (Development of a Hot Water Boiler System with a Rice Hull Furnace)

  • 이용국;박승제;백풍기;노상하
    • Journal of Biosystems Engineering
    • /
    • 제12권4호
    • /
    • pp.31-43
    • /
    • 1987
  • This study was performed to develop a hot water boiler system with small scale automatic rice hull furnace for the multi-purpose use in the farm. For the experiment a prototype hot water boiler system with rice hull furnace was fabricated, which was equipped with automatic hull feeder, igniter and ash removal device. Optimum operational conditions of the prototype: system were analyzed. The results arc summarized as follows. 1. The temperature measured right above the burning surface should be higher than $500^{\circ}C$ combustion. 2. The top zone of the combustion chamber was the most suitable location of the thermocouple to pick up the control temperature for the automatic operation of the rice hull furnace. 3. The content of carbon monoxide in the flue gas was increased with the filling height of burning material but it was less than 0.3 percent in volume in this experiment. When the filling height was expressed as the ratio of rice hull feed rate to the volume of the combustion chamber above the burning surface, the optimum ratio was about $150kg/m^3-h$. 4. The combustion efficiency of the prototype was higher than 95 percent when the feed rate was 1.1 to 2.3 kg/h and moisture content of rice hull was 22.4 percent (w.b.) or less. 5. It was estimated that the optimum operational conditions of the system were 1.3 to 2.0 kg/h in feed rate, 70 to 100 percent in excess air and 500 to $510^{\circ}C$ in control temperature. 6. The efficiency of coil heal exchanger increased with a decrease in feed rate of rice hull. When the rice hull feed rates were 1.1, 1.7 and 2.3 kg/h, the efficiencies of coil heat exchanger were about 34, 30 and 25 percent and heat transfer rates were 5.7, 7.6 and 8.8 MJ/h, respectively. When the flat plate heat exchanger was used in addition to the coil heat exchanger, the efficiency of the heat exchanger system increased to 48 percent.

  • PDF

양송이 균사(菌絲) 생장(生長)과 자실체(子實體) 수량(收量)에 미치는 몇가지 환경요인(環境要園)의 영향(影響) (Effects of Some Environmental Factors on the Mycelial Growth and Mushroom Yield of Agaricus bisporus)

  • 차동열;박종성;신관철
    • 한국균학회지
    • /
    • 제9권1호
    • /
    • pp.7-12
    • /
    • 1981
  • 앙송이 복토후(覆土後) 재배실온도(栽培室溫度), $CO_{2}$ 및 복토수분함량(覆土水分含量)이 복토층(覆土層)의 균사생장(菌絲生長) 및 자실체(子實體) 형성(形成)과 수량(收量)에 미치는 영향(影響)에 관(關)하여 연구(硏究)한 결과(結果)는 다음과 같다. 1. 복토후(覆土後) 균사(菌絲)의 영양생장(營養生長) 기문중(期聞中) 재배실온도(栽培室溫度)는 $30^{\circ}C$일때 균사생장(菌絲生長)이 가장 빠르고 25, 20, $15^{\circ}C$로 온도(溫度)가 낮아질수록 감소(減少)하였다. 자실체(子實體)의 형성(形成)및 수량(收量)은 $52^{\circ}C$에서 최대(最大)였고 온도(溫度)가 그보다 높거나 낮으면 감소(減少)하는 경향(傾向)이었다. 2. 복토(覆土)의 수분함량(水分含量)은 70%일 때 균사생장(菌絲生長)이 가장 빠르고 수분함량(水分含量)의 감소(減少)에 비례(比例)하여 감소(減少)하였다. 자실체(子責體)의 형성(形成) 및 수량(收量)은 균사생장최적수분함량(菌絲生長最適水分含量)보다 낮은 60%구(區)에서 최대(最大)였다. 3. 복토후(覆土後) 7일간(日間)의$CO_{2}$농도(濃度)가 0.16%일때는 균사생장(菌絲生長) 및 자실체(子實體)의 형성(形成)이 양호(良好)하였으나 $0.5%{\sim}2.0%$에서는 균사생장(菌絲生長)과 자실체형성(子實體形成)이 급감(急減)하였다. 4. 자실체(子叢體)의 개체중량(個體重量)은 재배실온도(栽培室溫度) $20^{\circ}C$, 복토수분(覆土水分) 70%에서 최대(最大)였다.

  • PDF

신생아 패혈증의 다양한 선별검사들의 진단적 가치 (Diagnostic value of various screening tests in neonatal sepsis)

  • 제현곤;정영미;정수진
    • Clinical and Experimental Pediatrics
    • /
    • 제49권11호
    • /
    • pp.1167-1173
    • /
    • 2006
  • 목 적 : 신생아 패혈증을 진단하기 위해 단독 그리고 복합적인 다양한 선별검사를 분석하기 위해 일신기독병원의 신생아집중치료실에서 2001년 4월 1일부터 2005년 12월 31일까지 68개월 동안 시행했다. 방 법 : 패혈증의 임상증상이 있는 100명의 신생아와 증상이 없는 정상 신생아를 대상으로 연구를 시행했다. 신생아 패혈증의 진단을 위해 CRP, 총 백혈구 수, 총 호중구 수, 미숙호중구/총호중구 비(I/T비), 혈소판 수, 호중구의 변성, 다형 핵 백혈구에 대한 GAC를 사용했다. 결 과 : CRP는 A군에서는 50례 중 40례에서(86%) 양성이었고 B군에서는 50례 중 37례에서(74%) 양성이었으며 특이도는 94%였다. 총 호중구 수는 민감도와 특이도가 각각 A군에서는 72%와 86%였고 B군에서는 62%와 86%로 단일 검사상 민감도가 두 번째로 높았다. A군에서 GAC와 혈소판 수에 대한 각각의 민감도는 74%와 64%였다. A군과 B군에 대해 검사를 개별적으로 시행했을 경우와 함께 시행했을 경우에 대한 민감도, 특이도, 그리고 예측도를 계산했다. 결 론 : CRP, 총 백혈구 수, 총 호중구 수, 혈소판 수, 호중구의 변성과 다형 핵 백혈구에 대한 GAC는 신생아 패혈증이 없는 배양 검사 상 음성인 경우를 알아내는데 높은 민감도를 나타냈다. 더욱이 3가지 검사를 함께 시행할 경우에 민감도가 증가했다.

흙댐의 다짐밀도가 안정도에 미치는 영향에 관한 연구 (A Study on the Effect of the Compaction Density on the Stability of Earth Dam)

  • 윤충섭;김시원
    • 한국농공학회지
    • /
    • 제31권1호
    • /
    • pp.82-95
    • /
    • 1989
  • This study was carried out for the stability analysis of earth dam by the variation of compaction density. The test samples were taken from five kinds of soil used for banking material and the degree of compaction for this samples were chosen 100, 95, 90, 85, and 80 percent. The stability problems were analysed by the settlement and camber( extra banking) of dam, strength parameter and dam slope, and coefficient of permeability and seapage flow through dam body. The results of the stability analysis of earth dam are as follows. 1. The more the fine particle increases and lower the compaction degree becomes, the lower the preconsolidation load becomes but the compression index becomes higher. 2. Sixty to eighty percent of settlement of dam occurs during the construction period and the settlement ratio after completion of dam is inversly proportional to the degree of compaction. 3. The camber of dam has heigher value in condition that it has more fine particle(N) and heigher dam height(H) with the relation of H= e(aN-bH-e). 4. The cohesion(C) decreases in proportion to compaction degree(D) and fine particle(N) with the relation of C= aD+ bN-c, but the internal friction angle is almost constant regardless of change of degree of compaction. 5. In fine soil, strength parameter from triaxial compression test is smaller than that from direct shear test but, they are almost same in coarse soil regardless of the test method. 6. The safety factor of the dam slope generally decreases in proportion to cohesion and degree of compaction but, in case of coarse soil, it is less related to the degree of compaction and is mainly afected by internal friction angle. 7. Soil permeability(K) decreases by the increases of the degree of compaction and fine particle with relation of K=e(a-bl)-cN) 8. The more compaction thickness is, the less vertical permeability (Kv) is but the more h6rzontal permeability (KH) is, and ratio of Kv versus KH is largest in range from 85 to 90 percent of degree of corn paction. 9. With the compaction more than 85 percent and coefficient of permeability less than ${\alpha}$X 10-$^3$cm/sec, the earth dam is generally safe from the piping action.

  • PDF

Identification of Novel SNPs with Effect on Economic Traits in Uncoupling Protein Gene of Korean Native Chicken

  • Oh, J.D.;Kong, H.S.;Lee, J.H.;Choi, I.S.;Lee, S.J.;Lee, S.G.;Sang, B.D.;Choi, C.H.;Cho, B.W.;Jeon, G.J.;Lee, H.K.
    • Asian-Australasian Journal of Animal Sciences
    • /
    • 제19권8호
    • /
    • pp.1065-1070
    • /
    • 2006
  • The avian uncoupling protein (avUCP) is a member of the mitochondrial transporter superfamily that uncouples proton entry in the mitochondrial matrix from ATP synthesis. The sequencing analysis method was used to identify nucleotide polymorphisms within the avUCP gene in Korean native chicken (KNC). This study identified ten single nucleotide polymorphisms (SNPs) in the avUCP gene. We analyzed the SNPs of the avUCP gene to investigate whether polymorphism in the gene might be responsible for quantitative variations in economic traits in KNC. Three significant polymorphic sites for economic traits were avUCP C+282T (mean body weight, p<0.05), avUCP C+433T (daily percent lay, p<0.05), and avUCP T+1316C (daily percent lay, p<0.05). The frequency of each SNP was 0.125 (C+282T in avUCP gene exon 1 region), 0.150 (C+433T in avUCP gene intron 1 region), and 0.15 (T+1316C in avUCP gene exon 3 region), respectively. Among the identified SNPs, one pair of SNPs (genotype CC, C+282T and TT, avUCP C+433T) showed the highest daily percent lay (p<0.05) and mean body weight (p<0.05) and the frequency was 0.067. This study of the avUCP gene could be useful for genetic studies of this gene and selection on economic traits for KNC.

한국청소년의 성실태고찰 (Implication for Korean Adolescent Sexuality)

  • 홍문식
    • 보건교육건강증진학회지
    • /
    • 제6권1호
    • /
    • pp.22-33
    • /
    • 1989
  • Rapid socio-cultural and economic changes in the country has brought with it changes in the society's value system. For a traditional society that is increasingly being exposed to modernization but where sex norms are still very restrictive, the adolescent sexual mores takes on added significance. Adolescents are caught between two opposing forces, the changing environment that allows for freer and liberal mores and the traditional society that cannot keep pace with the changing environment and therefore demands resistance to changes. This paper focuses on problems of adolescent sexuality in this country and considers the countermeasures for the existing problems. Amongst the problems are: (a) increasingly younger age of the adolescents who start sexual intercourse (b) non-use of contraception, (c) unwanted pregnancies, (d) increase in the number of induced abortion and (e) increase in the number of unwanted children and unmarried mothers. The Korean adolescent's sexual behavior seems to follow that of the developed countries. In other words, many western modes of life and sexual values seem to bave been copied in Korea and yet Korean adolescents lack in their knowledge of sex related matters such as reproductive physiology and contraception. Among middle and high school students, female students are reported to have less knowledge on sex than male students according to a 1988 survey by KIPH. Even among the unmarried famale factory workers, only 42.5 percent replied they know of the condom, and 25.1 percent and 23.1 percent said they had knowledge of spermicide and menstrual regulation respectively. However, 14.9 percent and 13.9 percent reported that they had a knowledge of the loop and female sterilization respectively according to the 1984 study by KIPH. Among the middle school students 0.8 percent said they had experience in sexual intercourse, while 7.3 percent of the high school students reported having had sexual intercourse. The sexual intercourse experience rate among the unmarried female factory workers is 37.8 percent. Among those female factory workers with sexual experience, 46.7 percent had more than one sex partners. Only 39.1 percent of male students and 18.9 percent of female students among those with sexual intercourse experience have used contraceptives. mostly condoms and oral pills 45.1 percent of female factory workers with sexual intercourse experience used contraceptives such as pills, condoms and rhythm methods. The pregnancy experience rate among the female factory workers who had experience in sexual intercourse is 29.5 percent, which is 11.1 percent among the total respondents. Out of the 102 pregnant female workers, 98 workers(96.1 percent) terminated their pregnancy by induced abortion and 2 workders(2 percent) in natural abortion, while 1 worker(1 percent) was in pregnancy and another 1 worker had normal birth that was subsequently sent to orphanage. In order to cope with the problem of adolescent sexuality, a drastic and strong policy measures should be taken by the government. The most effective countermeasure to the adolescent sexual problems appears to the education. The sex and population education in the school is very much in need. In addition, sex education program through mass media and at the job sit-should be promoted for a healthy development of adolescents' sexual behavior. Also, the existing national family planning program, which has focused on the married couples, should be extended to the unmarried people in its scope and contents of the program.

  • PDF

폴리에치렌 글리콜-400에 의한 목재(木材)의 칫수안정화(安定化) (On the dimensional stabilization of woods with treatment of Polyethylene Glycol-400)

  • 조남석;조재명;배규용
    • Journal of the Korean Wood Science and Technology
    • /
    • 제3권1호
    • /
    • pp.3-15
    • /
    • 1975
  • How to stabilize wood against shrinking and swelling in variable atmospheric moisture conditions is important to the wood-using industry and a challenge to research. Polyethylene glycol stabilize wood by bulking the fiber. PEG also serve as a chemical seasoning agent, suppress decay in high concentrations, and have slight effect on physical properties, gluing or finishing. The study designed to determine the effect of PEG-400 on the dimensional stabilization of local hardwoods for wood carvings that could supply a greatly expanding tourist trade and making curved furniture parts, lamp stands and other decorative objects, and possible gunstock. The species examined were 6 species, Seo-Namoo (Carpinus laxiflora), Cheungcheung-Namoo (Cornus controversa), Gorosae-Namoo (Acer mono), Karae-Namoo (Juglans mandshurica), Jolcham-Namoo (Quercusserrata) and Sanbud-Namoo (Prunus sargentii), used as block of 5cm thick radially to the grain, 7cm wide tangentially, and 70cm long parallel to the wood grain. All these test piecies were conditioned above the fiber saturation point before impregnation. The stabilization effects were determined for PEG-400 treated woods in a 50 percent solution for 20 days. The following conclusions were obtained. PEG retentions increased with treating time. It was more effective to treat at 60$^{\circ}C$ than at room temperature. In degree of PEG-400 impregnation on species, Cheungcheung-Namoo havinglow specific gravity had the highest retentions, 68.77% but the lowest, 56.33% was shown in Jolcham-Namoo with high specific gravity. Specific gravity of treated wood increased considerably with effectiveness of polymer loading. The increases in specific gravity were 5.36 to 13.16 percent. The highest was Jolcham-Namoo, the lowest Karae-Namoo. On the dimensional stability, a 40 percent of effectiveness of polymer loading was just as effective as 60 percent in reduction in water absorptivity (RWA), antishrinkage efficiency (ASE) and antiswelling efficiency (AE), and from over 60 percent they increased more rapidly. Also species response varied considerably. ASE was 30.12 to 69.97 percent tangentially and 27.86 to 56.37 percent radially, AE 34.06 to 73.76 percent tangentially and 30.11 to 70.12 percent radially, and RWA 42.31 to 65.32 percent. No differences in volume swelling among the 6 species were observed. Its values were ranged from 14.98 to 19.55 percent and also increased with PEG retentions. On the mechanical properties, the strengths very much decreased with PEG-400 loadings as shown in Figure 12; that were 11.41 to 22.90 percent in compression, 21.61 to 34.35 percent in bending and 22.83 to 36.83 percent in tensile strength. PEG retention in cell wall was less than 1 percent and the most of PEG were immersed in cell lumen. Except for Korae-Namoo, effectivenesses of polymer loading were as much high as 61.58 to 75.02 percent. This is believed to be due to the effect of PEG-400 on excellant dimensional stability of treated woods.

  • PDF

통일계(統一系) 수도품종(水稻品種)의 저온장해(低溫障害)에 관(關)한 연구(硏究) (Studies on the Low Temperature Injury of the Rice Varieties)

  • 최창렬;김문규;조재성;김충수
    • 농업과학연구
    • /
    • 제4권1호
    • /
    • pp.10-20
    • /
    • 1977
  • $Indica{\times}Japonica$형(型) 수도품종(水稻品種)의 저온발아성(低溫發芽性)과 유묘기(幼苗期)의 저온(低溫)에 의(依)한 장해(障害)를 구명(究明)하기 위(爲)하여 유일외(流一外)29개(個)의 품종(品種)을 $10^{\circ}C$$15^{\circ}C$ 등(等)에서 발아시험(發芽試驗)하는 한편 유일외(流一外)5개(個) 품종(品種)을 15일간(日間) pot하여 재배(栽培)하여 $5^{\circ}C$$15^{\circ}C$에서 각각처리(各各處理)한 15 일(日) 후(後)에 모의 생육(生育) 조사(調査)하였던 바 그 결과(結果)를 요약(要約)하면 다음과 같다. 1. $10^{\circ}C$에서는 이리(裡里) 323호(號), (水原) 253호(號), 이리(裡里) 325호(號), 밀양(密陽) 22호(號), 수원(水原) 251호(號) 및 수원(水原) 267호(號)등 품종(品種)은 70% 이상(以上)의 발아율(發芽率)을 보였고, 도도로끼와세, 밀양(密陽) 23호(號), 유신(維新), 이리(裡里) 328호(號) 및 이리(裡里) 329호(號)등 품종(品種)은 10% 이하(以下)의 낮은 발아율(發芽率)을 보였다. 2. $15^{\circ}C$에서는 수원(水原) 262호(號)는 100%의 발아율(發芽率)을 보였으며, 밀양(密陽) 22호(號), 도도로끼와세, 유일(流一), 밀양(密陽) 29호(號) 수원(水原) 258호(號), 밀양(密陽) 23호(號), 밀양(密陽) 24호(號), 밀양(密陽) 28호(號) 및 밀양(密陽) 21호(號)등 품종(品種)은 90% 이상(以上)의 높은 발아율(發芽率)을 보였던 반면(反面) 이리(裡里) 328호(號), 이리(裡里) 329호(號), 진흥(振興) 및 미네히까리 등 품종(品種)은 50% 이하(以下)의 낮은 발아율(發芽率)을 보였다. 3. 발아율(發芽率)과 평균발아(平均發芽) 일수(日數)를 감안(勘案)할 때 밀양(密陽)22호(號) 및 이리(裡里) 323호(號)가 저온발아성(低溫發芽性)이 높은 품종(品種)이라고 보겠으며 $Indica{\times}Japonica$형(型) 품종(品種)의 저온아성(低溫芽性) 정도(程度)는 Japonica형(型) 품종(品種)들에 비(比)해 반드시 낮지 않았다. 4. $1^{\circ}C$에서 유묘(幼苗)가 6시간(時間)은 노출(露出)되어 있어도 생육(生育)에 거의 영향(影響)을 받지 않았으며 12시간(時間) 노출(露出)되었을 경우(境遇) 품종(品種)에 따라 잎이 시드는 경향(傾向)을 보였으나 다시 정당온도(正堂溫度)를 유지(維持)할 경우(境遇) 회복(回復)되었다. 유묘(幼苗)가 저온(低溫)에 노출(露出)되었을 경우(境遇) 잎이 시드는 정도(程度)는 Japonica형(型) 품종(品種)인 밀양(密陽) 15호(號)가 $Indica{\times}Japonica$형(型) 품종군(品種群)에 비(比)현저(顯著)히 낮았다. 5. 조생유일(早生幼一), 유일(幼一) 및 유신(維新)의 유묘(幼苗)는 $1^{\circ}C$에서 36시간(時間) 처리(處理)되었을 경우(境遇) 70% 그리고 72시간(時間) 처리(處理)에서는 100% 고사(枯死)하였으며 약온처리(藥溫處理)에서도 75% 이상(以上) 고사(枯死)하였던 반면(反面) 밀양(密陽) 15호(號)는 72시간(時間) 처리(處理)되었을 경우(境遇) 65%의 고사율(枯死率)을 보였다. 6. 공시(供試)된 전체품종(全體品種)은 24시간(時間) 내지 36시간(時間) 처리(處理)에서 지상부(地上部) 및 지하부(地下部) 생육(生育)의 현저(顯著)한 감퇴(減退)를 보였고 감퇴정도(減退程度)는 처리시간(處理時間)이 길어짐에 따라 현저(顯著)히 심(甚)하였다.

  • PDF

산업관련표(産業關聯表)에 의(依)한 임업구조분석(林業構造分析)과 유발생산액(誘發生産額) -임업(林業)이 한국경제(韓國經濟)에 미치는 영향(影響)- (Analysis of Forestry Structure and Induced Output Based on Input - output Table - Influences of Forestry Production on Korean Economy -)

  • 이승윤
    • Journal of the Korean Wood Science and Technology
    • /
    • 제2권4호
    • /
    • pp.4-14
    • /
    • 1974
  • The total forest land area in Korea accounts for some 67 percent of the nation's land total. Its productivity, however, is very low. Consequently, forest production accounts for only about 2 percent of the gross national product and a minor proportion of no more than about 5 percent versus primary industry. In this case, however, only the direct income from forestry is taken into account, making no reference to the forestry output induced by other industrial sectors. The value added Or the induced forestry output in manufacturing the primary wood products into higher quality products, makes a larger contribution to the economy than direct contribution. So, this author has tried to analyze the structure of forestry and compute the repercussion effect and the induced output of primary forest products when utilized by other industries for their raw materials, Hsing the input-output table and attached tables for 1963 and 1966 issued by the Bank of Korea. 1. Analysis of forestry structure A. Changes in total output Durng the nine-year period, 1961-1969, the real gross national product in Korea increased 2.1 times, while that of primary industries went up about 1. 4 times. Forestry which was valued at 9,380 million won in 1961, was picked up about 2. 1 times to 20, 120 million won in 1969. The rate of the forestry income in the GNP, accordingly, was no more than 1.5 percent both in 1961 and 1962, whereas its rate in primary industries increased 3.5 to 5.4 percent. Such increase in forestry income is attributable to increased forest production and rise in timber prices. The rate of forestry income, nonetheless, was on the decrease on a gradual basis. B. Changes in input coefficient The input coefficient which indicates the inputs of the forest products into other sectors were up in general in 1966 over 1963. It is noted that the input coefficient indicating the amount of forest products supplied to such industries closely related with forestry as lumber and plywood, and wood products and furniture, showed a downward trend for the period 1963-1966. On the other hand, the forest input into other sectors was generally on the increase. Meanwhile, the input coefficient representing the yolume of the forest products supplied to the forestry sector itself showed an upward tendency, which meant more and more decrease in input from other sectors. Generally speaking, in direct proportion to the higher input coefficient in any industrial sector, the reinput coefficient which denotes the use of its products by the same sector becomes higher and higher. C. Changes in ratio of intermediate input The intermediate input ratio showing the dependency on raw materials went up to 15.43 percent m 1966 from 11. 37 percent in 1963. The dependency of forestry on raw materials was no more than 15.43 percent, accounting for a high 83.57 percent of value added. If the intermediate input ratio increases in any given sector, the input coefficient which represents the fe-use of its products by the same sector becomes large. D. Changes in the ratio of intermediate demand The ratio of the intermediate demand represents the characteristics of the intermediary production in each industry, the intermediate demand ratio in forestry which accunted for 69.7 percent in 1963 went up to 75.2 percent in 1966. In other words, forestry is a remarkable industry in that there is characteristics of the intermediary production. E. Changes in import coefficient The import coefficient which denotes the relation between the production activities and imports, recorded at 4.4 percent in 1963, decreased to 2.4 percent in 1966. The ratio of import to total output is not so high. F. Changes in market composition of imported goods One of the major imported goods in the forestry sector is lumber. The import value increased by 60 percent to 667 million won in 1966 from 407 million won in 1963. The sales of imported forest products to two major outlets-lumber and plywood, and wood products and furniture-increased to 343 million won and 31 million won in 1966 from 240million won and 30 million won in 1963 respectively. On the other hand, imported goods valued at 66 million won were sold to the paper products sector in 1963; however, no supply to this sector was recorded in 1963. Besides these major markets, primary industries such as the fishery, coal and agriculture sectors purchase materials from forestry. 2. Analysis of repercussion effect on production The repercussion effect of final demand in any given sector upon the expansion of the production of other sectors was analyzed, using the inverse matrix coefficient tables attached to the the I.O. Table. A. Changes in intra-sector transaction value of inverse matrix coefficient. The intra-sector transaction value of an inverse matrix coefficient represents the extent of an induced increase in the production of self-support products of the same sector, when it is generated directly and indirectly by one unit of final demand in any given sector. The intra-sector transaction value of the forestry sector rose from 1.04 in 1963 to 1, 11 in 1966. It may well be said, therefore, that forestry induces much more self-supporting products in the production of one unit of final demand for forest products. B. Changes in column total of inverse matrix coefficient It should be noted that the column total indicates the degree of effect of the output of the corresponding and related sectors generated by one unit of final demand in each sector. No changes in the column total of the forestry sector were recorded between the 1963 and 1966 figures, both being the same 1. 19. C. Changes in difference between column total and intra-sector transaction amount. The difference between the column total and intra-sector transaction amount by sector reveals the extent of effect of output of related industrial sector induced indirectly by one unit of final demand in corresponding sector. This change in forestry dropped remarkable to 0.08 in 1966 from 0.15 in 1963. Accordingly, the effect of inducement of indirect output of other forestry-related sectors has decreased; this is a really natural phenomenon, as compared with an increasing input coefficient generated by the re-use of forest products by the forestry sector. 3. Induced output of forestry A. Forest products, wood in particular, are supplied to other industries as their raw materials, increasng their value added. In this connection the primary dependency rate on forestry for 1963 and 1966 was compared, i. e., an increase or decrease in each sector, from 7.71 percent in 1963 to 11.91 percent in 1966 in agriculture, 10.32 to 6.11 in fishery, 16.24 to 19.90 in mining, 0.76 to 0.70 in the manufacturing sector and 2.79 to 4.77 percent in the construction sector. Generally speaking, on the average the dependency on forestry during the period 1963-1966 increased from 5.92 percent to 8.03 percent. Accordingly, it may easily be known that the primary forestry output induced by primary and secondary industries increased from 16, 109 million won in 1963 to 48, 842 million won in 1966. B. The forest products are supplied to other industries as their raw materials. The products are processed further into higher quality products. thus indirectly increasing the value of the forest products. The ratio of the increased value added or the secondary dependency on forestry for 1963 and 1966 showed an increase or decrease, from 5.98 percent to 7.87 percent in agriculture, 9.06 to 5.74 in fishery, 13.56 to 15.81 in mining, 0.68 to 0.61 in the manufacturing sector and 2.71 to 4.54 in the construction sector. The average ratio in this connection increased from 4.69 percent to 5.60 percent. In the meantime, the secondary forestry output induced by primary and secondary industries rose from 12,779 million Wall in 1963 to 34,084 million won in 1966. C. The dependency of tertiary industries on forestry showed very minor ratios of 0.46 percent and 0.04 percent in 1963 and 1966 respectively. The forestry output induced by tertiary industry also decreased from 685 million won to 123 million won during the same period. D. Generally speaking, the ratio of dependency on forestry increased from 17.68 percent in 1963 to 24.28 percent in 1966 in primary industries, from 4.69 percent to 5.70 percent in secondary industries, while, as mentioned above, the ratio in the case of tertiary industry decreased from 0.46 to 0.04 percent during the period 1963-66. The mining industry reveals the heaviest rate of dependency on forestry with 29.80 percent in 1963 and 35.71 percent in 1966. As it result, the direct forestry income, valued at 8,172 million won in 1963, shot up to 22,724 million won in 1966. Its composition ratio lo the national income rose from 1.9 percent in 1963 to 2.3 per cent in 1966. If the induced outcome is taken into account, the total forestry production which was estimated at 37,744 million won in 1963 picked up to 105,773 million won in 1966, about 4.5 times its direct income. It is further noted that the ratio of the gross forestry product to the gross national product. rose significantly from 8.8 percent in 1963 to 10.7 percent in 1966. E. In computing the above mentioned ratio not taken into consideration were such intangible, indirect effects as the drought and flood prevention, check of soil run-off, watershed and land conservation, improvement of the people's recreational and emotional living, and maintenance and increase in the national health and sanitation. F. In conclusion, I would like to emphasize that the forestry sector exercices an important effect upon the national economy and that the effect of induced forestry output is greater than its direct income.

  • PDF

증기전처리(蒸氣前處理)가 상수리나무판재(版材)의 건조속도(乾燥速度)와 건조결함(乾燥缺陷)에 미치는 영향(影響) (Effect of Presteaming on the Drying Rate and Drying Defects of Quercus acutissima)

  • 이형우;정희석
    • Journal of the Korean Wood Science and Technology
    • /
    • 제13권2호
    • /
    • pp.3-13
    • /
    • 1985
  • 본(本) 연구(硏究)는 증기전처리(蒸氣前處理)가 두께 3 cm인 상수리나무 (Quercus acutissima)의 건조속도(乾燥速度)와 건조결함(乾燥缺陷)에 미치는 영향을 알고자 하였다. 생재상태(生材狀態)의 전처리용(前處理用) 판재(板材)를 $100^{\circ}C$의 온도(溫度)에서 4시간동안 증기전처리(蒸氣前處理)한 후 무처리판재(無處理板材)와 함께 Rasmusse이 제시한 건조(乾燥)스케쥴 ($T_4-C_2$)을 사용하여 합수율(合水率) 10%까지 열기건조(熱氣乾燥)하였다. 그 결과(結果)는 다음과 같았다. 평균(平均) 건조속도(乾燥速度)는 무처리판재(無處理板材)의 경우 2.51%/일(日)이고 증기전처리판재(蒸氣前處理板材)의 경우 3.08%/일(日)였으며, 증기전처리(蒸氣前處理)로 함수율(含水率) 70%에서 10%까지의 건조시간(乾燥時間)을 약 18% 감소(減少)시켰다. 표면할열(表面割裂)에 대한 증기전처리(蒸氣前處理)의 효과(效果)는 거의 없었으나 횡단면할열(橫斷面割裂)에 있어서는 증기전처리판재(蒸氣前處理板材)가 무처리판재(無處理板材)에 비해 감소(減少)되었다. 증기전처리판재(蒸氣前處理板材)의 내부할열(內部割裂), 너비굽음 및 찌그러짐의 발생율(發生率)이 무처리판재(無處理板材)보다 약간씩 낮았다. 건조재(乾燥材)의 품등(品等)도 증기전처리판재(蒸氣前處理板材)가 무처리판재(無處理板材)보다 양호(良好)하여 1등급(等級)의 출현율(出現率)이 20% 높았으며, 2등급(等級)은 15%, 3등급(等級)은 5%씩 그 출현율(出現率)이 낮았다.

  • PDF