• Journal of Hydrogen and New Energy
• /
• v.29 no.6
• /
• pp.606-619
• /
• 2018

This study focuses on the performance of hydrogen energy based hybrid system in terms of system reliability of electricity generation. With this aim to evaluate the off-grid system of photovoltaic (PV), wind turbine, electrolyzer, fuelcell, $H_2$ tank and storage batteries, 14 different sites in South Korea are simulated using HOMER. Performance analysis includes simulation on the different sites, verification of operational behaviors on regional and seasonal basis, and comparison among a control group. The result shows that the generation performance of hydrogen powered fuelcell is greatly affected by geographical change rather than seasonal effect. In addition, as the latitude of the hybrid systems location decrease, renewable power output and penetration ratio (%) increase under constant electrical load. Therefore, the hydrogen based hybrid system creates the stability of electricity generation, which best suits in the southern part of South Korea.

• Journal of the Korean Geotechnical Society
• /
• v.16 no.3
• /
• pp.119-129
• /
• 2000

국내에서 가장 많이 사용되는 현장조사방법인 표준관입시험의 결과로 얻어지는 N값에 대해 가장 큰 영향을 미치는 롯드 에너지 전단률(깽 Energy Ratio)을 지반조건이 상이한 3개 현장에서 항타분석기(Pile Driving Analyzer)를 이용하여 실측하였다. 에너지 전달률에 영향을 미치는 요인들 중엣 해머의 종류, 로프의 상태, 자아틀에 감은 횟수 등의 조건을 달리하여 롯드 에너지 전달률에 미치는 영향을 측정/분석하였다. 실험결과에 의하면 도넛해머, 안전해머, 개량형 도넛해머(Modified Automatic Donut Hammer)는 롯드에너지 전달률이 각각42%, 66%, 57% 정도로 측정되었으며 로프의 상태와 자아틀에 감은 횟수는 상대적으로 영향이 적은 것으로 측정되었다. 실험결과를 바탕으로 실측된 N값을 해머의 이론적 위치에너지의 60%에 해당하는 에너지가 롯드에 전달되었을 때의 N값(N60)으로 변환하기 위한 식을 제안하였다.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.519_520
• /
• 2009

신재생 에너지원을 포함한 대부분의 소용량 분산전원(DER : Distributed Energy Resource)은 22.9 KV 이하의 저압 배전계통에 분포하게 된다. 배전계통에 도입되는 분산전원(DER)에 의한 역조류 문제는 수용가 단의 전압상승 문제를 야기 시킬 뿐 아니라 보호계전 시스템의 전반적인 재검토를 필요로 한다. 출력 제어가 불가능한 분산전원(DER)의 도입량 증가에 따른 무효전력의 수급문제는 기존의 배전망 운영의 개념으로는 효율적인 제어가 어려우며, 유효전력의 급변에 의한 문제도 배전 지역별로 어느 정도 안정화 시킬 필요가 있다. 이를 위해서는 배전 계통운영에도 Energy Management System(D-EMS)의 도입이 필요할 것으로 사료된다. 본 논문은 D-EMS 도입 및 스마트그리드 체제로의 이행을 위한 통신네트워크의 아키텍처 수립을 위한 기능분석 결과이다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.133.2-133.2
• /
• 2011

2012년 RPS 제도가 시행되게 되면 발전설비용량 기준 500MW이상의 발전 사업자는 전체 전력생산량 중 일정 부분을 신재생에너지로 생산, 공급해야 한다. 최근 지경부에서 고시한 제5차 전력수급기본계획에서도 이러한 점을 반영하여 2024년까지 전체 발전량의 8.9%를 신재생에너지원으로 대체하겠다고 발표하였다. 신재생에너지 기술 수준, 시장여건 등을 고려하였을 때 앞으로 가장 크게 보급량(penetration)이 증가할 것으로 보이는 신재생에너지원은 태양광과 풍력인데 이 두 에너지원은 간헐성(intermittency)으로 인한 비급전성이라는 특징을 가지고 있어 향후 그 비중이 증가하면 전력계통의 안정성에 미치는 영향에 대해 고려해야할 것으로 보인다. 본 연구에서는 태양광과 풍력의 간헐성을 고려했을 때 추가적으로 발생하는 비용을 고려했을 경우 각 에너지원의 용량비용은 어떻게 되는지 알아보고자 한다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.4
• /
• pp.813-824
• /
• 1988

Use of a plasma arc as the source of energy for penetration welding of thin plates gives rise to a cylindrical hole surrounded by the molten metal. Material moves from the front to the rear of the hole by flowing around the hole as the workpiece is translated relatively to the arc. Based on the finite difference method, three different computer models have been proposed for the steady state, two dimensional heat and mass flow during the plasma arc welding. In the formulation energy equation was derived by the energy blance method through the cell control volume, and all the governing equations derived for the fixed coordinates was translated for the moving coordinate system. The driving force for fluid flow being considered was only electromagnetic force. The calculated and measured molten poon and HAZ width were compared and better agreement was obtained for the models considering the keyhole effect.

• Geomechanics and Engineering
• /
• v.15 no.3
• /
• pp.811-822
• /
• 2018

Chip size distribution can be used to evaluate the cutting efficiency and to characterize the cutting behavior of rock during cutting and fragmentation process. In this study, a series of linear cutting tests was performed to investigate the effect of cutting conditions (specifically cut spacing and penetration depth) on the production and size distribution of rock chips. Linyi sandstone from China was used in the linear cutting tests. After each run of linear cutting machine test, the rock chips were collected and their size distribution was analyzed using a sieving test and image processing. Image processing can rapidly and cost-effectively provide useful information of size distribution. Rosin-Rammer distribution pamameters, the coarseness index and the coefficients of uniformity and curvature were determined by image processing for different cutting conditions. The size of the rock chips was greatest at the optimum cut spacing, and the size distribution parameters were highly correlated with cutter forces and specific energy.

• Journal of Welding and Joining
• /
• v.21 no.6
• /
• pp.33-39
• /
• 2003

Wavelet transform analysis results show a spectrum energy distribution of CWT along scale factors distinguish the partial, full and over penetration in a electron beam welding by analyzing the curve of spectrum energy at small scale, middle and large scale range, respectively. Two types of signals collected by Ion collector and x-ray sensors and analyzed. The acquired signals from sensors are very complicated since these signals are very closely related the dynamics of keyhole which interact the very high density energy with materials during welding. The results show the wavelet transform is more effective to diagnosis than Fourier Transform, further for the general welding defects which are not a periodic based, but a transient, non-stationary and time-varying phenomena.

• Journal of Ocean Engineering and Technology
• /
• v.19 no.6 s.67
• /
• pp.1-7
• /
• 2005

This paper deals with the design and aerodynamic analysis of a special-type impulse turbine, with an end plate for wave energy conversion. Numerical analysis was performed using a CFD code, FLUENT. The main idea of the proposed end plate was to minimize the adverse effect of tip clearance of turbine blade, and was borrowed from ducted propeller, with so-called penetrating end plate for special purpose marine vehicles. Results show that efficiency increases up to $5\%$, depending on the flow coefficient; a higher flow coefficient yields increased efficiency. Decrease of input coefficient CAwith an end plate is the main reason for higher efficiency. Performance of end plate at various design parameters, as well as flow conditions, was investigated; the advantages and disadvantages of the presentimpulse turbine were also discussed.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.1151-1152
• /
• 2006

In this paper, we examined 10 domestic samples of three different model using thermal, humidity freeze, thermal-endurance and damp heat test under IEC61215 photovoltaic module environmental endurance test condition. Three was almost no changes on power generation. Insulation resistance capacity was much higher than judgement standard but, showed unstable results depending on environmental test items. On external appearance test, there were two models which showed bubble, humidity penetration, seal melted frame phenomenon. From this results, the degree of aging under the external environment is a main cause that shortens photovoltaic module life time. So it is considered that the efforts for finding optimum condition of manufacturing process should be needed.

• KEPCO Journal on Electric Power and Energy
• /
• v.6 no.3
• /
• pp.315-319
• /
• 2020

The modern transportation and mobility sector is expected to encounter high penetration of Electric Vehicles (EVs) because EVs contribute to reducing the harmful emissions from fossil fuel-powered vehicles. With the prospective growth of EVs, sufficient and convenient facilities for fast charging are crucial toward satisfying the EVs' quick charging demand during their trip. Therefore, the Fast Electric Vehicle Charging Stations (FECS) will be a similar role to gas stations. In this paper, we study a charging scheduling problem for the FECS with solar photovoltaic (PV) and an Energy Storage System (ESS). We formulate an optimization problem that minimizes the operational costs of FECS. There are two cost and one revenue terms that are buying cost from main grid power, ESS degradation cost, and revenue from the charging fee of the EVs. Simulation results show that the proposed scheduling algorithm reduces the daily operational cost by effectively using solar PV and ESS.