• Proceedings of the KWS Conference
• /
• 2000.10a
• /
• pp.78-80
• /
• 2000

• Proceedings of the KWS Conference
• /
• 2006.10a
• /
• pp.83-85
• /
• 2006

• Proceedings of the KWS Conference
• /
• 1997.10a
• /
• pp.239-241
• /
• 1997

• Proceedings of the KWS Conference
• /
• 1996.10a
• /
• pp.66-69
• /
• 1996

• Journal of Welding and Joining
• /
• v.26 no.1
• /
• pp.69-75
• /
• 2008

Spot welding which use the main process for side block production of stainless steel railway vehicle is legged behind in laser welding about a quality and productivity. Although the laser welding has many potential advantages such as low heat input and aspect ratio of weld bead, its application to a new structural component still is required many engineering data including mechanical properties such as tensile, fatigue strength, etc on. Therefore, experimental analysis was carried out to understand the fatigue phenomena of different thickness stainless steel overlap joining panels by Nd:YAG laser welding. The fatigue life curves were obtained through fatigue tests with the various levels of applied load. The fatigue life is related with the parameters such as gap size and penetration depth through experiment. As the results, tensile strength and fatigue life were proportional in heat input level and gap was identified the major factor for fatigue life. Also we could know that deferent a-ferrite content at HAZ depend on welding heat input was important factor to determine a formation of initial crack and total fatigue life cycle.

• Laser Solutions
• /
• v.12 no.3
• /
• pp.14-17
• /
• 2009

The laser welding was performed for the flange joint of two overlapped coaxial circular pipes which serve as the inlet and connector pipes of STS 316L. The laser welding test finally resulted in a good penetration depth of 1.8 to 2.0 mm. On the way to get the good welding quality, two important parameters were found to be optimized. One is the focal positioning which is the offset of the laser beam focus to the exact welding seam line, which is more critical in the inner flange laser welding. When the beam spot size was deviated more than $200\;{\mu}m$ from the seam line, welding of two pipes is failed. The other is a gap size since a certain amount of gap is inevitable due to fabrication tolerance, or artificial allowances for smooth insertion of a pipe. However, it is required to restrict the gap allowance within 0.2mm to avoid undesirable undercut on a welding bead.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.2
• /
• pp.310-316
• /
• 2003

One of the significant subject in the automatic arc welding is to establish control system of the welding parameters for controlling bead geometry as a criterion to evaluate the quality of arc welding. This paper proposes an inference algorithm for bead geometry in CMA Welding using Neuro-Fuzzy algorithm. The characteristic welding parameters are measured by the circuit composed of hall sensor, voltage divider tachometer, etc. and then the bead geometry of each weld pool is calculated and detected by an image processing with CCD camera and a measuring with microscope. The relationships between the characteristic welding parameters and the bead geometry have been arranged empirically. From the result of experiments, membership functions and fuzzy rules are tuned and determined by the learning of neural network, and then the relationship between actual bead geometry and inferred bead geometry are concluded by fuzzy logic controller. In the applied inference system of bead geometry using Neuro-Fuzzy algorithm, the inference error percent is within -5%∼+4% in case of bead width, -10%∼+10% in bead height, -5%∼+6% in bead area, -10%∼+10% in penetration. Use of the Neuro-Fuzzy algorithm allows the CMA Welding system to evaluate the quality in bead geometry in real time as the welding parameters change.

• Journal of Welding and Joining
• /
• v.30 no.5
• /
• pp.70-75
• /
• 2012

This study is related to the laser weldability of AZ31B magnesium alloy, an all-purpose wrought alloy with good strength and ductility. In general, AZ31B is classified into AZ31B-H24 and AZ31B-O depending on temper designation. Thus, in this study, the laser weldability of AZ31B-H24 and AZ31B-O was investigated and compared. CW Nd:YAG laser was used to produce bead and butt joints. And the effects of welding conditions on the weldability of these joints were examined in detail. As a result of this study, AZ31B-H24 was found to have thinner oxide film and smaller grain size compared with AZ31B-O. Due to such difference, in bead welding, AZ31B-H24 had more wide welding range for full penetration compared with AZ31B-O. Furthermore, it was also confirmed that AZ31B-H24 and AZ31B-O have different welding conditions to obtain stable keyhole in butt welding.

• International Journal of Korean Welding Society
• /
• v.2 no.2
• /
• pp.26-31
• /
• 2002

Considering the fuel consumption of car, a light structure of aluminum alloys is desired fer car body nowadays. However, fusion welding of aluminum alloys has some problems of reduction of joint efficiency, porosity formation and hot cracking. In the present work, investigation to improve the joint performance of laser welded joint has been carried out by addition of Cu, Ni, and Zr to A6NO 1 alloy welds. Aluminum alloy plate of 2.Omm in thickness with filler metal bar was welded by twin beam Nd: YAG laser facility (total power: 5kW). The filler metals were prepared by changing the chemical compositions for adding the elements into the weld metal. Thirteen filler metal bars were prepared and pre-placed into the base metal before welding. Ar gas shielding with a flow rate of 10 1/min was used. The defocusing distance is kept at 0 mm. At travel speeds off 3 to 9 and at laser power of 5kW (front beam 2kW rear beam 3kW), full penetration welds were obtained, whereas at travel speeds of 12 to 18 m/min and same power, partial penetration was observed. The joint efficiency of laser-welded joint was improved by the addition of Cu, Ni, and Zr due to the solid solution hardening, grain refining and precipitation hardening. The type of hardening has been further considered by metallurgical examination.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.7-7
• /
• 2009

TIG 용접에서는 후판 용접의 경우 용입의 한계 때문에 깊고 넓은 그루브 가공을 하여 다층 용접을 한다. 이 때, 그루브를 채우는 용착금속에 의한 응고 수축과 과대한 입열로 인한 변형이 문제시 되고 있다. 변형을 줄이기 위해서는 용착금속의 양과 입열량을 줄여야 한다. 이러한 문제를 해결하기 위해 그루브의 루트패이스를 두껍게 하고 그루브각을 줄여서 용착량을 줄인다. 이때, 좁은 그루브에서 두꺼운 루트패이스를 완전 용입할 수 있는 용접 프로세스가 필요하다. 비드가 좁고 깊은 용입 특성을 가지는 Plasma welding(PAW) 경우에는 좁은 그루브 속에 토치가 접근하기 어려워 적용하기 어렵다. 따라서 접근성이 용이한 TIG 용접에서 높은 용입형상비를 가지는 용접공정 개발이 필요하다. 선행연구로 높은 용입 형상비를 가지는 Active flux Tungsten Inert Gas(ATIG) 용접이 연구되었다. ATIG의 용입 증가 메커니즘으로는 Marangoni effect, 음이온들로 인한 아크 수축 효과, 절연 플럭스에 의한 아크 수축효과 등으로 알려져 있다. 또한 선행연구에서 ATIG에서 Ar가스에 He 또는 $H_2$ 가스를 첨가하면 용입이 더욱 증가하는 것을 확인하였다. 본 연구에서는 A-TIG에 He 가스를 적용하고 아크길이 0.5mm, 1.0mm, 2.0mm와 전극 선단각 30도, 60도, 90도에 따른 용입 형상비와 변형량을 검토하기 위해 실험을 하였다. 실험 결과는 아크길이가 감소할수록 전극 선단각이 증가할수록 용입 형상비는 증가하였고, 변형량은 감소하였다.