• Journal of Bio-Environment Control
• /
• v.3 no.2
• /
• pp.106-118
• /
• 1994

This study was conducted to analyze the effects of fluctuations in temperature, light intensity and soil temperature on the growth of red pepper seedlings in the nonheated plastic houses with various number of layers and in the open field. Relationship between the optimal environment and the growth of seedlings was discussed, and the maximum and minimum outdoor temperatures in Kwangju area from 1941 to 1985 were analyzed. The results obtained were as follows; 1. The minimum temperature in tunnel with quadruple coverings of P. E. film from December 20 to February 25 was decreased to 5$^{\circ}C$ mostly, where the exposure to chilling temperature could not be avoided during this period. The maximum temperature was increased to 33$^{\circ}C$ mostly and 42$^{\circ}C$ in peak, where some ventilation was needed. 2. The diurnal differences of inside temperature, increasing with number of layers, were 16 to 38$^{\circ}C$, while those of outside temperature were 5 to 1$0^{\circ}C$. 3. The cold injury in the quadruple coverings during winter occurred all the times below 12$^{\circ}C$ and as many as 200 times over 3$0^{\circ}C$, while effectiveness of thermal insulation in the multilayered nonheating plastic houses were clearly proved. 4. The inside light intensity was markedly reduced with the increment of layers and the minimum light intensity fallen down below the light compensation point for the growth of red pepper plants regardless of the number of layers. 5. Until 10 a. m., the temperature in the daytime during December 20 to mid - February showed below 10 to 12$^{\circ}C$ which was the limiting temperature for the growth of red pepper seedlings. After 4 p. m., the light intensity was sharply reduced despite of the air temperature kept over 12$^{\circ}C$. Therefore, limiting factors for the growth of red pepper seedlings were the temperature before 10 a. m. and the light intensity after 4 p. m. 6. The minimum soil temperature in quadruple coverings showed around 1$0^{\circ}C$ where the physiological damage for red pepper seedlings might be occurred. 7. The minimum outdoor temperatures from 1941 to 1985 was -19.4$^{\circ}C$, observed in the 5th January.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.18 no.4
• /
• pp.304-309
• /
• 2015

To evaluate the degree of contamination caused by oil spill accident in the sea, the in-situ sensors which are based on the scientific method are needed in the real site. The sensors which are based on the fluorescence detection theory can provide the useful data, such as the concentration of oil. However these kinds of sensors commonly are composed of the ultraviolet (UV) light source such as UV mercury lamp, the multiple excitation/emission filters and the optical sensor which is mainly photomultiplier tube (PMT) type. Therefore, the size of the total sensing platform is large not suitable to be handled in the oil spill field and also the total price of it is extremely expensive. To overcome these drawbacks, we designed the fluorimeter for the oil spill detection which has compact size and cost effectiveness. Before the detail design process, we conducted the experiments to measure the excitation and emission spectrum of oils using five different kinds of crude oils and three different kinds of processed oils. And the fluorescence spectrometer were used to analyze the excitation and emission spectrum of oil samples. We have compared the spectrum results and drawn the each common spectrum regions of excitation and emission. In the experiments, we can see that the average gap between maximum excitation and emission peak wavelengths is near 50 nm for the every case. In the experiment which were fixed by the excitation wavelength of 365 nm and 405 nm, we can find out that the intensity of emission was weaker than that of 280 nm and 325 nm. So, if the light sources having the wavelength of 365 nm or 405 nm are used in the design process of fluorimeter, the optical sensor needs to have the sensitivity which can cover the weak light intensity. Through the results which were derived by the experiment, we can define the important factors which can be useful to select the effective wavelengths of light source, photo detector and filters.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.32 no.1
• /
• pp.55-71
• /
• 1990

The purpose of this study is to find out the basic data for irrigation plans of red pepper and radish during the growing period, such as total amount of evapotranspiration, coefficent of evapotranspiration at each growth stage, the peak stage of evapotranspiration, the maximum ten day evapotranspiration , optimum irrigation point, total readily available moisture and intervals of irrigation date. The plots of experiment were arranged with split plot design which were composed of two factors, irrigation point for main plot and soil texture for split plot, and three levels ; irrigation point with pH1.7-2.0, pF2.1-2.4 and pF2.5-2.8, at soil texture of sandy soil, sandy loam and silty clay for both red pepper and radish, with two replications. The results obtained are summarized as follows. 1.1/10 exceedance probability values of maximum total pan evaporation during growing period for red peppr and radish were shown as 663.6 mm and 251.8 mm. respectively, and those of maximum ten day pan evaporation for red pepper and radish, 67.1 mm and 46.9 mm, respectively. 2.The time that annual maximum of ten day pan evaporation can he occurred, exists at any stage between the middle of May and the late of August for red pepper, and at any stage between the late of August and the late September for radish. 3.The magnitude of evapotranspiration and its coefficient for red pepper was occurred large in order of pF1.7-2.0 pF2.1-2.4 and pF2.5~2.8 in aspect of irrigation point and the difference in the magnitude of evapotranspiration and of its coefficient between levels of irrigation point was difficult to be found out due to the relative increase in water consumption resulted from large flourishing growth at the irrigation point in lower water content for radish. In aspect of soil texture they were appeared large in order of sandy loam, silty clay and sandy soil for both red pepper and radish. 4.The magnitude of leaf area index was shown large in order of pF2.1-2.4, pF2.5-2.8, and pFl.7-2.0, for red pepper and of pF2.5-2.8, pF2.1-2.4, pFl.7-2.0 for radish in aspect of irrigation point, and large in order of sandy loam, silty clay, sandy soil for both red pepper and radish in aspect of soil texture 5.1/10 exceedance probability value of evapotranspiration and its coefficient during the growing period for red pepper were shown as 683.5 mm and 1.03, respectively, while those of radish, 250.3 mm and 0, 99. respectively. 6.The time that the maximum evapotranspiration of red pepper can be occurred is in the middle of August around the date of ninetieth to hundredth after transplanting, and the time for radish is presumed to be in the late of September, around the date of thirtieth to fourtieth after sowing. At that time, 1/10 exceedance probability value of ten day evapotranspiration and its coefficient for red pepper is assumed to be 81.8 mm and 1.22, respectively, while those of radish, 49, 7 mm and 1, 06, respectively. 7.Optimum irrigation point for red pepper on the basis of the yield of raw matter is assumed to be pFl.7-2.0 for sandy soil, pF2.5-2.8 for sandy loam, and pF2.1-2.4 for silty clay. while that for radish is appeared to be pF2.5-2.8 in any soil texture used. 8.The soil moisture extraction patterns of red pepper and radish have shown that maximum extraction rates exist at 7 cm deep layer at the beginning stage of growth in any soil texture and that extraction rates of 21 cm to 35 cm deep layer are increased as getting closer to the late stage of growth. And especially the extraction rates have shown tendency to be greatest at 21cm deep layer from the most flourishing stage of growth for red pepper and at the last stage of growth for radish. 9.The total readily available moisture on the basic of the optimum irrigation point become 3.77-8.66 mm for sandy soil, 28.39-34.67 mm for sandy loam and 18.40-25.70 mm for silty clay for red pepper of each soil texture used but that of radish that has shown the optimum irrigation point of pF2.5-2.8 in any soil texture used. 12.49-15.27 mm for sandy soil, 23.03-28.13 mm for sandy loam, and 22.56~27.57 mm for silty clay. 10.On the basis of each optimum irrigation point. the intervals of irrigation date at the growth stage of maximum consumptive use of red pepper become l.4 days for sandy soil, 3.8 days for sandy loam and 2.6 days for silty clay, while those of radish, about 7.2 days.

• Clinical and Experimental Reproductive Medicine
• /
• v.27 no.2
• /
• pp.117-131
• /
• 2000

Objectives: To develop a new immunohistochemical marker system for supplementation of the Noyes histological classification of the endometrium in women of child bearing age with regular menstrual cycles, and to employ this system to evaluate pathologic factors involved in endometriosis, and thus to ascertain if it is useful in diagnosis. Materials and Methods: Endometrial biopsies were sampled from the posterior fundus of 41 (24 proliferative phases, 17 secretory phases) women with regular menstrual cycles (28-32 days), and each sample was immunohistochemically stained according to Noyes et al (1975) for determination of expression for estrogen receptor (ER), progesterone receptor (PR), integrin ${\alpha}_1$, ${\alpha}_4$, ${\beta}_3$, COX-1 and COX-2. Then, the PR, integrin ${\beta}_3$ and COX-2 which were clearly expressed in the luteal phase was with endometrial samples were obtained from 20 cases of normal patients (group 1) and 25 cases with endometriosis (group 2) after confirming the day of ovulation by sex steroid level measurements 7-8 days after ovulation Results: In the regular menstruation group the expression of ER showed a tendency to be increased in the proliferative phase and decreased in the secretory phase, and was the highest in the proliferative phase. However, PR in the stromal cells showed no change in the entire menstrual cycle while in the epithelial cells, PR reached a peak in the late proliferative phase and was almost absent in the secretory phase. Integrin (${\alpha}_1$, ${\alpha}_4$, and ${\beta}_3$ expression in the epithelial cells was absent in the proliferative phase but ${\alpha}_1$ was strongly expressed starting from the early secretory phase into the entire secretory phase. ${\alpha}_4$ was expressed strongly in the early and mid secretory phases and disappeared in the late proliferative phase, while ${\beta}_3$ appeared after the mid secretory phase and continued to be expressed until the late secretory phase. Expression in the stromal cells was weak overall and did not show any cyclic pattern. COX-1 expression was shown as a cyclic pattern in the stromal and epithelial cells and was particularly strongly expressed in the mid secretory phase of epithelial cells, and in the mid secretory and menstruation phase of stromal cells. In the endometrial epithelial cells there was strong expression during the entire cycle with stronger expression in the secretory phase compared to the prolferative phase. COX-2 was clearly expressed in the late proliferative, early and mid secretory phases in the stromal cells. No expression was observed in the proliferative phase of the epithelial cells, but which began to appear in the early secretory phase reaching a significant pattern from the mid secretory phase onwards. There was almost no expression in the stromal cells. In the cases with endometriosis showing normal endometrial maturation according to the Noyes classification, PR expression was increased while Integrin-${\beta}_3$의 expression was significantly decreased compared to the normal group. Also, COX-2 expression was slightly decreased in the stromal cells of patients with endometriosis while it was significantly increased in the stromal cells. Conclusion: Immunohistochemical markers can supplement the original Noyes classification of histological endometrial dating and therefore ascertain existing pathologic conditions. Particularly for patients with endometriosis with normally mature endometrial cells, changes in COX-2 and integrin expression patterns may assist in elucidating pathophysiologic mechanisms and therefore aid in the diagnosis of abnormal implantation conditions, and consequently determine a treatment modality.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.5
• /
• pp.133-137
• /
• 2017

The purpose of this study was to validate for GATE (Geant4 Application for Tomographic Emission) simulation by comparing the results of GATE simulation and experiment in real SPECT system. Futhermore, we want to prove that it is possible that the quantitative research of gamma camera/SPECT imaging for therapeutic radio isotope by using GATE simulation. In this study, the SPECT system on simulation referred to the parameters of Stream-R Forte version 1.2 (Philips Medical System, Best and Heerlen, Netherlands). To understand the I-131 image of gamma camera/SPECT system, we acquired the energy spectrum and measured the full width at half maximum (FWHM) which comes from line spread function (LSF) with and without scatter material in real SPECT system. And to compare with experiment, we also measured the FWHM and acquired the energy spectrum without scatter material in GATE simulation. As a result, without scatter material, the energy peak was almost same location, which are located nearby 364 keV, and other spectrum factors are same tendency in both cases. The FWHM was increased by increasing the distance of source to detector, and the error rate was approximately 3.8%. When we used the line source with scatter material, energy spectrum also indicated similar tendency in both cases. As you confirmed earlier, GATE simulation included real instrument and radioisotope characters for therapeutic radioisotope. Therefore this result that it was possible that various quantitative study for therapeutic radioisotope imaging in gamma camera/SPECT using GATE simulation.

• Korean Journal of Ecology and Environment
• /
• v.33 no.4 s.92
• /
• pp.374-379
• /
• 2000

To elucidate the degradation mechanisms of organic materials in Lake Paldang, oxygen consuming rates in the water column, high molecular weight (HMW) organic materials and aggregates were analyzed. Also the chlorophyll a concentrations and environmental factors were measured three times in 1999. The concentrations of chlorophyll a ranged $5.5{\sim}14.2\;mg/m^3$ with the highest peak of $57.7\;mg/m^3$ at the surface water in April. Chlorophyll a concentration of aggregates retrieved from traps in 5 m and 20 m depths in May were 2779.5, $9044.8\;mg/m^3$, respectively. Those vlaues were more than 6 times higher compared with other months, and more than 49 times higher than water column chlorophyll a. Oxygen consuming rates of water column were in the narrow range of $0.4{\sim}0.5\;mg\;O_2\;l^{-1}\;day^{-1}$. HMW organic materials were using only small amount of oxygen, $0.01{\sim}0.04\;mg\;O_2\;l^{-1}\;day^{-1}$. The aggregates retrieved from 5 m depth by sediment trap consumed the oxygen in the range of $0.48{\sim}0.69\;mg\;O_2\;l^{-1}\;day^{-1}$, while aggregates collected from 20 m depth, 0.88 to $1.04\;mg\;O_2\;l^{-1}\;day^{-1}$. With these results, the HMW appeared not to be degraded in the water column, instead they seemed to be concentrated and affected the sediment oxygen demand.

• Pediatric Infection and Vaccine
• /
• v.21 no.2
• /
• pp.129-138
• /
• 2014

Purpose: Streptococcus pyogenes is an important cause of invasive diseases in children. We aimed to describe the clinical characteristics of invasive infections due to S. pyogenes in children in Korea. Methods: A retrospective study of children under 18 years of age with invasive infections due to S. pyogenes at Seoul National University Children's Hospital between March 1992 and December 2012, and Seoul National University Bundang Hospital between March 2003 and December 2012 was conducted. Demographic factors, clinical characteristics, laboratory findings, treatment, mortality and morbidity of all patients were reviewed. Results: A total of 30 among 36 cases identified as invasive disease due to S. pyogenes were available for review. There was a predominance for male subjects (male:female=2.75:1). The median age was 50 months (range 12 days to 15 years) and 53.3% were under 5 years of age. Skin and soft tissue infections (9/30, 30.0%), bacteremia without identified focus (4/30, 13.3%) and bone and joint infections (6/30, 20.0%) were the most frequent clinical presentations. Streptococcal toxic shock syndrome (3/30, 10.0%) pulmonary, abdomen and central nervous system infections (2/30, 6.7%) were also seen. There was a peak in number of patients in year 2012 (9/30, 30.0%). There were no cases of mortality. Erythromycin and clindamycin resistance rates were low by 3.8% and 7.5%, respectively. Conclusion: We studied the clinical presentations of invasive infections due to S. pyogenes during the past 20 years in Korean children. The findings of this study help us understand the characteristics of the disease, enhancing early recognition and prompting adequate antibiotic therapy which is important in reducing morbidity and mortality.

• The Journal of Korean Academy of Prosthodontics
• /
• v.45 no.1
• /
• pp.85-97
• /
• 2007

Statement of problem: Recently, anodic oxidation of cp-titanium is a popular method for treatment of titanium implant surfaces. It is a relatively easy process, and the thickness, structure, composition, and the microstructure of the oxide layer can be variably modified. Moreover the biological properties of the oxide layer can be controlled. Purpose: In this study, the roughness, microstructure, crystal structure of the variously treated groups (current, voltage, frequency, electrolyte, thermal treatment) were evaluated. And the specimens were soaked in simulated body fluid (SBF) to evaluate the effects of the surface characteristics and the oxide layers on the bioactivity of the specimens which were directly related to bone formation and integration. Materials and methods: Surface treatments consisted of either anodization or anodization followed thermal treatment. Specimens were divided into seven groups, depending on their anodizing treatment conditions: constant current mode (350V for group 2), constant voltage mode (155V for group 3), 60 Hz pulse series (230V for group 4, 300V for group 5), and 1000 Hz pulse series (400V for group 6, 460V for group 7). Non-treated native surfaces were used as controls (group 1). In addition, for the purpose of evaluating the effects of thermal treatment, each group was heat treated by elevating the temperature by $5^{\circ}C$ per minute until $600^{\circ}C$ for 1 hour, and then bench cured. Using scanning electron microscope (SEM), porous oxide layers were observed on treated surfaces. The crystal structures and phases of titania were identified by thin-film x-ray diffractmeter (TF-XRD). Atomic force microscope (AFM) was used for roughness measurement (Sa, Sq). To evaluate bioactivity of modified titanium surfaces, each group was soaked in SBF for 168 hours (1 week), and then changed surface characteristics were analyzed by SEM and TF-XRD. Results: On basis of our findings, we concluded the following results. 1. Most groups showed morphologically porous structures. Except group 2, all groups showed fine to coarse convex structures, and the groups with superior quantity of oxide products showed superior morphology. 2. As a result of combined anodization and thermal treatment, there were no effects on composition of crystalline structure. But, heat treatment influenced the quantity of formation of the oxide products (rutile / anatase). 3. Roughness decreased in the order of groups 7,5,2,3,6,4,1 and there was statistical difference between group 7 and the others (p<0.05), but group 7 did not show any bioactivity within a week. 4. In groups that implanted ions (Ca/P) on the oxide layer through current and voltage control, showed superior morphology, and oxide products, but did not express any bioactivity within a week. 5. In group 3, the oxide layer was uniformly organized with rutile, with almost no titanium peak. And there were abnormally more [101] orientations of rutile crystalline structure, and bonelike apatite formation could be seen around these crystalline structures. Conclusion: As a result of control of various factors in anodization (current, voltage, frequency, electrolytes, thermal treatment), the surface morphology, micro-porosity, the 2nd phase formation, crystalline structure, thickness of the oxide layer could be modified. And even more, the bioactivity of the specimens in vitro could be induced. Thus anodic oxidation can be considered as an excellent surface treatment method that will able to not only control the physical properties but enhance the biological characteristics of the oxide layer. Furthermore, it is recommended in near future animal research to prove these results.

• Journal of Korean Society of Forest Science
• /
• v.104 no.3
• /
• pp.421-426
• /
• 2015

The objective of this paper is to look into the growth of Cryptomeria japonica stand in South Korea along with the evaluation on their yields, followed by their carbon stocks and removals. A total of 106 sample plots were selected from Jeonnam, Gyeongnam, and Jeju, where the groups of standard are grown. We only used 92 plots data except outlier. As part of the analysis, the Weibull diameter distribution was applied. In order to estimate the diameter distribution, the growth estimation equation for each of the growth factors including the height, the diameter at breast height, and the basal area was drafted out and the verification for each equation was examined. The site index for figuring out the forest productivity of Cryptomeria japonica stand for each district was also developed as a Schumacher model and 30yr was used as a reference age for the estimation of the site index. It was found that the site index for Cryptomeria japonica stand in South Korea ranges from 10 to 16 and this result was used as a standard for developing the stand yield table. According to the site 14 in the stand yield table, the mean annual increment (MAI) of the Cryptomeria japonica reaches $7.6m^3/ha$ on its 25yr and its growing stock is estimated to be at $190.1m^3/ha$. This volume is about $20m^3$ as high as that of the Chamaesyparis obtusa. Furthermore, the annual carbon absorptions for a Cryptomeria japonica stand reached the peak at 25yr, which is 2.14 tC/ha/yr, $7.83tCO_2/ha/yr$. When compared to the other conifers, this rate is slightly higher than that of a Chamaecyparis obtusa ($7.5tCO_2/ha/yr$) but lower than that of the Pinus koraiensis ($10.4tCO_2/ha/yr$) and Larix kaempferi ($11.2tCO_2/ha/yr$). With such research result as a base, it is necessary to come up with the ways to enhance the utilization of Cryptomeria japonica as timbers, besides making use of their growth data.

• The Korean Journal of Food And Nutrition
• /
• v.29 no.5
• /
• pp.618-627
• /
• 2016

This study evaluated the hydration, gelatinization, and saccharification properties of rice processing for beverage development. The properties of rice were studied on 10 rice cultivars (Samkwang, Ilpum, Seolgaeng, Anda, Dasan-1, Goami-4, Danmi, American rice, Chinese rice, and Thai rice) and employing four kinds of pre-treatment methods (dry grain, wet grain, dry flour, and wet flour). The results showed that moisture content of rice was between 11.88~15.26%. Increase in soaking time along with highest water absorption was noted in American rice cultivar (46.81%). The water binding capacity of Thai rice was higher when compared to that of other rice flours. In addition, solubility and swelling power of rice were 4.52~26.65% and 0.19~2.05%, respectively. The amylose content of Goami-4 was higher in rice processing. Using a rapid visco analyzer (RVA), the initial pasting temperature of Danmi cultivar was found to be the highest; the peak viscosities of Anda cultivar and Dasan-1 cultivar, and Chinese rice were higher than of those of other rice flours. After saccharification, the pH, soluble solids content, and reducing sugar content of rice processed through different pre-treatment methods were in the range of 6.22~7.08, $4.67{\sim}16.07^{\circ}Brix$, and 0.35~11.67% (w/w), respectively. In terms of color values, the L-value of dry grain, a-value of wet (grain, flour), and b-value of dry sample (grain, flour) were found to be the highest. Assessment of various factors and cultivars characteristics of the raw grains are of importance in the development of rice beverage.