• Composites Research
• /
• v.35 no.6
• /
• pp.469-476
• /
• 2022

In this paper, the microwave absorbing characteristics after the impact of the radar-absorbing structure (RAS) consisting of periodic pattern sheet (PPS) and glass fiber-reinforced plastic (GFRP) were experimentally investigated. The fabricated RAS effectively absorbed the microwave in the X-band (8.2-12.4 GHz). In order to induce the damage to the RAS, a low-velocity impact test with various impact energy of 15, 40, and 60 J was conducted. Afterward, the impact damage was observed by using visual inspection, non-destructive test, and image processing method. Moreover, the absorbing performance of intact and damaged RAS was measured by the free-space measurement system. The experiment results revealed that the delamination damage from the impact energy of 15 J did not considerably affect the microwave absorbing performance of the RAS. However, fiber breakage and penetration damage with a relatively large damaged area were occuured when the impact energy was increased up to 40 J and 60 J, and these failures significantly degraded the microwave absorbing characteristics of the RAS.

• Journal of Pharmaceutical Investigation
• /
• v.32 no.2
• /
• pp.87-93
• /
• 2002

This study is to enhance drug penetration via skin and investigate anti-inflammation effect following adoption of ultrasound. For this goal gel containing triamcinolone was prepared and the skin penetration rate and the change effects of blood plasma ingredients and serum enzyme were investigated. Using Franz type diffusion cell and the skin of hairless mouse, the permeation enhancing effect of ultrasound was tested. After the injury by direct trauma, the blood test was performed by measuring WBC, lymphocyte, and neutrophyl, and by analyzing CPK and LDH. The ultrasound transducer whose technical specification is geometric area(GA) $1.4\;cm^2$, effective radiation area(ERA) $0.8\;cm^2$, and beam non-uniformity ratio(BNR) 6.0 max was used. The influence of frequency having an effect on skin permeation rate was higher in the case of using 1MHz and continuous treatment. The temperature of receptor phase was not influenced in skin permeation by phonophoresis. Skin permeation increase attended by intensity of ultrasound, the permeation of triamcinolone was accelerated at $2.5\;w/cm^2\;than\;1.0\;w/cm^2$. Following muscle injury phonophoretic group the number of WBC, neutrophil and lympholyte were decreased significantly as compared with both control group and ultrasound group. The result of variation of serum CPK and LDH activity conformed to the phonophoretic effect as same pattern with the variation of WBC, neutrophil and lymphocyte.

• The Journal of Korean Physical Therapy
• /
• v.22 no.6
• /
• pp.77-83
• /
• 2010

Purpose: The aim of this study was to do numerical analysis of the wavelength dependence in low level laser therapy (LLLT) using a finite element method (FEM). Methods: Numerical analysis of heat transfer based on a Pennes' bioheat equation was performed to assess the wavelength dependence of effects of LLLT in a single layer and in multilayered tissue that consists of skin, fat and muscle. The three different wavelengths selected, 660 nm, 830 nm and 980 nm, were ones that are frequently used in clinic settings for the therapy of musculoskeletal disorders. Laser parameters were set to the power density of 35.7 W/$cm^2$, a spot diameter of 0.06 cm, and a laser exposure time of 50 seconds for all wavelengths. Results: Temperature changes in tissue based on a heat transfer equation using a finite element method were simulated and were dominantly dependent upon the absorption coefficient of each tissue layer. In the analysis of a single tissue layer, heat generation by fixed laser exposure at each wavelength had a similar pattern for increasing temperature in both skin and fat (980 nm > 660 nm > 830 nm), but in the muscle layer 660nm generated the most heat (660 nm ${\gg}$ 980 nm > 830 nm). The heat generation in multilayered tissue versus penetration depth was shown that the temperature of 660 nm wavelength was higher than those of 830 nm and 980 nm Conclusion: Numerical analysis of heat transfer versus penetration depth using a finite element method showed that the greatest amount of heat generation is seen in multilayered tissue at = 660 nm. Numerical analysis of heat transfer may help lend insight into thermal events occurring inside tissue layers during low level laser therapy.

• Korean Journal of Bronchoesophagology
• /
• v.19 no.1
• /
• pp.19-24
• /
• 2013

Objective The objective was to evaluate changes in swallow safety and dietary status after the transcutaneous injection of botulinum toxin into the upper esophageal sphincter in a series of outpatients with dysphagia. Methods Patients who were at risk for aspiration and who had an unsuccessful trial of swallowing therapy were admitted to the study. All patients showed significant pooling of fluids in the pyriform sinus. All patients were treated in the office; none had previous esophageal dilatation. The upper border of the cricoid cartilage was identified using standard electromyogram procedures and botulinum toxin was injected. Outcomes were assessed using the penetration-aspiration scale, NIH swallowiwng safety score, patients' short-term and long-term subjective impressions of their ability to swallow, and change in dietary status. Results Ten patients underwent an instrumental evaluation of swallowing function. Of the 10 patients, 9 showed an overall improvement in their ability to take an oral diet safely. The penetration-aspiration scale, NIH swallowiwng safety score, patients' short-term and long-term subjective impressions of their ability to swallow, and change in dietary status were significantly improved after office-based botox injection. Conclusion Office-based EMG guided botox injection to the cricopharyngeus muscle is a simple, safe, and effective tool for dysphagia patients. Injection of Botox in the office should be considered when the dysphagia pattern is aspiration after swallow.

• Korean journal of applied entomology
• /
• v.48 no.2
• /
• pp.171-178
• /
• 2009

The changes of feeding pattern and the amount of insecticide penetrated into the leaf were monitored for 420 min after treatment of three concentrations of dinotefuran. At about 30 min after treatment of insecticide, the overall feeding pattern in EPG (Electrical Penetration Graph) monitoring was started to change, and there was significant difference in proportions of NP (non-penetration), PA (pathway activity), and phloem-feeding patterns among the different concentrations of dinotefuran treatment. Especially, as the amount of insecticide penetrated into a leaf increased, the reactive behaviors against this insecticide such as withdrawal of proboscis and movements of stylet of aphid were more quickly exhibited. And also, total time at which the proboscis of the aphids did not penetrate the plant was getting longer. The amount of dinotefuran penetrated into a leaf was monitored with HPLC. When the recommended concentration (100 mg/L) of the insecticide was treated, 5.24${\sim}$7.24 mg/L of the insecticide was detected from the leaf, and the proboscis of the aphids was apparently withdrawn from the leaf at approximately 60 minutes after treatment of this insecticide.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.10
• /
• pp.393-405
• /
• 2020

Various geotechnical information is required to evaluate the stability of the ground and a foundation once liquefaction occurs due to earthquakes, such as the soil strength and groundwater level. The results of the Standard Penetration Test (SPT) conducted in Korea are registered in the National Geotechnical Information Portal System. If geotechnical information for a non-drilled area is needed, geostatistics can be applied. This paper is about the feasibility of obtaining ground information by the Empirical Bayesian Kriging (EBK) method and the Inverse Distance Weighting Method (IDWM). Esri's ArcGIS Pro program was used to estimate these techniques. The soil strength parameter of the drilling area and the level of groundwater obtained from the standard penetration test were cross-validated with the results of the analysis technique. In addition, Multichannel Analysis of Surface Waves (MASW) was conducted to verify the techniques used in the analysis. The Buk-gu area of Pohang was divided into 1.0 km×1.0 km and 110 zones. The cross-validation for the SPT N value and groundwater level through EBK and IDWM showed that both techniques were suitable. MASW presented an approximate section area, making it difficult to clearly grasp the distribution pattern and groundwater level of the SPT N value.

• Korean journal of applied entomology
• /
• v.44 no.4 s.141
• /
• pp.271-276
• /
• 2005

To investigate feeding behaviour of the greenpeach aphid (Myzus persicae) on several plants, DC electrical penetration graph (EPG) technique was used. We chose 5 plants including pepper, melon, cabbage, radish, and eggplant which were known as major host Plants of this species. This study was focused whether feeding patterns of the aphid were different and which plants would be the most preferable among 5 host plants. The time from initial proboscis contact with a each leaf until the first electrical contact, as a measure of the time taken for the stylet penetration, the time from electrical contact to the first potential drop as a time consumed until intracellular sampling, the number of potential drops per an hour during periods of regular intercellular pathway probing, and the time from electrical contact to tile first phloem specific pattern indicating the time taken to reach and attempt to feed upon the phloem were analysed. As a result, except the number of potential drop, there was no significant differency of feeding patterns among 5 plants. However, the feeding patterns related on host acceptability were observed more frequently from Pepper, radish, and e99r1an1 than melon and cabbage.

• Korean Journal of Food Science and Technology
• /
• v.16 no.2
• /
• pp.206-210
• /
• 1984

Heat penetration pattern of canned oyster mushroom(Pleurotus astreatus) was monitored for processing variables-can size, heating temperature and solid fill fraction, and its effects on sterilization condition was reviewed. The $f_h$ value decreased sharply with decrease of solid fill fraction and then became stable from certain solid fill fraction unique to can size. Heat penetration was a little faster at higher heating temperature with lower $f_h$ value. As viewed from $f_h$ value, convection started at higher solid fill fraction with higher length/diameter ratio, and $f_h$ values decreased to about 1.0 with decrease of solid fill fraction. From standpoint of overall cost, retorting time and energy consumption, solid fill fraction of 3/5 was optimum for all can sizes considered.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.31 no.6
• /
• pp.282-286
• /
• 2021

Penetration depth and compressive residual stress of laser-carburized TiZrN coating by thickness of carbon paste were investigated in terms of carbon potential. The carbon paste was covered with a thickness of 1.1 mm using screen printing, and applied to a thickness of 0.4 mm using spin coating, and laser carburization was performed under the same conditions. As the thickness of carbon paste increased, the diffraction pattern of the laser-carburized TiZrN coating shifted to a lower angle, indicating solid solution strengthening and lattice distortion. For microstructure analysis using TEM, the defects and carbon concentration of the laser-carburized TiZrN coating increased as the carbon paste was thicker. It indicated that the variation of the carbon potential corresponds to the change in the paste thickness. In XPS depth profile analysis, high concentration of carbon and formation of carbide were observed in laser-carburized TiZrN coating with thick carbon paste. It revealed that the carbon concentration on the surface and carbon potential were changed by the thickness control of carbon paste. The compressive residual stress increased from 3.67 GPa to 4.58 GPa by the variation of carbon concentration.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.8
• /
• pp.387-391
• /
• 2006

The Ag photodoping effect in amorphous $As_{40}Ge_{10}Se_{15}S_{35}$ chalcogenide thin films for holographic recording has been investigated using a He-Ne laser (${\lambda}$=632.8 nm). The chalcogenide films thickness prepared in the present work were thinner in comparison with the penetration depth of recording light ($d_p=1.66{\mu}m$). It exhibits a tendency of the variation of the diffraction efficiency (${\eta}$) in amorphous chalcogende films, independently of the Ag photodoping. That is, ${\eta}$ increases rapidly at the beginning of the recording process and reaches the maximum (${\eta}_{max}$) and slowly decreases slowly with the exposed time. In addition, the value of ${\eta}_{max}$ depends strongly on chalcogenide film thickness(d) and its maximum peak among the films with d = 40, 80, 150, 300, and 633 nm is observed 0.083% at d = 150 nm (approximately 1/2 ${\Delta}n$), where ${\Delta}$n is the refractive index of chalcogenide thin film (${\Delta}n=2.0$). The ${\eta}$ is largely enhanced by Ag photodoping into the chakogenides. In particular, the value of ${\eta}_{max}$ in a bilayer of 10-nm-thick Ag/150-nm-thick $As_{40}Ge_{10}Se_{15}S_{35}$ film is about 1.6%, which corresponds to ${\sim}20$ times larger than that of the single-layer $As_{40}Ge_{10}Se_{15}S_{35}$ thin film (without Ag). And we obtained the diffraction pattern according to the formation of (P:P) polarization holographic grating using Mask pattern and SLM.